Question about 2005 Chevrolet Suburban

1 Answer

Front fan switch only works on speeds 1, 4 and 5. Any ideas on how to fix?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

  • Expert
  • 61 Answers

Its called bower control modular,needs to be replace,,

Posted on Dec 13, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Fan speeds 1 and 2 are not working but speeds 3 and 4 are...any ideas?


Possible that the rheostat or the multiswitch has some contact problems.You must have an access to the switch settings to measure any outward voltage to the fan.If there is no voltage then the switch is defective.If there is contact then the controller is defective and is not reacting to the set point.

Sep 02, 2010 | 2006 Jeep Liberty

1 Answer

A/C has quit working on fan speeds 2 thru 4.....it will only work on speed 1 but the fan itself still works on all speeds...it just seems to kick the a/c off on speeds 2 thru 4 and blow hot air ....2001...


You probably have a bad fan switch. I had the same issue and had it diagnosed and replaced. It fixed the problem, but it seems to be coming back less than 2 years later.

Jul 08, 2010 | 2001 Mazda Protege

1 Answer

Fan motor on a 2000 Chevy Malibu only works on 3-5 and not on 1 & 2. How to fix?


Its the blower motor resistors or the switch itself.
You need shop manual. Then remove the switch and jump certain terminals with a jumper wire to see if fan runs at certain speeds. If fan runs at all speeds when jumped then the switch is your problem . if it runs at the speeds you described in your write up then its the resistors.

Jun 04, 2010 | 2000 Chevrolet Malibu

1 Answer

Fan on c3 will only work on no 4 setting 1 2 3 not working any ideas


these systems use a resistor pack,setting 1 2 3 go through resistors to vary fan speed, 4 is fast speed-- no resistor in circuit. don't know where it is located but usualy in aplace it can get cool air, try follow the wires back from the fan motor to the switch.

Feb 08, 2010 | 1983 Chevrolet K1500

1 Answer

Town and country mini van


does it turn off when the car turns off? if so, you probably need a new blower motor resistor. They run about $80 but shop around. Fixed my problem right away

Jun 04, 2009 | 2002 Chrysler Town & Country

3 Answers

Heat/AC Blower fan speed only works on High


Alot of people have the same problem with the fan switch and blown bulbs. There really is no fix for this. Jeep really screwed up when designing the heater control assembly. The cheapest solution is to buy another unit off Ebay. Can always go to the dealer but be ready to PAY for there mistakes.

Jan 14, 2009 | 2005 Jeep Grand Cherokee

Not finding what you are looking for?
2005 Chevrolet Suburban Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

83096 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...