Question about 1994 Jeep Grand Cherokee

1 Answer

Serpentine belt tensioner

Serpentine beltnsioner location

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Novelist:

    An expert who has written 50 answers of more than 400 characters.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

  • Expert
  • 94 Answers

If you have 4l inline6, there is no tensioner on it. you adjust the belt via alternator. On the V8, you'll find him on the pass. side in front of the cyl. head.

Posted on Dec 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How simple is it to change a alternator belt on subaru svx?


  1. Removing the Serpentine Belt
    • 1 Park your Subaru on a level surface and open the hood.
    • 2 Disconnect the ground (black) battery cable using a wrench. This will prevent the cooling fan from activating.
    • 3 Locate the serpentine belt routing diagram in your engine compartment and compare it to the actual routing of the installed belt. Make sure the routing on the label matches the actual routing. If they do not match or there is no label, note the actual routing on a piece of paper for later reference.
    • 4 Locate the belt tensioner pulley on your Subaru model. If the tensioner is equipped with a squared hole, use a large breaker bar with a 1/2-inch (13 mm) drive. Otherwise, use a ratchet and socket of the proper size on the tensioner pulley center bolt.
    • 5 Rotate the tensioner pulley away from the belt to release the belt tension.
    • 6 Pull the belt off of one of the pulleys and slowly release the tensioner pulley back into position. Do not let the tensioner pulley snap back or you may damage an internal component.
    • 7 Finish removing the serpentine belt from the rest of the pulleys and the engine compartment.
    Installing the New Serpentine Belt
    • 1 Match the old belt to the new one and make sure they are of the same length and configuration. It is normal for the new belt to be slightly shorter since the old one has been stretched through use.
    • 2 Route the new serpentine belt through all of the pulleys except the tensioner pulley. Use the diagram on the engine compartment or your notes, as a reference, to properly route the belt.
    • 3 Insert the large breaker bar into the square hole or the ratchet and socket into the tensioner pulley center bolt.
    • 4 Rotate the tensioner pulley in the same direction you did to release the belt tension.
    • 5 Slide the serpentine belt onto the tensioner pulley.
    • 6 Release the tensioner pulley back into position.
    • 7 Look at all the pulleys and make sure the serpentine belt is properly seated on each one. Otherwise, release the belt tension and adjust the belt.
    • 8 Connect the ground (black) battery cable using the wrench.

Oct 18, 2011 | 1992 Subaru SVX

1 Answer

Serpentine belt diagram for a 2003 Chevy unpalatable 4.3


Pop the hood of the car and locate the serpentine belt routing diagram. The diagram on the 2003 Chevrolet Impala is on top of the fan shroud. The diagram will be a picture of all of the accessory pulleys and how the serpentine belt is routed among the pulleys. This diagram will give you the exact direction for routing the new belt onto the pulleys. If you cannot find a serpentine belt routing diagram, take a notepad and pen and draw out the exact routing diagram of the old belt across the pulleys.

  • 2 Locate the serpentine belt tensioner. It is located below the alternator on the left front side of the engine. The tensioner on the 3.4 liter, 3.5 liter and the 3.9 liter engines will require a 3/8 ratchet to release the belt tensioner. The 3.8 liter engine will require a ratchet and a 15 mm socket for the belt tensioner. Rotate the belt tensioner clockwise to loosen and remove the belt from the belt tensioner pulley.
  • 3 Slide the old belt from the belt tensioner pulley. Remove the belt from the remaining pulleys and pull the belt from the engine compartment.
  • 4 Route the new belt across the crankshaft pulley first. The crankshaft pulley is the big pulley on the bottom of the engine in the center. Then route the serpentine belt across the remaining pulleys as directed by the serpentine belt routing diagram. Leave the belt tensioner pulley for last.
  • 5 Rotate the belt tensioner clockwise again to relieve the tension and slide the new belt across the top of the belt tensioner pulley. Release the belt tensioner and the belt will tighten up as the tensioner applies pressure to the belt. Make sure the new belt is properly seated in all the pulleys.
  • 6 Crank the engine and inspect the belt again to make sure that it stays seated in the pulleys.

