Question about 2005 Peugeot 405

2 Answers

Peugeot partner wopnt start replaced glow plug

Peugeot partner wont start, replaced glow plug controller still not full voltage going to glow plugs with ignition on 2litre hdi

Posted by on

  • Anonymous Mar 16, 2014

    glow plugs wont start

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 4 Answers

What voltage u getting ?. did it just stop and then not restart. if its getting fuel and glow plugs are working the next two items id look at is the cam shaft and crank shaft position sencors. also make sure ur battery is in good condition, so starter motor is turning fast enough to build up the correct pressure on the rail.

Posted on Dec 14, 2009

Ad
  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

Wont start mornings glow plugs been changed &manual pump

Posted on Jan 27, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What voltage do i require to use NGK Y103V glow plugs in my Kaboto 3 cyl engine and will a simple push button type switch be adequate .


glow plugs on a diesel should be the same voltage as the battery voltage that vehicle has , the glow plug relay takes this power and allows it to go to glow plugs for first few minutes of starting , some of them cycle the power on/off several times a minute to control the temp of glow plug but the voltage is allways the power of the battery , this may only not be true on large trucks and tractors (im talkin big !) they use 36 volts to start but then as soon as started cut back to 12 or 24 volts

Mar 04, 2017 | Cars & Trucks

1 Answer

My peugot partner van T reg wont start when cold. Starts with easy start and when the engine is warm. spent hundreds of pounds on it, been to 3 garages and its still the same and now on top of everything...


sounds like a vacume leak this can stop cold engine from starting. vacuum leaks can be hard to find, it could be just about anywhere. when you have engine running spray the easy start or carb cleaner around the vacume lines, note any engine sound changes. and that will be where the problem could be, say could as it could have more than one leak.

Jul 26, 2017 | Peugeot Partner Cars & Trucks

1 Answer

Ford 03 6.0L Excursion wont start when cold


You need to start with your glow plug circuit. There is a glow plug module that is the most likely culprit. You need to get a circuit tester and when the another person turns the key, you verify whether or not you have voltage to glow plug on the engine itself. If not the control module will have to be replaced. The glow plug control module is on the right hand side and front of the engine. Let me know what else you may need.

Mar 29, 2010 | 2003 Ford Excursion

1 Answer

Wont start battery low was changed


it sounds more like bad glow plugs. these heat the air in the cylinders to aide in cold starts and are controled by a temp sencing unit. with a volt meter or if your car is equiped with a gauge turn the ignition on. there should be a very noticable drop in your voltage. if not your glow plugs are probibly bad.

Jan 09, 2010 | 2004 Audi A6

3 Answers

Peugeot partner wont start first thing once


i presume its a diesel

i reckon its the glow plugs get them checked i am sure a new set will cure your problem

Nov 05, 2009 | 2006 Peugeot 604

1 Answer

Glow plugs causing starting problem


if you need connectors and terminals for the glow plug connections under the valve cover, Ford sells then so you don't need a whole $600 harness.

info for your use

Section 03-07B: Glow Plug System 1996 F-250, F-350, F-Super Duty Equipped with 7.3L Diesel Engines Workshop Manual
DESCRIPTION AND OPERATION Glow Plug System The 7.3L diesel engine uses a glow plug system which preheats air in the combustion chamber to improve cold engine starting. The system consists of eight glow plugs, the glow plug control module (12B533), powertrain control module (PCM) (12A650), engine oil temperature (EOT) sensor and barometric pressure sensor (BARO sensor) (12A644). The glow plug system is electronically controlled by the powertrain control module. The powertrain control module energizes the glow plugs immediately after the key is placed in the ON position and then determines how long the glow plugs will be on according to the engine oil temperature and the barometric pressure. The required time for the glow plugs to be energized decreases as the engine oil temperature and barometric pressure increase. The glow plugs are self-regulating, and the powertrain control module controls relay ON time. The powertrain control module protects the glow plugs by energizing them for short durations if the battery voltage is abnormally high.

Possible Causes: Insufficient glow plug ON time will not allow enough heat to accumulate in the combustion chamber to easily facilitate starting. If the glow plug system ON time does not meet any of the specifications in the accompanying chart the problem is most likely a faulty wire harness connection, ground connections or glow plug relay.

If the glow plug resistance to ground is high, the most likely causes are an open UVC (under valve cover) harness or open glow plug.
--------------------------------------------------------
Relay Operation
Install a DVOM on the glow plug feed side of the glow plug relay (large stud with two wires connected). Turn the ignition key to the ON position but do not attempt to start. Note the time in seconds from when the key is turned on and the glow plug relay energizes until the glow plug relay de-energizes. The glow plug relay makes a loud click noise which is easily heard when it energizes and de-energizes. The dome light will dim and the dash voltmeter will dip when the glow plugs are drawing current from the battery. Compare the times measured to the table (time will be affected by engine temperature, battery condition and vehicle altitude). The voltage at the glow plug feed terminal may vary from 9 to 12 volts depending upon battery condition.
--------------------------------------

-----
If battery voltage not present check for B+ at power supply terminal (terminal with single large wire). Power for glow plug power supply is supplied from starter relay through two fusible links at solenoid.
Glow Plug Operation
Disconnect all of the glow plug/injector harness connectors from the valve cover gaskets. With the pigtail installed, measure glow plug resistance to ground (preferably B-). A resistance measurement of .1 to 6 ohms indicates a good glow plug.



