Question about 1988 Nissan Pathfinder

2 Answers

Gday need a diagram of a 1987 pathfinder rear axel and diff

Posted by on

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 1 Answer

My pasword it not exepted from websaites

Posted on Dec 12, 2009

Ad
  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 117 Answers

Probly need to get the whole manual. Amazon can direct you to the right store to do this.

Posted on Dec 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is diff unit


a diff unit is short for differanchial gear,ie gearbox main drive or in a rear wheel drive the big round thing in the middle of the rear axel.adrian

Mar 15, 2011 | 2000 Hyundai Elantra

1 Answer

What releases the rear axels from the differential, to change the axel seals on the backer plate.96 yukon.


remove the pot cover and drain, remove the bolt that holds the center diff pin in, then remove pin,AT THIS POINT DO NOT TURN ANYTHING AXLES OR DIFF OR DRIVESHAFT push axle inward and remove u clip that holds shaft in then pull shaft out

Oct 29, 2010 | 1996 GMC Yukon

1 Answer

Diagram for 1987 rear end monte carlo how to add rear end oil


there is a recessed fill plug on the nose of the diff housing (faces front)

Aug 21, 2010 | 1987 Chevrolet Monte Carlo

1 Answer

Differential oil leak. oil showing near driveshaft, and both axel areas. i understand that the diff seal is by the driveshaft. any ideas on why thee would be oil on the areas of the diff housing by...


The rear axle seals are leaking too,it's been my experience with Dodge 2500's,all 3 seals leaking is usually a indication that there are bearings going south!

Mar 10, 2010 | Dodge Ram 2500 Cars & Trucks

2 Answers

Huming noise in the rear axel. not sure which


This Rear Axel Has A BAD Rep For Failure and Mostly Wheel Bearingd Go First ,Then By the time they go Its too Late to Save the Whole Diff I Spent 2 Days LOOKING for a Replacement for a Customer. You May Get Lucky and JUST NEED WHEEL BEARINGS, FLUID LEVEL MUST be up To FILL HOLE PLUG.

Aug 01, 2009 | 1997 Jeep Grand Cherokee

1 Answer

How to replace my 1994 lincoln towncar rear axel seal


you need to pull the cover off the rear diff. remove the rear brake drums or rotors, remove the bolt that holds the pin in the rear end, remove the pin, remoce the c clips, pull the axles out. remove the seal. you can do this by using one ofthe axles to pry the seal out. install the new seal and reassemble. use rtv sealant to reseal rear diff and fill with about 3 - 3 1/2 qts gear lube-may take synthetic

May 23, 2009 | 1994 Lincoln Town Car

1 Answer

Rear Axel Seal Leaking, How do I pull the axel to repair?


You will need to remove the differential rear cover,drain fluid, remove wheel, brake drum, (rotor) . Unbolt center diff. pin, carefully remove (don't loose shims) push axle in remove lock keeper, then slide out axle, replace seal, put some grease on it, slide axle in reverse all to install.

May 22, 2009 | 1999 Jeep Grand Cherokee

2 Answers

Replacing the rear axles on my 1987 monte carlo


You will have to remove the rear end cover then turn over by hand you will see a metal pin going through the smaller spider gears in the center there should be a small bolt there with a 5/16 head remove the bolt and then the metal pin then push in ward on the axles and a c plip will fall out only do 1 side at a time and do not rotate the axles other wise the gears will fall out and you will have another problem.

Jan 07, 2009 | 1987 Chevrolet Monte Carlo

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

63 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

Marvin
Marvin

Level 3 Expert

83624 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22393 Answers

gerry bissi

Level 3 Expert

4387 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...