Question about 1996 Chrysler Town & Country

1 Answer

I can't find the speed sensor on my 1996 town and country

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Chrysler Master
  • 22,413 Answers

Look on top of the diff unit

Posted on Dec 12, 2009

Ad

3 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
short shadey
  • 421 Answers

SOURCE: location of the speed sensor on 1996 town & country

they are on the front drivers side of the transmisson and have two wires coming off them, there are two one is an input shaft sensor and the other is an output shaft sensor unless you have a 4 cyl van then there is only one sensor please rate -jeff

Posted on Sep 04, 2008

heavymetal77
  • 721 Answers

SOURCE: Transmission input output speed sensors

The speed sensor is on the tailshaft of the transmission,on the passenger side of the car,it has 3 wires. The output sensors are located on the front of the transmission about mid-way up the housing & only have 2 wires. Note the output sensors are not responsible for vehicle speed. Only the output shaft speed is recorded. They are for finding the correct cvi(clutch volume index) only. If you have a cvi issue,the transmission is toast.

Posted on Jun 26, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the speed sending unit located on a chrysler town and country


transaxle has two speed sensors input speed sensor located behind transaxle cooler lines the output sensor located far right transmission case driver side.

Jan 04, 2013 | 2002 Chrysler Town & Country

1 Answer

How locate and replace the speed sensor on 2000 town and country


Input shaft speed sensor or output shaft speed sensor?

Jul 01, 2010 | 1996 Chrysler Town & Country

1 Answer

Will not shift into third gear


you need to have three sensors checked that let the transmission shift up,
input sensor,output sensor and speed sensor

Jan 12, 2010 | 1996 Chrysler Town & Country

1 Answer

My 1996 town and country wont shift..It was shifting but then would stop but if we pulled over and re started it it would shift fine again. But now it isnt shifting at all..We have a computer hooked for it...


we can here,
your van is going into "limp mode"
when the computer does not get a correct signal from transmission it will not shift because it doesn't know your speed or engine RPM,
Three sensors on the transmission will trip it into limp mode,
1= output sensor,
2=input sensor,
3=speed sensor,
if you have it checked and get a "P0000" type code
it will tell you which one

Dec 18, 2009 | 1996 Chrysler Town & Country

1 Answer

Could a bad 02 sensor affect shifting in my 1996 chrysler town & country? When I started having problems I put a scanner on it, and the only code it put out was for a oxygen sensor. Could the 02 sensor...


Yes, the car will probably shift harder (if it has an automatic transmission) and it won't shift correctly when you try to accelerate at speeds over 30 MPH (it will downshift too many gears).

Nov 01, 2009 | 1996 Chrysler Town & Country

1 Answer

1996 CHRYSLER TOWN & COUNTRY TRANS AXLE PROBLEM.


i had same toublre on 96 plymouth output speed senor my wont shift out of second

Dec 06, 2008 | 1996 Chrysler Town & Country

1 Answer

Location of the speed sensor on 1996 town & country


they are on the front drivers side of the transmisson and have two wires coming off them, there are two one is an input shaft sensor and the other is an output shaft sensor unless you have a 4 cyl van then there is only one sensor please rate -jeff

Jun 17, 2008 | 1996 Chrysler Town & Country

Not finding what you are looking for?
1996 Chrysler Town & Country Logo

Related Topics:

117 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

Marvin
Marvin

Level 3 Expert

83772 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22413 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...