Question about 1992 Toyota 4Runner

1 Answer

92 4runner left side brights not working. Just replaced the lamp. I need a schematic

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Governor:

    An expert whose answer got voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 111 Answers

Check your locale discount parts store for a repair manual covering your suv. Diagrams are in the manual and some Libraries have on line access to manual data. Some suv's have a separate fuse for each low and high beam for each side of vehicle. Check that first. Then check for ground connection on the left lite to fender or chassis.

Posted on Dec 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

98 buick century. Brake lights and headlights not working, but 3rd brake light is. No bli kkers or 4 ways. Need schematic or a good idea where to look. Thanks


http://ibb.co/bWSoNS

Click on the link. This is for stop lamps, Your lower brake lamps are wired through the multifunction switch. The high-mount brake lamp isn't wired that way.
At the rear, stop lamps, right side, dark green wire is voltage for stop lamps, black wire is ground. For the left rear, stop lamp, yellow wire is voltage, black is ground.
At the moment, I think your multifunction switch is faulty?

Apr 17, 2018 | Buick Cars & Trucks

2 Answers

Why doesn't passenger side brake light work?


Either your bulb is out or there is a bad connection somewhere. Usually in the socket. Clean up the connections if needed.

I’m happy to assist further over the phone at https://www.6ya.com/expert/kim_3202917d7c587455

Oct 22, 2015 | 2005 Jeep Liberty

1 Answer

Why does my rear signal lamp not work


lots of times these things can be cleaned by cleaning contacts. I use contact cleaner and the put electric grease on them, work your way back to the fuse panel. might just find the problem is there. a relay could also be the problem. a good schematic will help. these problems are day long work out an slow. but I dont think it is a major serious thing just follow the circuit path.

Feb 01, 2015 | Cars & Trucks

1 Answer

2004 Jeep Liberty left tail light, left front parking light, and license plate light not working. Replaced all bulbs and number 7 fuse. Any ideas?


sure, do you have 12vdc to the lamp, in park?
if not work to the source , the relay that the operates that.
alldata.com has the schematic.

fact 1, license plate feed runs off left park.
fact 2, the park relay feed both left and right park fuses and lamps.
so, fuse 7 is left, and fuse 9 is right.
did you only just look at the fuse, and proclaim, good.
or use a voltmeter? or use ohms to test fuse 7, oops
fuses that look good, can be bad. 0 ohms good, infinity is bad.

use volts, is there 12vdc on both sides if fuse 7,>?
yes, then fuse is good, parks turned on.
no, the output side of fuse 7 is 0v. so fuse is blown
if input is dead, the relay is bad, but how can it , if right works, answer.
it cant be bad.
so what is the voltage all the way from the fuse to the lamps.
id bet, (fuse good an voltage good at fuse 2 sides) that the line is open. cut wire, corroded connector.

the BCM turns the relay on, this part works.
so.... its just a break in this simple copper path.

use a voltmeter, it will not lie to you, trust it./

Apr 05, 2014 | 2004 Jeep Liberty

1 Answer

Turn signals went out


replace the fuses first. for turn/hazards.
the HAZ fuse 10 amps ., do hazards fail?????????


old car, very old. 1980 corolla.
first off, the lamps are brass based lamps. 115x lamps
they can short so replace them all or remove all of them
and put only 1 new lamp in (of the 4) if this works, good.
if not use a voltmeter to find the cause.
12v during a flash is good, 0v dead, 6v is shorted wires.
this is easy, dont panic, get the schematic for the car is best way.
The FSM has this but are rare for such and old car.

i looked online , alldata.com
and the schematic is there.
the path is from battery to ground as follows
10a haz fuse and 5am turn fuse. (2 fuse!)
the fuses drives the HAZ module
the HAZ module drives the lamps directly in HAZ mode
in blink mode the HAZ module drives the combo turn switch.
a bad flasher module KILL BOTH, (did it?)
the comb drives left or right side and the lamps are all grounded
completing the path of electrics, and the lamps glow.
current flows, and the lamps glow.

lamps
green-black is left
green-yell is left side.

the best test for this car, is to cycle the HAZ button over and over
until they work, most switches this old. 33 years are dirty and fail.
so cycle it. 10 times, if the HAZ fails.
it must work on HAZ or its all a wasted effort.
because the HAZ module feeds the binkers...




Jan 20, 2014 | 1980 Toyota Corolla

1 Answer

I have a 97 suzuki sidekick and tailights work on and off right side works then stops working then left side works and licence plate light doesnt work at all i believe its a ground but dont know where to...


ok the full wiring is online, need that, a real FSM? for 1996 , same as 97
but not same 4sp tranny. i got confused, but seems the tail(parking) lamps are dead. you turn the Head lamps 1 click and some lights are dead.
there are a huge number if lamps in this circuit. Front and rear corners, all side lights x4, and dash maps, cig, lamp , ash tray lamp. radio lamp. shifter lamp (A/T) . and lic. plate.
for sure its wiring, if any lamp gloes, fully the HL (head light ) switch is good. so the wiring is bad to those lamps. the left rear has the trailer connector behind left rear Tail lens. see that. is it molested?
inspecting all 4 corners of care usually reveals collision damage , and
wires never repaired. you can use a volt meter to find this easy, have one?

Apr 09, 2013 | Cars & Trucks

1 Answer

2005 Jeep Liberty Sport. Headlights. Passenger Side is dim


TEST
remove both bulbs from the lamps but leave them on their wires switch on and see if the bulbs are still different brightness if not they the passenger side lamp housing has damaged mirror is dirty or missalined and needs adjustment. if they are different brightness then this may be a earthing problem.


Nov 13, 2009 | 2005 Jeep Grand Cherokee

1 Answer

What would I look at if my lights are very dim on both sides when their on regular. But on bright, the left side doesnt work at all & the right is working on bright perfect? Would it be the...


If the lights are dim, you'll need to check the ground for the front lamps. The ground is G101 ( #3) and is located on the left front of the radiator support.


742342.gif
tif.gif

Sep 05, 2009 | 2001 Chevrolet Impala

1 Answer

Right side will not work light glow only


If you have a service vehicle soon light (not service engine soon) this usually indicates a problem with the foreward lamp system.Your problem seems confusing, but check your high beam lamp operation. These cars are NOTORIOUS for corroded harnesses to the headlights. The problem is usually buried behind the washer bottle or across the radiator area. If you are lucky, it may be a burned out high beam bulb. If the blue symbol for brights stays on and there is no click when pulling on high beam lever, you will need a new turn signal switch.

Jun 21, 2009 | 2004 Chevrolet Cavalier

2 Answers

Headlight one side works on bright the other side works on dim


Try swapping the headlight bulbs or buying a known good bulb and testing that way. Sounds like a shorted bulb filament issue.

Apr 05, 2009 | 2004 Oldsmobile Alero

Not finding what you are looking for?
1992 Toyota 4Runner Logo

109 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

Marvin
Marvin

Level 3 Expert

81285 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...