Question about Ford Aspire

1 Answer

We just had the wheel bearing/hub fixed by a shop on a 97 ford aspire and now the brake pedtal is going to the floor. we were told that we needed brakes when we picked up the car but having no brakes is a different story.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 430 Answers

Bad brake booster.....if u r sure that brake pads were fine

Posted on Dec 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I get the rear drums off a 2000 Ford focus. I removed the spindle nut,


2000 Ford Focus Drum Removal ProcedureIf removing the drum to service the rear brakes: (note, do not remove hub retaining nut for this procedure)
1. Raise and support vehicle
2. Release the parking brake
3. Remove wheel and tire
4. Disconnect wheel speed sensor wiring harness from wheel knuckle and floor panel.
5. Remove 4 wheel spindle attaching bolts, then the wheel hub and drum assembly from vehicle.
6. Reverse procedure to install noting the following:
a. Torque wheel spindle retaining nut to 49 ft. lbs.
b. Torque wheel/tire assembly to 94 ft. lbs.
2000 Ford Focus Drum Replacement ProcedureIf replacing the drum and wheel bearing assembly:
1. Raise and support vehicle
2. Release the parking brake
3. Remove wheel and tire
4. Remove center dust cap.
5. Remove hub retaining nut.
6. Remove drum and hub assembly. Ensure wheel speed sensor ring is not damaged when removing drum/hub (if equipped).
7. Reverse procedure to install noting the following:
a. Inspect and clean wheel speed sensor ring if equipped.
b. When tightening hub retaining nut, rotate the hub assembly in counterclockwise direction.
c. Torque hub retaining nut to 173 ft. lbs.
d. Torque wheel/tire assembly to 94 ft. lbs.
e. Adjust parking brakes as necessary.


Jul 05, 2011 | 2000 Ford Focus

1 Answer

Im looking for front left hub for ford focus 2lt 2001 but i couldnt find it can you help me find it and if possible where i can download the part picture thanks


The hub is the part the tire bolts to. The hub sits inside of the wheel bearing. The wheel bearing is pressed into the knuckle.

If you looking to replace the hub than you will need to remove the tire/wheel, the brake caliper, the brake rotor, the axle nut, separate the lower ball joint from the knuckle, separate the outer tie rod from the knuckle, remove the strut to knuckle bolts, push the axle out of the hub and remove the knuckle from the vehicle.

The knuckle will then need to be brought to a machine shop or a shop capable of pressing the old bearing out and pressing the new bearing in. You will ruin the bearing once you press the hub out of the bearing so if you need to replace the hub than you will need to replace the bearing at the same time.

The hub is the part on the upper left. the bearing is the part on the upper right.

airjer995_7.jpg

Nov 21, 2010 | Ford Focus Cars & Trucks

1 Answer

How do you remove the Hub and Rotor on a 97' F250 with Auto 4 wheel drive? I can not get the rotor to come off. I know that the hub must come with it. However, I am not sure what I have not removed in...


Section 05-03C: Wheel Hubs and Bearings, Front Wheels, 4-Wheel Drive 1997 F-250/350/Super Duty Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 05/17/2000 Locking Hubs, Manual

e9801b.gif


Item Part Number Description 1 3A329 Halfshaft 2 3C132 Rolling Diaphragm Seal (Axle) 3 3299 Integral Spacer Needle Bearing Seal 4 3123 Bearing, Caged Needle 5 3105 Front Wheel Spindle 6 1190 Wheel Hub Grease Seal 7 4221 Inner Wheel Bearing (with Bearing Cup 4222) 8 1102 Front Disc Brake Hub and Rotor 9 4221 Outer Wheel Bearing (with Bearing Cup 4222) 10 - Pin (Part of 1195) 11 1195 Inner Lock Nut 12 1198 Lockwasher 13 1197 Outer Lock Nut 14 - Steel Thrust Washer
(Part of 3B458) 15 - Plastic Thrust Washer
(Part of 3B458) 16 - Splined Thrust Washer
(Part of 3B458) 17 3B457 Snap Ring 18 1K105 Hub Body 19 - Lock Ring (Part of 1K106) 20 1K104 Cap 21 1K104 Capscrew A - While Rotating Front Disc Brake Hub and Rotor, Tighten Inner Lock Nut to 68 Nm (50 Lb-Ft) to Seat Bearings. Back Nut Off 90 Degrees (1/4 Turn). B - Tighten to 217-278 Nm (160-205 Lb-Ft) C - Tighten to 4-6 Nm
(35-53 Lb-In) Removal
  1. Separate cap assembly from hub body by removing the three Torx® head capscrews.


    de0460a.gif



    de0285a.gif

  1. Remove the lock ring seated in the groove of the front disc brake hub and rotor (1102).


    f4658c.gif

  1. Remove the hub body assembly from the front disc brake hub and rotor. If the body is difficult to remove, install two capscrews and pull the body assembly out of the front disc brake hub and rotor.


    f4659d.gif

Installation
  1. NOTE: Do not pack the hublock body assembly or cap with grease. Excessive grease can cause excessive dialing effort and hub failure.

