Question about 2005 Chevrolet Impala

1 Answer

My speedometer reads speeds beyond 120 MPH when I am stopped. It gradually creaps up sometimes while driving. If I turn the ignition switch on and off several times it will graduall return to 0 and work correctly for a while.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chevrolet Master
  • 5,763 Answers

Gm had problems with that cluster, the most problems where with the impala and malibus, sometime they even get stuck at top speed even with car off, some of them can be reprogramed but others had to be replaced, ive done a few,call your dealer and ask if theres a recall in your area, good luck.

Posted on Dec 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1995 c280 Mercedes-Benz can not run beyond 120 speedometer, once I try to go beyond 120 speedometer it will start cutting fire pls can anyone help me


Cars produced in Germany are electronically speed limited to about 150 mph. This is embedded in the software. If there are no other problems with the engine, fuel or transmission it is possible the management system has been remapped and the speed limiter has been reset to 120 mph.

Sep 04, 2016 | 1995 Mercedes-Benz C-Class

1 Answer

Speedometer not working


my speedometer will work every now and then but most the time it will read all the way up to 120 mph or stay at the wrong speed its not the speedometer or the dashboard cluster that's been checked out its a 2007 Pontiac Torrent FWD 5 speed transmission and it runs great. What do you think it could be?

Jan 04, 2014 | 2002 Pontiac Grand Prix

1 Answer

Obd2 system rediness status won't clear so I can run the smog test due to replacing the battery.


takes a long time to run the rediness test since there are 6 different tests to complete...

PROCEDURE 1
EVAPORATIVE EMISSION SYSTEM LEAK MONITOR
Inspection Conditions
Engine coolant temperature: 30°C (75°F) or less (The engine is stopped before the test drive is started).
Atmospheric temperature: 5 - 30°C (41 - 113°F).
Condition of A/T: Selector lever D range.
Fuel remained in fuel tank: 30 - 50% is recommended.
Time required: 16 minutes or less after started the engine.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position. Well be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 89 km/h (55 mph) or more and travel for 16 minutes.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position.

PROCEDURE 2
FUEL TRIM MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or less.
Atmospheric temperature: -10 - 60°C (14 - 140°F).
Condition of A/T: Selector lever D range.
Time required: 30 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 89 km/h (55 mph) or more and travel for 30 minutes.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 3
CATALYTIC CONVERTER MONITOR
Drive Cycle Pattern
Inspection Conditions
Atmospheric temperature: -10°C (14°F) or more.
Condition of A/T: Selector lever D range.
Engine coolant temperature: Not set.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 89 km/h (55 mph) or more.
Travel for 300 seconds or more while keeping the vehicle speed at 89 km/h (55 mph) or more.
Decelerate until the vehicle speed is within 80 km/h (50 mph) or less.
While traveling at 56 - 80 km/h (35 - 50 mph) for 10 minutes or more, fully close the throttle at least once in 2 minutes and decelerate for 10 seconds or more.
Do not repeat deceleration too often.
Vehicle speed may go below 56 km/h (35 mph) after the deceleration.
Stopping and braking are permitted. (If stopped or drive at 56 km/h (35 mph) or less for more than 5 minutes the monitoring may be stopped. In this case please restart monitoring from the beginning.)
After completing the above deceleration, bring the vehicle speed back to 56 - 80 km/h (35 - 50 mph) and keep it in the range until starting the deceleration again.
Repeat the above deceleration at least 5 times.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 4
HEATED OXYGEN SENSOR MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or more.
Atmospheric temperature: -10°C - 60°C (14 - 140°F) or more.
Condition of A/T: Selector lever D range.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 56 - 80 km/h (35 - 50 mph).
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 56 - 80 km/h (35 - 50 mph) and travel for 16 minutes or more.
Stopping and braking during this operation are permitted. Keep the accelerator opening degree constant for 1 minute or more after each acceleration.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 5
EXHAUST GAS RECIRCULATION (EGR) SYSTEM MONITOR
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature: 100°C (212°F) or less.
Atmospheric temperature: 5 - 60°C (41 - 140°F).
A/C switch: OFF.
Condition of A/T: Selector lever D range.
Time required: 16 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start.
Accelerate until the vehicle speed is 56 - 80 km/h (35 - 50 mph).
While traveling 16 minutes or more at 56 - 80 km/h (35 - 50 mph) with engine speed 2,000 r/min or above, fully close the throttle at decelerate for 5 seconds or more until the engine speed reaches 1,000 r/min or under.
Do not repeat deceleration too often.
Stopping and braking are permitted (Rapid deceleration and sharp steering are not permitted).
After completing the deceleration, bring the vehicle speed back to 56 - 80 km/h (35 - 50 mph) and keep it in the range until starting the deceleration again.
Repeat the above deceleration at least 8 times by fully closing the throttle valve.
Return the vehicle to the shop, then turn the ignition switch to "LOCK" (OFF) position

