Question about 2000 Chrysler Grand Voyager

1 Answer

Could you tell me were is the heater fan resistor pack located on my chrysler grand voyager

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 143 Answers

I have a chevy truck and my plug to my fan plugged into the fan and the resistor on the other end does it look like there is a short plug the to the fan

Posted on Dec 13, 2009

Testimonial: "I THINK THIS MUST BE A DIFFERENT HEATER ON MY VECHICLE, CHEERS FOR THE INFO."

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Heater wont blow on 2000 voyeger


Are you saying blower /fan not working at all? Checked fuses, and resistor?

Feb 10, 2014 | 2000 Chrysler Grand Voyager

1 Answer

A/C heater blower will not work


Locate and Test the Blower resistor pack. It is located in the blower box.

Dec 07, 2013 | 1992 Plymouth Grand Voyager

2 Answers

I have a 2000 chrysler grandvoyager se and it 's got a problem the air conditioner only works in full speed how can i fix this problem


There is a blower resister,module ,it is bad,it is located near the blower motor,mounted on the outside of the blower case,but actually goes inside the blower box to keep cool,most of the time the blower motor is the cause for the resister to go out,the blower draws too many amps,even though it may seem it is fine,this is the cause for the resister failure.

Apr 23, 2010 | 2000 Chrysler Grand Voyager

1 Answer

Where physically is the blower motor resistor located for 2000 Chrysler Grand Voyager? Checked underneath glove box but underneath is encased in plastic. Need to remove plastics?


open hood, at right side of vehicle underneath wiper module, at firewall, no need to remove wiper module.let me know if this help

Nov 19, 2009 | 2000 Chrysler Grand Voyager

1 Answer

The fan blower only works on high. The other


its the resistor, and its located with the blower motor. you will need a new motor assy. .......in Chryslers infinite wisdom, its all one unit.

Oct 08, 2009 | 1998 Plymouth Voyager

2 Answers

2000 Grand Voyager front A/C works off and on, back works good


check the condensor for debris, also check the front blower fan an its resistor, and again check your freon level

Aug 24, 2009 | 2000 Chrysler Grand Voyager

1 Answer

AC FAN WORKING INTERMITTENTLY


There is a fuse, but the heater motor (A/C) usually also runs some other things, but it is cheap to change the fuse and see what happens. More likely is the fan speed resistor pack. It isn't the easiest thing to find, but it is usually located in the air duct someplace under the dash. Does it do the same thing on all speeds, or just on one speed? If it does it on all of the speeds, then its more likely the fuse or the motor. If it only does it on one of the fan speeds or 2 out of 4 speeds, then the resistor pack is more likely.

May 20, 2009 | 2001 Chrysler Voyager

1 Answer

Location needed for blower senser on 99 plymouth voyager


the blower resistor is under the hood at the firewall on pass side... there are no screws just tabs holding it in place... the pigtail is usually needed when the resistor goes bad it melts the harness

Feb 12, 2009 | 1999 Plymouth Grand Voyager

7 Answers

Heater Control Switch Only Works on High


Your problem is probably a part called the heater resistor block or board. When this part burns out you will only have high speed on the fan. On my 1999 voyager it is located on the firewall and it snaps in a hole in the firewall. This is under the hood behind the alternator.
Mine had a multi pin black plug plugged into it. Unplug the plug and
you should be able to pull the block out insert new block and plug plug back in and it should come to life.

Jun 05, 2008 | 2001 Chrysler Voyager

Not finding what you are looking for?
2000 Chrysler Grand Voyager Logo

165 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

Marvin
Marvin

Level 3 Expert

83096 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...