I need directions on where the camshaft sensor is located

Top part says you want Camshaft Sensor, but the bottom says you want Crankshaft Sensor??

Camshaft
https://www.google.com/search?q=2012+dodge+caliber+3.0+camshaft+sensor+location

Crankshaft
https://www.google.com/search?q=2012+dodge+caliber+3.0+crankshaft+sensor+location

..

There is two sensor one one each head here is a guide to help walk you through the replacement and the location of the sensors in the diagrams below.

https://www.2carpros.com/articles/camshaft-angle-sensor-replacement

https://www.youtube.com/watch?v=dp0haTIErvU this video will point you in the right direction here is a link to a picture https://www.2carpros.com/images/external/79028252.gif

The camshaft position sensor is located on top of the engine near the ignition coils.
The camshaft position sensor is located on top of the engine near the ignition coils.
The camshaft position sensor is located on the engine near the timing belt cover and under the upper radiator hose.
The camshaft position sensor is either located near the top of the engine, passenger-s side, or on the right side of the engine near the ignition coils.
The camshaft position sensor is located on the engine near the camshaft pulley.
This sensor is located at the front of the engine near the camshaft gear this is what I got 6 different locations manual covers 99-05

Open the hood for access to the engine compartment. Locate the front of the engine facing toward the passenger side of the Olds 88. Locate the pulleys along the front of the engine. Look for the camshaft pulley, which is the main pulley and is also the largest pulley of all the pulleys in the engine.3 Find the water pump pulley directly above the camshaft. The camshaft sensor is located between the two pulleys. The sensor is round with a wiring harness sticking out of the end.

The camshaft sensor is located in the distributor. The sensor functions as an ignition device in the Enhanced Distributor Ignition system. In the event of failure or damage, the sensor is not directly involved with driveability.

well I dont know that car, but if you know where the camshaft is (middle of the engine) look where the front cam gear is. Its got to pick up a signal from the gear/magnet.

The crank sensor is on the lower rear side of the block.

the camshaft sensor is mounted on the camshaft housing located on the end of the cylinder head.

2.0L 2.4L Removal The camshaft position sensor is mounted to the rear of the cylinder head.

Remove the negative battery cable. Disconnect the PCV hose and reposition Disconnect electrical connectors from the camshaft position sensor. Remove camshaft position sensor mounting screws. Remove sensor.Loosen screw attaching target magnet to rear of camshaft and remove magnet.
Instalation The target magnet has locating dowels that fit into machined locating holes in the end of the camshaft.
- Install target magnet in end of camshaft. Tighten mounting screw to 3 Nm (30 in. lbs.) torque. Over torqueing could cause cracks in magnet. If magnet cracks replace it.
- Install camshaft position sensor. Tighten sensor mounting screws to 12.9 Nm (115 in. lbs.) torque.
- Carefully attach electrical connector to camshaft position sensor. Installation at an angle may damage the sensor pins. - Connect the PCV Valve hose. - Connect the negative battery cable.
2.7L V6 Removal
The camshaft position sensor is mounted in the front of the head.

Disconnect electrical connector from sensor. Remove camshaft position sensor screw.
CAM Sensor Location 2.7L
Without pulling on the connector, pull the sensor out of the chain case cover.

Installation - Install sensor in the chain case cover and push sensor in until contact is made with the boss on the head. While holding the sensor in this position,install and tighten the retaining bolt to 12 Nm (105 in. lbs.) torque.
- Attach electrical connector to sensor.

Good luck and hope this helps