94 nissan power windows not working

There is no separate fuse for power windows:
https://www.2carpros.com/questions/nissan-altima-2006-nissan-altima-windows-and-locks

https://oards.com/causes-of-power-windows-not-working/

How to fix the Chev power window door lock switch - YouTube

? 5:04
https://www.youtube.com/watch?v=XDKaDURD8Sc
Jul 13, 2013 - Uploaded by spelunkerd
How to fix the Chev power window door lock switch ..... Some time later my drivers side window stopped working in the down position. ... These intermittent electrical problems are frustrating,aren't they? .... How To Install Replace Door Locks Chevy GMC Truck Silverado Sierra Yukon Tahoe Suburban ...

Diagnose Power Door Locks Dont Work Properly - Auto ...

www.auto-repair-help.com/.../diagnose_power_door_locks_dont_work_...

An inoperative power door lock can be caused by the switch, solenoid, wiring problem or ... Hi, I have a 2005 Nissan Sentra and the power locks aren't working. .... Hi, mypassenger door locks/unlocks both doors but my driver side door works independently and .... I have a 1986 Chevy Silverado K10 with auto door locks.

SilveradoSierra.com • 2003 silverado no power in right door ...

www.silveradosierra.com/.../2003-silverado-no-power-in-right-door-t30...

check your interior door light switches are working, these control your alarm and door locks.

Very easy to do...I have a 1990 and they are interchangeable....88-94: Door Panel

1. Fully lower the door glass.
   
2. Remove the arm rest, door lock knob and inside door handle escutcheon.
   
3. For vehicles with manual windows, remove the regulator handle which is retained by a spring clip.
   
4. Gently pry the door panel away from the door.
   

Interior side and floor trim removal procedures-Pathfinder


Remove the lock button first before removing the door panel


Remove the plug to gain access to door panel retaining screws


Remove the trim cover


Remove the door handle trim


Remove the power window switch trim panel


After loosening the power window switch trim panel, disengage the electrical connection


Remove all the necessary trim panels before removing the door panel clips


View of the door panel retaining clip-clip must be installed in the hole straight


Make sure the watershield plastic is in place before installing the door panel

Installation is the reverse of removal.

try checking your relays

Well, it sounds like the window motor is drawing too much current. The window motor may not be any good. But before condeming motor, grease the window channels with a silicone base spray and make sure window moves up and down easy without much resistanse. If thats ok, then replace the window motor/regulator assembly.

You need a body control computer, which controls the windows, door locks and other items. The new computer will have to be programed by a good imports shop or Nissan dealer.

about the only advice i can give is that i did the same thing with a 94 probe base and a 94 gt. i had to take the whole wiring harness out of the gt and put it in the base. It starts from the inside fuse block, goes to both doors, under the front seats, all the way to the fuel pump, abs, tail lights, and pretty much everything from the dash to the rear of the car. If you can get a whole harness, it should work.

Try Prying Them Up If Ones Disconnected On Some Cars All The Buttons On Any Other Door Will Not Operate. You Also May Want To Check The Fuses.+

On my girlfriend's Civic, the same problem cropped up and it was the driver's door switch assembly. The power for all the windows is routed to the driver's door switches, and from there, out to the other doors (that's how the window lock on the driver's door is able to shut off the window power in the back doors). If your driver's door switch assembly has failed, you'd have no power to the windows, regardless of which switches you're trying to use. I'd suggest going to a salvage yard and finding a new driver's door switch assembly and swapping it into your car and see if that fixes it. It shouldn't run you more than $15 or so, and they're generally pretty easy to swap out - figure a few basic tools and maybe a half hour or 45 minutes of your time.