Question about 1995 Ford Aspire

Open Question

Repair front wheel bearing on a 1995 ford aspire straight shift

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 321 Answers

SOURCE: front wheel bearing 2004 escape 4x4

It's nearly impossible unless you have a good air compressor and a powerful 1/2" or larger drive impact gun.The reason is you have to remove the cv axle nut and axle out of the way before removing the bearing and hub.The axle nut requires a couple hundred foot pounds to remove.The procedure is:Jack vehicle safely off the ground,remove wheel and tire.Remove axle retaining nut.Remove balljoint nut and bolt,pry down on lower control arm,and disengage balljoint and lower arm from spindle.Now the axle can be released from the hub,but leave the other end of the axle in the trans,just set off to the side out of the way.At this point,there are two ways to change the bearing.The wheel bearing is a double roller,cartridge type with the hub containg the wheel studs,pressed into the bearing.Remove the entire spindle assembly from the suspension strut,OR leave the spindle attached to the strut,and remove the bearing and hub from the spindle.Some guys swear by taking the spindle to a press,and pressing the bearing assembly out with a bottle jack.I just use a bushing driver set,and ball peen hammer,and remove the hub from the bearing...then remove the snap ring retaing the bearing in the spindle,then drive the bearing out of the spindle with the hammer and drivers.There you have it.Reverse procedure for reassembly

Posted on Jul 11, 2008

Ad
  • 337 Answers

SOURCE: 1995 ford contour / passengerside wheel bearing

http://www.autozone.com/shopping/repairGuide.htm?pageId=0900c152800a8e08

Posted on Dec 07, 2008

  • 142 Answers

SOURCE: Replacing front wheel bearings

It isn't a particularly hard job but there are a few techniques that you need to know.
I wouldn't recommend you do it yourself but I would recommend you do it under supervision of someone who knows their stuff.
Retensioning the bearings correctly is extremely important.

Posted on Jun 27, 2009

  • 23 Answers

SOURCE: replace front wheel bearings 99 ford explorer

not press fitted, standard tapered bearings, if 4X4 it is a little more involved, just dont misplace any of the smaller parts and you will be fine.

Posted on Aug 29, 2009

Testimonial: "thanks for the speedy reply and also for the right advice."

  • 141 Answers

SOURCE: fixing a 2003 ford focus front wheel bearings

remove the hub and spinle ,tie rod end ,axle nut.ball joint,and seperate from strut and then have new bearing pressed in...or rent a bearing press that works with an impact wrench,but they are a little hard to work with...good luck...lee

Posted on Sep 07, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I think the bearing went out


either your brakes are metal on metal or your wheel bearing is worn. if your brakes look to be good, put the tire on and grab top and bottom of tire pushing and pulling to feel for back and forth play, you would know right away if there was cheers

Mar 13, 2010 | 1995 Ford Aspire

1 Answer

How do I replace the front wheel bearing in a 1995 ford taurus?


first off, sell the car and by another one, ford taurus is a very dear car to fix, let alone the wheel bearing will cost more then 2 tanks of gas, otherwise it is not an easy home doing job, you need special circlip pliers, a hammer at least a 3 tonne hydraulic press and a good eye for line up, most mechanics will do this but it is a bit hard to remove the actual wheel bearing if you never have done one. remember if the wheel bearing is one millimeter off it will grind like hell.

Dec 04, 2009 | 1995 Ford Taurus

2 Answers

I got grinding it the front wheel bering,,but only the left


ok you have a bad right front wheel bearing by what you are describing

Sep 04, 2009 | 1997 Ford Aspire

7 Answers

93 Ford Festiva wheel bearing job - any surprises?


No, the front wheel bearings are relatively easy to replace on the Festiva. They just knock out and press back in. I recently replaced the front bearings and all (4) struts on mine and it went well.

Sep 04, 2009 | 1993 Ford Festiva

1 Answer

Cost to replace wheel bearings on 1997 ford aspire


advance auto parts total price for all bearing, front and rear and seals come to $70.00. labor should be about that much(plus cost of grease) good luck

Sep 04, 2009 | 1997 Ford Aspire

1 Answer

Strut tower and bearing plate


yes it could or strut or tower could be bent they shifted it to get it to align up

Oct 03, 2008 | 1999 Ford Escort

2 Answers

Front wheel bearings


THe tire size is very important.
Originally ford aspire had 155 70 r 13.
It is impossible to find the same size in USA.
If you put a bigger tire...then you brake the wheel bearing.
My 2 cents
Art

Jul 19, 2008 | 1997 Ford Aspire

Not finding what you are looking for?
1995 Ford Aspire Logo

Related Topics:

240 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

83096 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

gerry bissi

Level 3 Expert

4387 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...