Question about 2003 Ford Focus

1 Answer

FITTING NEW TIMING BELT HOW DO I TIME IT UP on ford focus zetec 1.6 se 03

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Ford Expert
  • 279 Answers

You need a setting kit which consists of a twin cam locking bar and a crank locking pin
autodata have a full step by step guide of the replacement procedure

Posted on Dec 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Replace broken timingbelt


What engine does yours have ? 2.0l Zetec ? You need special tools !

May 31, 2015 | 2000 Ford Focus

1 Answer

Timing Diagram of 2000 Ford Focouse DOHC 2.0 Zetec


If you Blew off the timing belt then need Head work also since it is an interference Motor
meaning that the Valve train and Pistons Have no Clearance so U are going to need a lot more work than just a timing belt to run

Mar 31, 2014 | 2000 Ford Focus

1 Answer

HAVE TO RESET THE TIMING ON A FORD FOCUS ZETEC SE 1.6 WHERE IS THE CRANK SHAFT LOCATION FOR THE TIMING PIN?


As you look at engine from timing belt side by where the drive shaft runs at back of engine around four inches back there is a small 10mm bolt that goes into the engine block undo this and that is where the pin goes don't forget that the crank pulley gear is free wheeling so make sure you use a new crank bolt and use correct torque setting

Sep 06, 2013 | 2003 Ford Focus

1 Answer

1.8 zetec timing belt snapped is it non interferance


I have a 2003 focus, And timing belt slipped, Knackering up all the valves, Tried a new timing belt, Left with no compression, Will be scrapping it next week

Feb 27, 2012 | 2000 Ford Focus

1 Answer

I have a 2000 ford focus 2.0 zetec dual overhead cam with a broken timing belt at low speed. Is this engine a non interference engine?


all Zetec engines (2.0 DOHC) are NOT interference engines. There are deep reliefs cut into the top of the piston to clear the valves when they are fully extended. There will be no valve damage if the timing belt breaks on a Zetec engine.

Oct 29, 2009 | 2000 Ford Focus

1 Answer

Focus timing belt replacement.


This is a very very easy timing belt setup. first off you have to remove the valve cover. Then you have to remove the serp belt. Then remove anything thats in your way of the front cover. after you remove the crank pulley re-install the crank bolt. DO NOT LOSEN THE BOLT FOR THE TENSIONER!!!! now spin the crankshaft until the sproket aligns with the timing mark. now at this point the two camshafts should be aligned. now there is a special tool from ford that holds the cam shafts in place. all it is is a 1/4" peice of metal that goes on the left side of the cam shafts to hold them into place. if you mark the cams you wont need the tool. or if you can find something to fit in the left side of the cams that will work too. anyways after that its just the same steps in reverse. very easy to do.

Aug 29, 2009 | 2002 Ford SVT Focus

2 Answers

Air bag light keeps coming on in ford focus 03 plate zetec 1.6 wa


Common fault on FORD
Usually due to a poor connection in the YELLOW PLASTIC CONNECTOR underneath the passenger seat.


Just push it together properly and it should clear the AirBag fault


Apr 08, 2009 | 2003 Ford Focus

2 Answers

Cam belt or timing chain ?


Dont know for pos, but almost all new cars have timming belts. except for v8s and a few v6s

Jan 06, 2009 | 2000 Ford Focus

Not finding what you are looking for?
2003 Ford Focus Logo

471 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

81285 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

gerry bissi

Level 3 Expert

4376 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...