Question about 2001 Ford Escape

2 Answers

3.0 ford escape no power to cylinder 4 & 6 i have changed the coils

Posted by on

  • diaz8440 Dec 12, 2009

    changed wiring harness and tried four different sets of plugs and also the ecm.

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 2 Answers

Hey Diaz8440:

Did you ever resolve this? I have the EXACT same symptom. #6 and #4 are DEAD! New, plugs, coils, PCM, injectors.

I ran some tests and proved it wasnt electrical and it wasnt injectors. Compression looks good.

I saw a post at www.iatn.com where some mechanic had the same exact issue.



That site, www.iatn.com, however, is reserved ONLY for professional mechanics. They wont let us in to see the answer. I am suspicious that there is something peculiar going on here with this issue.

Please advise if you ever resolved this. It's my son's car and after it melted two CATs I now have 2K tied up in it. I am past the point of giving up. I MUST fix it!

Thanks,

Robb

rmurdock@luxortech.com

Posted on Jun 14, 2010

Ad
  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 430 Answers

Try changing the plugs and wires on these 2 cylinders

Posted on Dec 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to fix ford escap 2002 v6 missing 4&6cilander


if that is what code your getting from computer scan ,most likely its a coil pack gone bad ,one way to check is to change one with one from an different cylinder 1, 2,3,5, and see if misfire codes change to those cylinders ,if it does replace those.coils. coils cost about 50.00 new

Sep 09, 2014 | 2002 Ford Escape

1 Answer

04 escape has code 354,356,300,316


Possible Bad COP Ignition Coils on #4 & #6 cylinder

Forget the 300 & 316 of no use to you

PO 304 is the same as PO354 or letter D
PO 306 is the same as PO356 or letter F

If the codes are the actual bad coils -you won't have to pull
the upper intake off

Dec 04, 2012 | 2004 Ford Escape

1 Answer

02 ford escape #4 and #6 missfire


does 4 & 6 run off same coil? if so i would look at that coil or wireing to that coil

Jun 16, 2012 | 2002 Ford Escape

1 Answer

My 2005 ford escape v6 is only firing on cylinder 1 and 6


Your an 2005 Ford Escape 3.0L, you don`t have a distributor. Each cylinder has it`s own coil and is controlled by the PCM. You need to scan the PCM to determine which cylinder is loosing power ( misfire). P0301 cylinder #1, P0302 Cylinder #2 and so on. The coils are common problems with this vehicle, but pay close attention that the drivers in the PCM are not at fault. #1 cylinder is on passenger side near the firewall passenger compartment. firing order as follows, Bank #1 1-2-3 front of engine to rear. nearest the passenger compartment. I`m an ASE Master with 30 years experience. Be careful, don`t waste money on unneeded parts! I own my own company. 805-369-4589 Jerry Bryant. Advise is free, but like reading a diagnostic manual does not mean the problem is solved. Correct diagnoses and system inspection and testing is what needs to be done so you don`t waste money!

May 11, 2012 | 2005 Ford Escape XLT

2 Answers

05 Ford Escape, coils #3 & #4 not firing. We've replaced the battery, spark plugs, alternator, coil packs, & pcm. Had pcm reflashed. Garage said it had to be coil packs, but just replaced coil packs 3


Check engine light on ? Code's ? What engine ? 2.3 l 4cylinder or 3.ol v-6 This vehicle has coil on plug ignition system , not coil packs ! a coil per cylinder . If new coils an still has no spark , has no B+ voltage to the coil or the PCM isn't controlling them . Without testing i'd only be guessing as to the problem .If the repair shop you had it to can only say it had to be the coils , I'd find another shop to take it to !
Autolite Coil on Plug Ignition troubleshooting

Jun 22, 2017 | Cars & Trucks

1 Answer

On my 2003 Ford Escape 3.0L VIN 1 I have the following codes, PO316,305,306,300,304. Are these codes caused by a possible vacuum leakl? If so what would be the likely spot?


Forget the 300 & 316

The 304,305 &306 are ignition coil codes for
#4 ,#5 ,#6 cylinders

Doubt you have more than 1 bad coil

Check for Vacuum Leaks -- they wouldn't
help any, but are the cause of 80% of all
O2 Sensor Codes.

You may luck out & if any coils are bad, you won't
have to remove the upper intake (this time around)

You will get at least one bad coil a year on all fords

Have the intake manifold Smoke Tested with an EVAP
Smoke Machine,for leaks

Jul 03, 2011 | 2003 Ford Escape

1 Answer

Misfire #4 p0304 engine is sluggish.rough idle at times


Check the coil, a good test is to change the coil with another cylinder and see if the misfire moves to that cylinder, if it moves then you will know its the coil make sure to mark it so you know which one to replace, this is very common for coils to go bad, heres a diagram to help you locate #4 cylinder.couldnt get diagram but if its a four cylinder then #4 is the last one back if its a 6 cylinder then it will be the first cylinder on the driverside .first cylinder from the front to rear,

Dec 12, 2010 | 2005 Ford Escape

2 Answers

Just bought a used Ford Escape 2001 and the "check engine light is constantly on. Diagnostic tests reads malfunctioning cylinder #4. What does this mean and what is involved in getting it fixed?


might be something as simple as changing the spark plug or related wire, could also be damadge to the valve train or piston and cylinder bore

Oct 27, 2010 | 2002 Ford Escape

Not finding what you are looking for?
2001 Ford Escape Logo

Related Topics:

294 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

79077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

fordexpert

Level 3 Expert

5677 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...