    Follow removal procedure in reverse order.
  1. Tighten three Torx® head capscrews to 4-6 Nm (35-53 lb-in).

Oct 04, 2010 | 1997 Ford F250 SuperCab

1 Answer

Change rear wheel bearing is it hard to do ford fusion 03


Lightly losen the lug nuts with the tires on the the ground. Jack up the car and remove the tire according to the owner's manual. Make sure to block the wheels. After the tire is removed, release the park brake. Support the car on jack stands. Remove four bolts from the rear of hub. The hub nut will be 29 mm - it is important that you have a tight fit if you attempt to remove the nut.

At this point you MAY have to loosen or remove the remove the emergency brake cable. Either way the hub is ready to be removed. The front of the hub (with the lugs) and the bearing will come out and the back plate and brake shoes will remain in place.

Once you get it off, you may either purchase a hub assembly (which includes the hub with a new bearing in place ready-to-go) or take the existing hub and a replacement bearing to an auto machine shop which can easily remove the old bearing and install the new bearing. Using extreme care you can remove the old one using bearing pullers and prybars and replace the bearing using large deep sockets or a properly sized piece of steel pipe.

Since you have the hub apart, you should inspect the brake shoes and (brake) wheel cylinders and replace them as needed. Replace brake parts on both sides if you replace them on either.

Put the hub back into the brake shoes. It may only line up one way. Finger tighten ALL FOUR of the bolts and then tighten. Replace the tire and remove the lifting equipment. Start slowly so the brakes can readjust!

Sep 17, 2010 | 2004 Ford Focus

1 Answer

Since my front struts were replace, I've had this rubbing sound coming from my front end. I've had my brakes and struts checked (by the shop that did the replacement) and have been told there's nothing...


Rubbing noise or grinding? Is it louder going around corners? It sounds like it could be the wheel bearings, and if it is indeed the wheel bearings, then yes, you need to get them replaced asap. Wheel bearing failure can cause the wheel to come off of the vehicle, hub and all.

Feb 04, 2010 | 2002 Chevrolet TrailBlazer

1 Answer

Rear Shoe Replacement 97 ford aspire


you have to set theself adjuster to the fully released position .place a suitable tool against the adjuser cam and push it to the released position. in stall brake drum .pre load wheel bearing . pump brakes several times to set the self adjuster.

Apr 04, 2009 | 1996 Ford Aspire

1 Answer

Need to replace the front left wheel bearing on a 2003 escape two wheel drive v6, how do i get the bearing out?


You need to remove the tire, brake caliper and rotor. Remove the axle nut and hub bolts. Take the hub (bearing is pressed in it) to a machine shop to have new bearings pressed in.

A mechanic will usually charge around 300 dollars per bearing (cost included).

Jul 25, 2008 | 2002 Ford Escape

1 Answer

1996 ford f250 4 wheel drive truck


Item Part Number Description 1 N800794-S60 Bolt, M16-2.0 x 50 2 N601797-S2 Bolt, Caliper Mount M12-1.75 x 30 3 2C150 Pin Assembly 4 2C357 Disc Brake Caliper 5 1175 Seal 6 3423 Bearing 7 3105 Front Wheel Spindle 8 4221 Differential Bearing 9 4222 Differential Bearing Cup 10 1190 Wheel Seal 11 1102 Front Disc Brake Hub and Rotor 12 1102 Front Disc Brake Hub and Rotor 13 1197 Locknut 14 1B198 Lockwasher 15 1C245 Thrust Washer 16 35704 Dana Nut 17 2K004 Front Disc Brake Rotor Shield 18 2B292 Anchor Bracket 19 3130,
3131 Steering Knuckle9572fc0.gif

Jun 11, 2008 | 1996 Ford F250 Crew Cab

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

131 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

78936 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

fordexpert

Level 3 Expert

5676 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...