Question about 2004 Mercury Sable

1 Answer

I drive a 2004 mercury sable, what is the symptoms of a car having problem with the cam sensor and synchronize.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Thanks for checking on me. I found the answer to my question to confirm the car symtoms.

Posted on Dec 13, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Symptoms 1996 sable po500 code


speed sensor failure

Symptoms of a P0500 DTC may include
: loss of anti-lock brakes the "anti-lock" or "brake" warning lamps on the dash may be lit the speedometer or odometer may not work properly (or at all) your vehicle's RPM limiter may be decreased the shifting of an automatic transmission may become erratic other symptoms may also be present

Read more at: https://www.obd-codes.com/p0500
Copyright OBD-Codes.com

Oct 15, 2016 | 1996 Mercury Sable

1 Answer

My fuel rail sensor low code (P193) shows. If the sensor is actually bad, what are the engine symptoms?


if the fuel rail pressure is low then the main symptoms are random misfiring and lack of power on acceleration

Jan 01, 2014 | 2004 Mercury Sable

1 Answer

My fuel rail sensor code comes up. What are the engine's symptoms is the sensor is bad?


The computer uses this signal to help optimize engine performance and drivability. Without it, it could run rich , run lean or go into limp mode, reducing engine performance for protection.

Jan 01, 2014 | 2004 Mercury Sable

1 Answer

2003 Sable engine change


check the location of the cam position sensor. if they are in the same place ,then use all the sensors from the old motor

Jan 09, 2013 | 2003 Mercury Sable

1 Answer

Problems with Mercury Sable 04/ stalls, engine light stays on


Could be crank shaft sensor, plus fuel filter tune up plugs and wires, go to auto zone check light it is free.

Jul 22, 2017 | 2004 Mercury Sable

1 Answer

Replacing camshaft position sensor, Sable 2003,Ohv


usually if the magnet in the sensor comes out it destroys the cam position shaft,(it should have a half moon shape when u remove the sensor from the cam pos/oil pump drive. if the half moon is damaged or missing u must replace the cam pos/oil pump drive, and yes it is timed with the engine. wot i have done is try to locate where the half moon was on the drive it usually leave a trace of where it was. now index where the half moon is at remove hold down bolt and remove the driver assy. install the new drive, clock the half moon shaft to match the one u just removed once u get the half moon shaft where u want it and the oil pump rod alines and the whole housing is down install the hold down clamp. now to get rid if that check engine lite youll have to plug a scanner in and look at the live data adjust the cam position till u have plus or minus 2 degrees

Mar 18, 2010 | 2003 Mercury Sable

1 Answer

My 1996 Mercury Sable GS wont start. Turns over fine got gas just won't fire


sounds like you could have a bad crank sensor or maybe even a cam sensor if these are ok then id check the coil pack.

Dec 11, 2009 | 1996 Mercury Sable

1 Answer

2000 Mercury Sable double overhead cam Transmission problem


manual para reparación cadena de tiempo de motor v6 3.0 sable 2000

Oct 18, 2008 | 2000 Mercury Sable

3 Answers

1996 mercury sable speed hand and drives in strain and ****


I hace a 19196 sable-the problem is the transaxle speed sensor-this part sends all speed info to the computer ..-First symptom(speedometer stops working and then transmission shifts erratacially and power steering becomes hard and engine light comes on..The computer on this all eletronic car cannot send proper signals to the speedo-trans-power steering and other functions without knowing how fast or slow the car is going..Have the SPEED SENSOR mounted on top of the tranaxle replaced and all will be well.Part is not to expensive.labor can vary depending whether you have 3.0OHV or DOHC engine-some cars have to have exhaust dropped to get at it-Good Luck All

Jun 17, 2008 | 1996 Mercury Sable

Not finding what you are looking for?
2004 Mercury Sable Logo

Related Topics:

203 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

gerry bissi

Level 3 Expert

4387 Answers

Marvin
Marvin

Level 3 Expert

83096 Answers

fordexpert

Level 3 Expert

5690 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...