I have a 95 dodge intrepid with a 3.3 V6 and i need to know if i need to jack the aar up and remove the starter from beneath the car or can I take it out while its still on the ground?? need help ASAP

well it is easy to get to for it is up top,and not at the bottom of the car. you will need to jack it up and remove both front tire,so you can remove both outer tie rod ends from the spindle. then there is a plate that locks the 2 bigs bolts in place .remove the bolts and slid it out the side. make sure you put the plate back in place after

YOU NEED BASIC TOOL SET WITH METRIC AND STANDARD SOCKETS.YOU NEED FLOOR JACK AND JACK STANDS. IF YOU HAVE THE 2.7L ENGINE YOU HAVE TO USE A FLOOR JACK WITH A PIECE OF WOOD IN JACK LIFT SADDLE.PLACE JACK UNDER THE ENGINE OIL PAN SLIGHTLY RAISE ENGINETO TAKE WEIGHT OFF THE FRONT ENGINE MOUNT SINCE YOU HAVE TO REMOVE THE FRONT ENGINE MOUNT BOLTS AND MOUNT BRACKET.OUT OF THE WAY TO REPLACE STARTER ONLY DO THIS PROCEDURE IF YOU HAVE THE 2.7L ENGINE.BE SURE TO TURN OFF RADIO FIRST BEFORE REMOVING NEGATIVE BATTERY TO KEEP FROM LOCKING OUT RADIO.

Remove both drive axles first. Remove started.. remove transmission blots and torque convertor bolts. remove engine mounts. Support the engine with another jack to keep it level. 2 or 3 hours to do by yourselt...Good Luck!!!

nonsense--should be easy according to autozone.com:

3.3L Engine

See Figures 9, 10 and 11

1. Disconnect the negative - battery cable. Raise and safely support the front of the vehicle on jackstands.

Fig. Fig. 9: Disconnect the negative battery cable

1. Remove the three bolts attaching the starter to the engine/transaxle.

Fig. Fig. 10: Remove the three starter mounting bolts

1. Remove the starter from the the transmission housing. Position the starter to gain access to the wiring connectors.
2. Remove the battery positive cable nut from the starter and remove the cable.

Fig. Fig. 11: Remove the battery positive cable nut from the starter and remove the cable

1. Disconnect the push on solenoid connector.
2. Remove the starter from the vehicle.

To install:

1. Clean all wire terminals of dirt, grease or corrosion.
2. Attach the electrical wire connectors and secure with the mounting nuts. Tighten the starter solenoid B+ nut to 90 inch lbs. (10 Nm) and the solenoid wire-to-starter nut to 55 inch lbs. (6 Nm).
3. Hold the starter motor in place, then secure in place with the 3 attaching bolts. Tighten the bolts to 40 ft. lbs. (54 Nm).
4. Lower the vehicle.
5. Connect the negative - battery cable.

3.5L Engine
See Figures 9 and 12

1. Disconnect the negative battery cable.
2. Raise and support the vehicle.
3. For easier servicing, do not remove the wiring from the starter motor at this time.
4. Remove the three bolts attaching the starter to the engine.

Fig. Fig. 12: Remove the three bolts attaching the starter to the engine

1. Remove the starter solenoid assembly from the transfer housing. Position the starter to gain access to the wiring connectors.
2. Remove the battery positive cable nut from starter and remove the cable.
3. Disconnect the push on solenoid connector.
4. Remove the starter from the vehicle.

To install:

1. Clean all wire terminals of dirt, grease or corrosion.
2. Attach the electrical wire connectors and secure with the mounting nuts. Tighten the starter solenoid B+ nut to 90 inch lbs. (10 Nm) and the solenoid wire-to-starter nut to 55 inch lbs. (6 Nm).
3. Hold the starter motor in place, then secure in place with the 3 attaching bolts. Tighten the bolts to 40 ft. lbs. (54 Nm).
4. Lower the vehicle.
5. Connect the negative battery cable.

have you tried to activate the starter relay? check the nuetral safety switch?

For the 1996 Dodge Intrepid 3.5L SOHC V6

Firing Order:
1-2-3-4-5-6

Cylinders:
......(back)
1........3........5
2........4........6
.....(front)

Ignition Coil Connections:
(back)
6....3
4....1
2....5
(front)

Let me know if this helped, or if you have additional informtion or questions. Feel Free to contact me at FixYa.com!

to get to the battery you neeed to removed the passanger side tire nad the is a plastic shiel you need to removed to get to the batery,
the starter is located on the driver side of the engine and you can see ie fron under the car, there are 3 bolts

make sure you have spark, sometimes if you start bypassing stuff the ignition works only on a resistor to much electricity and it won't work, not enough and it won't work.

under the car by the battery. to replace-remove wheel well cover on front river tire

If I'm correct, I'm not sure, it's easier to jack up driver's side of car and have the wheels turned to the right. There are splash sheilds that you'ld have to remove. From there you can get your arm in to work with the starter. It's a tight fit though but doable. When you remove the starter the flywheel cover will come with. Make sure you put it back on exactly. So pay attention. I found out the hard way. Like I said I'm not sure. I worked on a dodge intrepid or concord around the same year. Since I'm a GM man, I don't remember it's a completly different setup or not.