  • Read more: How to Replace a Serpentine Belt on a 2003 Chevrolet Impala ' eHow.co.uk http://www.ehow.co.uk/how_6120665_replace-belt-2003-chevrolet-impala.html#ixzz1Yi6QLAjb

    Sep 21, 2011 | 2003 Chevrolet Impala

    1 Answer

    Instructions needed for changing serpentine belt on 2002 Ford Windstar 3.8L


  • the serpentine belt routing chart, adhered to the fan shroud. This chart will show you the location of the belt tensioner.
  • 2 Pull the belt tensioner off the belt with the serpentine belt tool. Reach in with your free hand and slip the belt out of the tensioner's path and then slowly move the tensioner back into position.
  • 3 Pull the belt off the remaining pulleys by hand


  • Read more: 2002 Ford Taurus Serpentine Belt Removal ' eHow.com http://www.ehow.com/how_7233863_2002-taurus-serpentine-belt-removal.html#ixzz1XPRa20xf

    Sep 09, 2011 | Ford Windstar Cars & Trucks

    1 Answer

    How do i release the tension belt ... cant seem to find bolt being referred to in other docs


    Here's the procedure on how to release and replace the tension belt of your car.

    Step 1
  • Open the hood on the Volvo S-60 and find the serpentine-belt routing diagram. The diagram should be attached to the top of the fan shroud that covers the radiator. If not, draw out the exact routing method of the serpentine belt around each pulley with a pen and a piece of paper.
  • Step 2 Locate the serpentine-belt tensioner that is in the very center of the engine. The tensioner will have a square bolt head in the center of the tensioner pulley.
  • Step 3 Slide the open end of the 5/8-wrench onto the square bolt head in the center of the belt-tensioner pulley. Turn the tensioner pulley counterclockwise and slide the serpentine belt off of the tensioner pulley.
  • Step 4 Remove the serpentine belt from the other pulleys and pull the belt out of the engine compartment.
  • Step 5 Slide the new serpentine belt into the engine compartment and around the crankshaft pulley.
  • Step 6 Route the new serpentine belt around each pulley. Turn the belt-tensioner pulley counterclockwise again and slide the serpentine belt around the tensioner pulley. Release the tensioner and it will tighten the belt around the pulleys. Look over the belt to ensure that it is inside of each pulley.
  • Step 7 Crank the S-60 and look over the serpentine belt with the motor running. Let the engine run for about one minute and shut the engine off. Close the hood.
  • Aug 12, 2010 | 2001 Volvo S60

    1 Answer

    Serpentine belt broke on 87 ford econo van


    ps...you do not have to Post another Question....just Add a Comment to this question.

    "HOW TO": I professionally prefer the Serpentine Tensioner Tool.
    Standard Rules to Removal the Serpentine Belt with an Automatic Tensioner:
    1. Find the Tensioner(s).
    2. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (located on the Tensioner Pulley rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
    3. Remove the loosened belt off one of the other more easily accessed Pulleys.
    4. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.

    Standard Rules for Installing the Serpentine Belt with an Automatic Tensioner:
    a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
    b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
    c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley and Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
    d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
    e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them.

    Apr 15, 2010 | 1987 Ford Econoline

    1 Answer

    Replace serpentine belt on 1992 dodge grand


    Click on the following free direct Link.
    It has the correct Belt Diagrams for your 1992 Dodge Grand Caravan wirh either the 3.0L SOHC V6 or the 3.3L V6.

    http://www.2carpros.com/car_repair_information/year/1992/make/dodge/model/grand_caravan/1992_dodge_grand_caravan_drive_belt_routing_diagram.htm


    Included on the Diagrams are the Instructions on "Rotating" the Automatic Tensioner. See Below for additional Instructions to make your job easier.

    "HOW TO": I professionally prefer the Serpentine Tensioner Tool.
    Standard Rules to Removal the Serpentine Belt with an Automatic Tensioner:
    1. Find the Tensioner(s).
    2. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (located on the Pulley or Arm Base) OR the OPENING (3/8ths or 1/2 inch square opening located on the Tensioner Arm) rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
    3. Remove the loosened belt off one of the other more easily accessed Pulleys.
    4. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.

    Standard Rules for Installing the Serpentine Belt with an Automatic Tensioner:
    a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
    b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
    c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley/Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
    d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
    e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them.


    Before You GO:
    Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!

