Have a 92 SVX. The tilt steering wheel will only lock in the low down position, otherwise it just floats! Any ideas?

Steering Wheel Adjustment .The lever is located under the steering column, slightly to the left. To adjust the steering wheel: 1. Pull the lever down. 2. Move the steering wheel up or down into a comfortable position. 3. Pull the lever up to lock the wheel in place. Do not adjust the tilt lever while driving.

Just the key or the whole lock cylinder with key ?

Removal Procedure
Caution: Unless directed otherwise, the ignition and start switch must be in the OFF or LOCK position, and all electrical loads must be OFF before servicing any electrical component. Disconnect the negative battery cable to prevent an electrical spark should a tool or equipment come in contact with an exposed electrical terminal. Failure to follow these precautions may result in personal injury and/or damage to the vehicle or its components.
Disconnect the battery negative cable.
Disable the SIR system. Refer to Disabling the SIR System
Position the steering wheel half way between the upper and lower tilt stops (if necessary).
Remove the steering wheel. Refer to Steering Wheel Replacement .
Roll back the shift lever seal from the upper and the lower shrouds.
Remove the tilt wheel lever (if necessary). Refer to Tilt Lever Replacement - On Vehicle .
Remove the 2 TORX® screws from the lower steering column shroud.
Remove the lower steering column shroud.
Remove the 2 TORX® screws from the upper steering column shroud.
Lift the upper steering column shroud to gain access to the lock cylinder access hole.
Using a bent tip awl, insert the tip into the ignition lock cylinder access hole.
Turn the ignition lock cylinder to the START position.
Using the bent tip awl, push down on the ignition lock cylinder retaining pin.
Release the ignition lock cylinder to the RUN position.

Remove the ignition lock cylinder from the lock module assembly by pulling the ignition lock cylinder away from the steering column.

There may be a video on youtube .

This happens with my ram. The tilt wheel locking pin is stuck. When this happens to me i have to wiggle my steering wheel up and down and pull on the tilt release lever at the same time until the locking pin slides out of it's locked position. I have found that if i do not lock the wheel in the max up or max down position i do not have this problem.

I had an SVX, and loved it! Had to replace the power steering pump too, but I found that until I did a really thorough flush that it still didn't work right. Jack the front wheels off the ground. Have a helper get in the car to start it and turn the wheel back and forth. Before starting it, disconnect the low-pressure return hose from the pump and put the end of it into a bucket. Be ready with a couple of quarts of ATF fluid (you don't need to use power steering fluid.) Start the car and pour fresh fluid into the pump while the steering wheel is being turned all of the way back and forth a couple of times. Don't let the fluid level get down to where it pumps any air! Shut it off just before you finish pouring in the second quart of ATF. Reconnect the low pressure hose, run it again and adjust the fluid level. This worked for me - the steering operated like new. Good luck.

Hi,

Usually, vehicles with tilt adjust steering, have a small lever just under the steering wheel column. Pulling this lever out, unlocks the wheel. Pushing lever back in, locks the wheel.

Have a look for a lever of this type and once you find it, have your Dad hold the steering wheel at his preferred position, then push the locking lever back up, to lock the wheel in place.

Let me know if you resolve this.....


Cheers,

your steering wheel adjuster is blocked or stuck up thats why it doesnt freely move to the max. take off cover/ check condition and or lubricate it.

Yes it would be perfectly ok to disegauge the auto switch to keep it from moving again. It needs a tilt motor replaced . not a easy job.

When they did the alignment it's possible that they used a tool that locks the steering wheel straight while it's on the alignment rack.If they put too much pressure on the wheel when they used the steering wheel seat lock tool it may have stressed you tilt lock mech causing it not to lock where you want it.Hope this helps

You have a tilt steering wheel! This is a problem with most GM tilt wheels. There is 3 or 4 screws you need to have tightened up; which requires tearing down the steering to get to them and put lock tight on them and tighten them back up, so they will not happen again for a long time.