Question about 2005 Mazda 3

1 Answer

Hello, I have a 2005 Mazda 3i sedan and need a

Hello, I have a 2005 Mazda 3i sedan and need a description or diagram to show me how to remove the metal wire clip that holds the low-beam headlights in its housing. thanks for your help.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,092 Answers

Squeas wire and bulb will come out.

Posted on Dec 12, 2009

  • makua
    makua May 27, 2014

    Hi,my opel corsa utility died while i was driving.I tried to check the relays and the fuses but cant find the problem.The timing belt its ok and the battery is charging correctly.What could be the problem?

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i wire up hid headlights on 2005 mazda 3


To wire up an HID kit on the low beams of your Mazda 3 2005, you will need 3-4 things:
1- HID kit (bulbs and ballasts)
2- HID relay (connects your hid kit to your battery)
3- 4700uF capacitor (solves DRL flickering issue)
4- H7 hid bulb adaptor (you can also use the rubber piece that holds the bulb wires as a spacer)


Wiring diagram:
http://www.carsets.co.uk/upload/temp/images/hid-light-installation-photo-display.jpg

Tips on How to wire up:
1. HID bulb's amp wires connects with the ballast's amp wires. (There's only one way to connect them.)
2. The positive and the negative spade connectors from the hid relay connect with your vehicle's low beam connector, closest to your battery: the driver side. The passenger side low beam connector is not used and should be insulated. You can use electric tape.)
3. Each ballast is connected to one of the relay's clip connector, and it's grounded on each side to your vehicle's body. (One connector for each ballast, one for each side. You can use the screw for the body as a ground.)
4. The red wire(with the inline fuse) in the relay connects to your battery's positive terminal.
5. The capacitor sits on the relay switch. (Google for how to wire the capacitor onto the hid relay switch.) dynoxg image
6. The halogen bulb sits on an adapter. You can safely remove them from each other, and use an H7 hid adapter instead.

For more help: Moonlight Driving

Nov 06, 2011 | Cars & Trucks

1 Answer

Have a Nissan pathfinder 2005... The high beams don't wonk. I changed the bulbs and they still don't function.. Any idea how to fix this problem?


Did you check the relays? or the High beam switch? Usually you can trace the wiring down from the switch to a harness at bottom of steering column use test light there too.Use a Test Light at the headlight connection make sure that you have power Low beam then test high beam. If you can't figure out use of Test light, it has a ground clip and a probe (Sharp end)Ground the clip on something metal (on car) use the probe to touch wire (one at a time) in the socket where the headlight connections. 1 wire is ground 1 is LOW beam and other is HIGH beam. may need a mechanic to check the switch. The light on the tester will light up IF you have 12 volts. NO LIGHT NO POWER!

Oct 30, 2011 | Cars & Trucks

1 Answer

Replacing low beam headlight for a Madza 6 2004


Easier than high-beams, need to find the black turn covers just on the inside of the fender, release metal clip holding bulb and unplug light, replace resecure and put plastic cover back on should be good to go

Sep 25, 2011 | 2004 Mazda 6

2 Answers

How do i get to my low beams on my chrysler 2005 sebring sedan i got to the high beams perfect but the low beams right next to it has a metal barrier surrounding it which makes it impossible


Unfortunately, the answer I have is not a happy one =(. My wife has a 2005. In order to replace the bulb you will have to pull the Crutons (plastic push pins) that hold the front bumber cover on, remove the Headlight housing & replace the bulb that way. Shame on Chrysler for making it so difficult, in my opinion. But I hope this helps you to change the bulb =)

Aug 26, 2011 | 2004 Chrysler Sebring

1 Answer

Need to change the left side low beam headlight.


It might be hard to get to like that. You will see a silver metal bar with a 90 degree angle at the top that goes straight down behing the headlight assembly, which you can pull up on. It holds the headlight in. Once you pull this up pust the headlight slightly sideways as there is a plug holding the headlight in at the back, then just pull forward to give youself space to work. Clip off the two clips and slide the back cover off then you can change the bulb out.

Jul 09, 2010 | 2005 Volvo S40

1 Answer

Need to change low beam light on 2005 scion tc tried to remove headlight but it would not come out is there a hidden screw somewhere how do i remove the bulb from it's housing


Don't remove headlight. Look at the back of the headlight. and try to see a clip which will be holding the lampholder which holds the bulb. When you find this it will become possible but needing dexterity

Mar 27, 2010 | 2005 Scion tC

1 Answer

How do i change a headlight in a 07 Jetta?


Low beams are the outside lights, and the high beams on the inside. Remove the rubber cap. Squeeze the metal clip ends together and pull away from bulb. The bulb comes right out now. Disconnect the bulb from the harness of two wires. The bulbs are round with a flat side that faces up...it will not go in any other way. Do not touch the new bulb with bare hands, or oil with get on the glass and cause premature failure.

Jan 15, 2010 | 2007 Volkswagen Jetta 2.5 Sedan

1 Answer

Need to replace a headlight assembly for a 2006 Subaru Outback.


No, you just remove the radiator grill and the side marker light and the headlight housing bolts and it comes out. Not a real hard job and is Real straight forward. Good luck and have a good day.

Mar 27, 2009 | 2006 Subaru Outback

Not finding what you are looking for?
2005 Mazda 3 Logo

405 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

78919 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...