    Apr 11, 2010 | 1992 Dodge Grand Caravan

    1 Answer

    Cannot get the serpentine belt back on


    "HOW TO": I professionally prefer the Serpentine Tensioner Tool.
    Standard Rules to Removal the Serpentine Belt with an Automatic Tensioner:
    1. Find the Tensioner(s).
    2. Using a Serpentine Belt Tensioner Tool, Or Wrench OR Ratchet, Rotate/Move the Tensioner USING THE AVAILABLE NUT (located on the Tensioner Pulley rotating the Tensioner Pulley/Arm - moving it away from contact with the belt and towards the area where the belt is not in contact with the Tensioner Pulley. The Tensioner is spring loaded, and is hard to rotate/move.
    3. Remove the loosened belt off one of the other more easily accessed Pulleys.
    4. DO NOT quickly release the Tensioner, but gently allow the Tensioner to rest in its closed position.

    Standard Rules for Installing the Serpentine Belt with an Automatic Tensioner:
    a. Pick a Pulley that is most easily accessed. This will usually be on top. This will be the last Pulley that the belt will go on.
    b. Using the Diagram: Install the new Serpentine Belt on the remainder of the Pulleys....over, under, left right.
    c. Using a Serpentine Belt Tensioner Tool or Wrench or Ratchet Tool: Rotate/Move the Tensioner Pulley and Arm "away" from Belt contact area on the Tensioner. This spring is pretty hard and with a new belt, it will be even harder to install. Rotate/Move this to as-close to the maximum allowed inorder to have enough slack in the belt to get it up and over the last pulley.
    d. Using your other hand - Pull the Belt up and over the Last remaining Pulley.
    e. Before releasing the pressure on the Tensioner, visually inspect the remainder Pulleys and the Belts' Positioning on them.


    Before You GO:
    Let me know if this helped, or if you have additional information questions. Feel Free to contact me at FixYa.com!

    Apr 10, 2010 | 1999 Jeep Grand Cherokee

    1 Answer

    I need to replace the idler pulley/tensioner and the belt


    When this idler wears out it makes a growling noise that changes with engine RPM. A Bad Idler Pulley May Wobble & Wear Out Your Serpentine Belt Prematurely. Get Rid Of That Horrible Noise & Change.

    Remove the serpentine belt by using a breakover bar, ratcher or serpentine belt removal tool with the correct size socket for the pulley mounting bolt. Rotate tensioner arm to release tension. Remove the bel. Using the proper size socket, remove the tensiones mounting bolt and remove tensioner.

    Before installing the new tensioner, make sure the mounting surface for the tensiones is clean and free rust or other obstructions. Find the locator pin hole and rotate the replacement tensiones until the locator pin and the hole line uo. Insert the pin into the hole. Reinstall the mounting bilt and torque down to tight fit.

    Rotate the tensioner arm to install the serpentine belt. Make sure the belt is correctly fitted to all pulley in the drive system. Start the engine to check for any problems. Extreme care should be taken when reinstalling the serpentine belt because some of the pulleys are located in remote positions ans it is very hard to see that belt is seated properly in all of the grooves. If the belt isn't seated properly, the belt can "ride out" of the grooves and the belt can be damaged.

    Also must review the ZJ Repair Manual Secc-7-Cooling-System for graphics references.

    Hope helped with this. Remember rated this help. Good luck.

    Nov 26, 2009 | 1996 Jeep Grand Cherokee

    1 Answer

    How to change serpentine belt, 2004 Toyota Tundra


    locate tensioner pulley; release tension from belt; remove belt; make sure not to forget how the belt is routed; route belt around all pulleys but tensioner; put tension on tensioner pulley; route belt over tensioner pulley

    Oct 03, 2009 | 2004 Toyota Tundra

    1 Answer

    How do I locate tension wheel to replace serpntne belts 04 sentra


    The serpentine belt runs everyting under the hood...easiest way to locate the tension wheel is to look at every other wheel that the belt runs to.

    Your tension wheel will be where the belt runs without being in a V channel, the tension wheel will be flat..no grooves to accomodate the belt.

    Hope this helps

    Feb 01, 2009 | 2004 Nissan Sentra

    Not finding what you are looking for?
    1994 Jeep Grand Cherokee Logo

    Related Topics:

    235 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Jeep Experts

    Marvin
    Marvin

    Level 3 Expert

    83036 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22382 Answers

    Ronny Bennett Sr.
    Ronny Bennett Sr.

    Level 3 Expert

    6927 Answers

    Are you a Jeep Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...