Question about 2003 Chevrolet Venture Passanger

1 Answer

When I put my van in reverse, it will stall... while it is in park, I can touch the wireing that goes into or behind the air box it will stall.. I need to know if it is the wiring harness or the silver box what looks to be a computer

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 106 Answers

This is probably a bad connection in the wiring harness. If you disconnect the computer and use a wire-piercing self powered test light, you may be able to identify one or more wires in the harness that are intermittent, and repair them by adding a jumper across the damaged portion(s). The computer is inside the air box for cooling, and therefore sometimes is subject to excess humidity. It could also be the plug itself that is loose or corroded. If there is any green or white crust on or in the plug, clean it thoroughly with battery cleaner, dress it with dielectric grease, and reconnect. Any wires that seem loose in the plug during this process probably are. Sometimes you can bend the contacts SLIGHTLY to correct this. Reinforcing the plug where the wires come out of it using silicone adhesive may also help.

Posted on Dec 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Stalls when put into drive or reverse


Your idle air controller may be failing. Begin checking for stored codes using a code reader, and progress to standard troubleshooting steps such as checking spark, fuel delivery, and operation of the intake air control circuit.

May 11, 2015 | 1994 GMC Sierra

1 Answer

Transmission for 1999 cara van


did you check the fluid in the transmissin it could be low or also it could need a new transmission filter i wouldnt try to drive it it anymore without checkin or changin it because it will burn it up

Feb 16, 2013 | 1999 Dodge Grand Caravan

1 Answer

I have a 1996 ford 350 van it has a 5.8 engine in it, My problem is when I start it ,It fires right up after a few cranks but if its in park it will idle high and then stall out or if it been running for a...


Take it to AutoZone for a free diagnostic scan. Your local Ford dealer will charge you $100+ for the same scan.

It sounds like the idle control valve and/or the mass air flow sensor. The scan will accurately pinpoint the problem.

Jun 01, 2012 | 2002 Ford E350

2 Answers

I have a 95 town and country the gauges are not reading correctly the oil pressure reads really high when driving for about 10 minutes then levels out I just had an oil change my fuel gauge will sometimes...


If the check engine light is not on, stay away from sensors for now. First when is the last time you have had a tune up? PLugs , wires, air and fuel filter. Stalling at a stop can be from the air filter, fuel filter (clogging up), It can also be from the catalytic conveter, these also clog up. It can be from vacuum leaks, this usually has a rough idle also. It wouldn't hurt to check for codes, intermittant codes don't always pop the light on. On some vehicles the o2 sensors can cause a rough idle and stall at stops, ut they usually set a code/ light.

Jul 19, 2011 | 1995 Chrysler Town & Country

1 Answer

I have a 1999 dodge ram 1500 truck conversion van


hi your problem is the electric fuelpump in the tank after replaceing it try not to let the truck get below a quarter of a tank on fuel as this will cause overheating of the pump and premature failure of the pump. don

Jun 24, 2010 | Dodge Ram 1500 Cars & Trucks

1 Answer

My wife came to a stop while driving the van. When she went to take off she pushed the gas and there was a loud boom followed by a severe whining noise. The reverse gear worked so she got the van out of...


The wheels turning opposite is normal. It's how the differential works. You need to get the transmission checked out by a qualified tranny person.

Apr 08, 2010 | 1999 Ford Windstar

1 Answer

My revirse lights do not work


Really dont need to know color of wire for this system is simple. On the switch (left rear corner on transmission) there are three wires. one wire is power, one allows it to start in park or neutral and the other is for the reverse lights. If I remember correctly the two outer terminals operate the reverse lights. Find the power lead and jump to each of the other two to determine which is for the reverse lights. Likely you will find that the switch is bad and there is no wiring problem. Make sure that reverse lights have good grounds as well.

Aug 16, 2009 | 1987 Dodge Ram Wagon B250

1 Answer

How do I install a new starter in a 93 Dodge Ram van B-250 8 cyl.


Park van so that you can safely access the starter. I use ramps under front wheels and put it in park and set the parking brakes. Disconnect positive battery cable at battery, disconnect starter battery cable and ignition wires from starter solenoid (remember terminal locations as these will attach to new starter solenoid). Remove old starter. Replace with new starter. Re-attach wiring in reverse order.

Mar 26, 2009 | 1993 Dodge Ram 250

1 Answer

Stalling & high idle 2002 Honda Odyssey


vacuum leak..look to area behind air cleaner to intake .. snorkel area first..spray carb cleaner there after you start it to discover vacuum leak.... this is a guess .. but a good one... check first for hoses off/ leaking intake air sources and let me/us know

Nov 24, 2008 | 2002 Honda Odyssey

Not finding what you are looking for?
2003 Chevrolet Venture Passanger Logo

82 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

78919 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...