Glow Plug Harness Continuity
Measure for continuity from the connector harness to the glow plug feed terminal on the glow plug relay. Resistance should be less than 5 ohms.
Incorrect measurements will result if all glow plug/injector connectors to valve cover are not disconnected.

---------------------------------------------------
Glow Plug Relay The glow plug relay (12A343) has a plastic base and two mounting bolts. It is operated by the powertrain control module (PCM) (12A650) which senses engine oil temperature, PCM voltage and barometric pressure. When the engine oil temperature or the barometric pressure is low, the PCM activates the glow plug relay and the glow plugs. If the PCM voltage is too high, the powertrain control module deactivates the glow plug relay and the glow plugs immediately energize for a shorter duration, decreasing the modulation of the duty cycle.
-----------------------------------------------
Glow Plug Removal
  1. stj~us~en~file=ani_caut.gif~gen~ref.gif WARNING: THE RED-STRIPED WIRING HARNESS CARRIES 115V DC. SEVERE ELECTRICAL SHOCK MAY BE RECEIVED. DO NOT PIERCE.
    Remove valve cover (6582). Refer to Section 03-01D .
  1. Disconnect glow plug electrical connector using a pair of pliers.
  1. Remove glow plug using 10mm socket.
  1. Clean and inspect glow plug tip for damage. Replace if damaged.
Installation
  1. Install glow plug and tighten to 19 Nm (14 lb-ft).
  1. Connect glow plug electrical connector. Make sure glow plug wiring is routed to avoid moving parts.
--------------------------------------------------------------
Glow Plug Control Glow plugs are used to warm the cylinders to improve cold-engine starting. The PCM uses the engine oil temperature (EOT) sensor and barometric pressure (BARO) sensor to determine how long the glow plugs will be on. The PCM energizes the glow plugs longer if the engine is very cold or if the barometric pressure is low at high altitudes.
The PCM controls the relay that supplies power to the glow plugs with the glow plug control (GPC) signal. When the GPC signal is grounded by the PCM the relay closes, turning the glow plugs on.
The glow plugs are controlled by the following sequence:
  1. PCM energizes the glow plugs.
  1. The PCM energizes the glow plugs immediately after the ignition is placed in the ON position.
  1. The PCM then determines how long glow plugs will be on based on EOT sensor and the BARO sensor. The required time to warm up the cylinder decreases the engine oil temperature and barometric pressure increases at low altitudes.
Glow Plug Lamp Control The glow plug lamp (GPL) signal controls the WAIT TO START light located on the instrument panel. This light is used to indicate when to start the engine. The cylinders are being warmed by the glow plugs during and after this light is lit. The PCM energizes the glow plug lamp longer if the engine is very cold or if the barometric pressure is low.
When the GPL signal is brought low, the "Wait to Start" lamp is turned on.
The glow plug lamp is controlled by the following sequence:
  1. PCM lights the WAIT TO START light after a key on reset occurs.
The PCM determines the glow plug lamp activation time based on engine oil temperature, barometric pressure and battery voltage.
  1. PCM turns off the WAIT TO START light.
The glow plug lamp is turned off when the timer counts to the number of seconds specified by the PCM. The glow plugs will normally remain on longer than the "Wait to Start" lamp.
-----------------------------------

Mar 14, 2009 | 2004 Ford F350

2 Answers

Peugeot Partner Van 51 Plate


HI,AS IT IS HARD TO START THESE EXTRA COLD MORNINGS WE ARE GETTING,TRY A SET OF GLOW PLUGS, YOU CAN SEE THEM ACROSS THE FRONT OF THE CYLINDER HEAD,WITH A WIRE JOINING THEM UP,YOU WILL NEED A 8mm SCOKET , FOR THE WIRE, AND A DEEP 12mm ONE FOR THE PLUGS,UNSCREW TO THE LEFT,AND PUT A BIT OF GREASE ON THE THREAD OF THE NEW ONES AS THEY CROSS TREAD EASY,ABOUT 17POUNDS FOR A SET,THANKS.

Jan 03, 2009 | 2006 Peugeot 604

Not finding what you are looking for?
Cars & Trucks Logo

1,173 people viewed this question

Ask a Question

Usually answered in minutes!

Top Peugeot Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

mike hayward

Level 2 Expert

279 Answers

Wahs Team

Level 2 Expert

215 Answers

Are you a Peugeot Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...