PROCEDURE 6
OTHER MONITOR (Main Components, Sensors & Switches, Wire Breakage & Short Circuit)
Drive Cycle Pattern
Inspection Conditions
Engine coolant temperature:
100°C (212°F) or less (Except engine coolant temperature sensor monitoring).
30°C (86°F) or less (Engine coolant temperature sensor monitoring).
Atmospheric temperature:
5°C (41°F) or more (Except engine coolant temperature sensor monitoring).
-10°C (14°F) or less (Engine coolant temperature sensor monitoring).
Condition of A/T: Selector lever D range.
Time required: 21 minutes or more.
Drive cycle pattern: One trip monitor (from start to ignition switch to "LOCK" (OFF) position). Will be completed while traveling with the following drive cycle pattern.
Test Procedure
Engine: start
Accelerate until the vehicle speed is 56 km/h (35 mph) or more.
While keeping the accelerator pedal opening degree constant, keep the vehicle speed at 56 km/h (35 mph) or more and travel for 16 minutes or more.
Return the vehicle to the shop.
After stopping the vehicle, continue idling for 5 minutes, and then turn the ignition switch to the "LOCK" (OFF) position. Moreover, the vehicle should be set to the following conditions for idling.
A/C switch: OFF
Lights and all accessories: OFF
Transmission: Neutral

Sep 15, 2010 | 1998 Mitsubishi Eclipse

2 Answers

My speedometer on my 2004 chev tahoe reads 120 mph. Sometimes it is less but is never the correct speed I am going. What do I need? A cable or fuse??


First call your dealer. There is a free instrument cluster replacement recall, which may apply for your problem.

May 15, 2010 | 2004 Chevrolet Tahoe

1 Answer

Why does my 03 yukon xl speedometer gradually flats to 0 while driving. it does not stall. it does it at least 1 a month specially in long trips or high speeds. when i arrive to destination it cools off...


It is probable that the cable for the speedometer is streached and your MPH reading is incorrect all or most of the time, get a friend to drive behind you at say 55 MPH so you will know the odometer reading ( may prevent speeding ticket )
All metal expands when heated and contracts as it cools. Your cable becomes slack when hot. Stay Safe!

Aug 25, 2009 | 2003 GMC Yukon XL

3 Answers

Both speedometer & tachometer not working, both reading wrong.


There was a recent class action law suit settled with GM for this exact problem. You can google gm speedometer lawsuit and get lots of information. Unforutunately for most people I think the warranty was limited to 7 years and 70,000 miles. Which isn't a lot of miles for most people.

If you car isn't covered by the warranty there is a way to "reset" the speedometer.

You can turn the ignition slowly like you are going to start the engine. There is a very small "dead" space where you will see your guage lights go off.

What you want to do is cycle the ignition switch from off to that dead space. Each time you do it your stuck speedometer will move towards zero about 10 mph. So if its stuck on 40 you will have to cycle it at least 4 times.

At first you will probably actually hit the ignition and the engine will try to start.....just release it and try it again.

I know this because I have a 04 avalanche with 80,0000 miles and it has this problem about twice a month.

Jun 02, 2009 | 2004 Chevrolet TrailBlazer

1 Answer

2003 Camry Speedometer reads 150 mph constantly.


i would disconnect the battery again let it sit for 15 minutes, i changed an alternator and jumped the car then started driving and that happened to me, 20 minutes of driving and the computer finally kicked in and started working again. good luck

Aug 17, 2008 | 2003 Toyota Camry

2 Answers

Speedometer stopped working


replace speed sensor

Jul 01, 2008 | 2004 Ford F150

Not finding what you are looking for?
2005 Chevrolet Impala Logo

210 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

80339 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...