Question about 1994 Saab 900
New saab 9000-1995-new to us. radio codes we figured out. BUt now as cd or radio plays, there is a beep every 3 seconds. It took a wrong code, worked with the on/band buttojn help. Is ther a way to force it to give you the code on screen. tried bttery and fuse??thanks--ron & peggy
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: 1999 Saab 900 radio reset code
whenever the battery is removed (or car experiences any loss of power) you must type in security code for radio (this is the case with BMWs and Volvos as well). Go to any saab dealership and they can remove the radio and get your radio's 4 digit code, they all have one. Yes, I have done this before ` they didn't charge me and I was in and out in ten minutes.
Posted on Jan 04, 2009
SOURCE: washer fuse blowing
OK guys. How cold is it where you are, and do you have
1. headlight washers as well
2. The right mix of screenwash/ water for your system
If not, check that you washer bottle has not frozen, blocking the pump and causing a system overload.
Also, check that the headlight washers (if they pop up from the bumper) are not frozen to the bumper body (it doesn't take much - try warming them with a hairdryer).
Posted on Jan 12, 2009
SOURCE: Radio code for 1997 saab 900s
I'm afraid if you don't have the code, you will have to take it to a local dealer or specialist radio store to have it re-coded.
Fortunately, it's not expensive.
Posted on Feb 24, 2009
1. Remove the battery.
2. Remove the clutch cable end from the clutch arm end at the wire stop.
3. Slide out the rubber doughnut from the gearbox housing which holds the clutch cable
4. Move the distribution box nut and the alarm pin attached to it (some modules)
5. Disconnect the clutch cable holder from the fender and the data link holder.
6. Remove the drivers lower panel below the steering wheel and remove the air duct as well as the knee shield.
7. Slide out the fuse box holder and ICE Box (should be a black box with many wires going to it). You can remove the instrument cluster at this point but you can also do this without removing the cluster with a little patience
8. Move the pedal spring to one side and remove the eye catch for the cable.
9. Remove the clutch cable by pulling it out from the engine compartment
10. Reinstall in the reverse. Saab actually came out with a bulletin which Needed one to install two washers at the back of the new cable instead of one. The factory cable comes with one but you can remove the 2nd washer off the old cable and install it on the new cable so two exist. This helps take up excessive pedal slack.
Posted on Apr 29, 2009
Tips for a great answer:
Jan 14, 2016 | Saab 95 Cars & Trucks
Apr 24, 2015 | 2003 Saab 9-3
Dec 22, 2017 | 2004 Saab 9-3
Feb 22, 2013 | 1996 Saab 900
May 26, 2011 | 1992 Saab 900
Apr 11, 2010 | 1998 Saab 900
May 19, 2009 | 1994 Saab 900
Sep 10, 2008 | 1994 Saab 900
Sep 09, 2008 | 1994 Saab 900
98 people viewed this question
Usually answered in minutes!