Question about 2002 Chrysler Concorde

1 Answer

My 2002 chrysler concorde signal lights will not work. I replaced the flasher and the multi function switch but they still dont work

Posted by on

  • 3 more comments 
  • tonysallis Dec 13, 2009

    Yes i did check & replace fuse 9 marked turn signals. is there more that i dont know about.

  • tonysallis Dec 13, 2009

    Do you know where this fuse is located?

  • tonysallis Dec 14, 2009

    the power distribution centre is that the bank of fuses and relays under the hood?

  • tonysallis Dec 14, 2009

    It was under the hood. Fuse marked O, 20 amp for hazard lights, thanx for all your help.

  • tonysallis Dec 19, 2009

    Ok now ive got problems with my blower motor resistor. Is there any way to bypass it n run the fan motor direct on high or something. i have to wait until next week for the part.

×

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Governor:

    An expert whose answer got voted for 20 times.

  • Expert
  • 173 Answers

Hello...

I know it may sound simple, but did you check all the applicable fuses.

Good Luck

Posted on Dec 13, 2009

  • Thomas Johnson Dec 13, 2009

    Not sure if you have it, but there is a fuse O (letter) that is part of the circuit. If that does not apply, its time time to start checking grounds and connectors. Also, make sure there are no blow blinker bulbs.



    Good Luck

  • Thomas Johnson Dec 13, 2009

    Sorry, from my information I cannot tell where it is located. It just states that it is in the Power Dist. Center (PDC).



    Good Luck



×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

My turnsignals dont work on my 1987 honda accord flashers do work


flashers and turn signals have separate flasher and separate fuse.

Mar 14, 2016 | Honda Cars & Trucks

Tip

Indicater or flasher problem on jeep cherokee 2003


If your having problems with your indicater or flashers on your vehicle then their are a couple of things that would be causing you problems.Now if when you press left or right turn the light flashes fast when turning one way but not the other then this indicates you have a blown bulb on the side that is causing it to flash faster so you need to press it to that side and have a look at the front and back bulbs and change the one thats not working.

If on the other hand your flasher/indicater works sometimes and not others then this is usually down to the flasher relay located in fuse box (see pictures below)
To find out if it is the relay and not the flasher control that you press to turn the indicator lights on is to try using the hazard warning light button press this and if this works every time then the chances are its the control and not the relay (see pictures below) but if it sometimes works and sometimes dont or if it dont work at all then this points towards the relay so changing this should then solve your problem



FLASHER REMOVAL
  1. Disconnect and isolate the battery negative lead.
  2. Remove the steering column opening cover from the instrument panel.
  3. Remove the combination flasher from the junction block
    Combination Flasher
  4. spacer.gif90ba789c.gifspacer.gifspacer.gifView Full Imagespacer.gif 1 - COMBINATION FLASHER 2 - JUNCTION BLOCK

Ispacer.gif2009-03-25_033953_wj005003.thumb.gifspacer.gifspacer.gifView Full Imagespacer.gifNSTALLATION
  1. replace the flasher relay into the possition you took the old one out of in junction block.
  2. make sure you line this up correctly to prevent damage being done to the pins when inserting it into the holder
  3. make sure that the flasher relay is inserted correctly and far enough make sure its seated flush the same as the other relay units.
  4. now all you need to do is re-fit the cover to the steering column
  5. Reconnect the battery negative cable.
TURN SIGNAL AND HAZARD WARNING SWITCH
REMOVAL
  1. Disconnect and isolate the battery negative cable.
  2. Remove the screw that secures the lower tilting steering column shroud to the steering column multi-function switch mounting housing Steering Column Shrouds Remove/Install
  3. disconnect the two halves of the tilting steering column shroud from each other and remove both halves from the steering column.
  4. Disconnect the wiring harness from the turn signal switch and make sure you remember how it comes out of the fitting to ensure you fit it back correctly as it was.
  5. Remove the two screws that secure the left multi-function switch to the multi-function switch mounting housing Left Multi-Function Switch Remove/Install
  6. Remove the left multi-function switch from the multi-function switch mounting housing.
INSTALLATION
  1. Position the left multi-function switch onto the multi-function switch mounting housing.
  2. Install and tighten the two screws that secure the left multi-function switch to the multi-function switch mounting housing. Tighten the screws to2.5 N·m (22 in. lbs.)
  3. re-fit the wiring harness to the switch.
  4. Position the lower tilting steering column shroud to the underside of the steering column.
  5. Instal land tighten the screw that secures the lower tilting steering column shroud to the multi-function switch mounting housing. Tighten the screw to 1.9 N·m (17 in. lbs.)
  6. Position the upper tilting column shroud over the steering column with the hazard warning switch button inserted through the hole in the upper surface of the shroud. Align the upper tilting steering column shroud to the lower shroud and snap the two shroud halves together.
  7. Reconnect the battery negative cable.
spacer.gif2009-03-25_033747_90b04f0f.thumb.gifspacer.gifspacer.gifView Full Imagespacer.gif

on Mar 21, 2010 | Jeep Cherokee Cars & Trucks

1 Answer

Need to no were the fasher location is on a 99 ford concord


"Need to know where the flasher location is on a 99 Ford Contour"

It is located or plugged into the side of the multi-function switch. If you remove the plastic covers from the steering column you will be able to replace the flasher.

Sep 27, 2014 | Cars & Trucks

1 Answer

2001 PT Cruiser loss of turn signals and hazard lights after multi-function switch replacement. I replaced the multi-function switch after noticing the fogs lights staying on when not engaged. When the new...


Perhaps you need to start with fog light problem I am guessing we do not know for sure the switch was the cause, if you can remove them from the equation. When checking for shorts make sure you check light bulbs to,
Next, since the multi function switch was the next step in your problem solving, I suggest you remove the new switch check out all wires to the connector, be especially careful to make sure none of wires have pulled out or partially pulled out of the connector. Let me know when you finish this then we can move on to continuity testing.
My best guess is the connector as it is common to both your fog light and multi-function switch,
Above all don't let it get to you, these problems can be frustrating but they also can be interesting and fun especially with the right assistant

Aug 25, 2013 | 2001 Chrysler PT Cruiser

1 Answer

Turn signals and brake lights will not work


A mechanic would check for voltage at the multi-function switch in the column. Those three circuits go thru the turn signal switch.

Jul 13, 2012 | 2002 Buick Rendezvous

3 Answers

I have a 2004 Monte Carlo, my turn signals and flashers just stopped working, the fuse is good and all the bulbs are good. Does anyone have any other ideas as to what is causing this problem.


The turn signal switch assembly often causes this problem. If the hazard button is on your steering column it is part of the switch assembly and is called a multi-function switch . If it has a separate hazard button on the dash the can also cause the the same thing to happen. Try holding very slight pressure on the hazard button on the dash while the turn signal is on. If it starts working correctly replace only the the hazard switch. It is usually just snapped into the hole in the dash. If the hazard switch is on the column, than you should replace the multi-function switch. If it is equipped with an airbag, be sure the key is off while working on column. The multi-function switch should not require removal of the steering wheel on this car.

Jan 07, 2011 | 2004 Chevrolet Monte Carlo

2 Answers

No signal lights


there are two different relays for flasher and turn, I would check the turn signal relay, if seems good I would check the switch.

Nov 11, 2009 | 2002 Dodge Durango

Not finding what you are looking for?
2002 Chrysler Concorde Logo

Related Topics:

310 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...