Question about 2004 Jeep Grand Cherokee

1 Answer

I have a 2004 Jeep Grand Cherokee that has a grinding noise ( almost like teeth on a gear trying to slip or just barely be touching ) in the rear of the veh when making sharp turns

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 73 Answers

Sounds like your spider gears are bad in your rear diff. common.. chrysler 8 1/4 diff..

Posted on Dec 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

2004 jeep grand cherokee new starter very loud


Only thought is, when you tighten the bolts ,go a little on
one ,then the other, like 3 times, don't tighten one all the way
first. Makes the housing warp.

May 04, 2013 | 2004 Jeep Grand Cherokee

1 Answer

2004 Jeep Grand Cherokee Limited makes rear noise when turning left?


Could be low on oil, or need a shot of additive if it is a limited slip differential.
The noise may be the clutches in the diff or one of the axle bearings.

Jul 26, 2012 | 2004 Jeep Grand Cherokee

1 Answer

Grinding and whinning noise suddenly coming from driver side rear end on my 97 Grand Cherokee Ltd 5.2 it is 4wd all the time. Only does this when moving in gear


Have differential(s) serviced. Ensure correct friction modifier is added to gear oil. I have this problem every 40-50 or so thousand miles.

Feb 26, 2011 | 1997 Jeep Grand Cherokee

1 Answer

94 jeep grand cherokee laredo V8 5.2l automatic. Drives fine but after 10-15 mins of driving After its parked it makes loud popping noise from the rear. Cant locate where the sound is exactly coming from....


You can check fluid level by removing the rubber plug in the cover. Fluid is full when on level ground, it is just at the edge of the hole (or very close) if you are already getting noises out of there, you can remove the cover and inspect gears for wear or breakage. If you find a large amount of metal debris in the lube it tells you something bad is going on back there. Although rebuildable, it's not a home job...requires exact settings in order to operate properly. You can find good units far cheaper than even a gearset costs in any scrapyard. to match ratio, count the teeth on the ring gear and the pinion gear. the replacement MUST have the exact same number. Before swapping diffs, check all back there to make sure noise is not from somewhere else.

Jun 20, 2009 | 1994 Jeep Grand Cherokee

1 Answer

We bought a 1995 jeep grand cherokee orvis edition...the truck will not go into reverse...it makes a wierd grinding noise


Be sure that the truck is fully engaged in two wheel drive. It may have slipped out of gear on the transfer-case. Move the lever for 2 and 4 wheel drive back and forth a few times before shifting transmission.Good luck

Apr 25, 2009 | 1995 Jeep Grand Cherokee

1 Answer

1996 jeep grand cherokee, quadra trac,, rear end making alot of noise simular to a bad tore bearing, could the rear end need replaced? thanx hohn the rear end makes a grinding sound as you drive down the...


Since you aready paid $400, go back to ;the shop and get your $'S worth!! Unless someone can prove that the axle bgs were bad, you shoulld ask why pinion & side gears were not diagonsed!!! (dosen't anyone test drive stuff after they "fix" something anymore??? Dosen't anyone give a damn???
If you can't get anywhere with this, find a junkyard unit and install it yourself. It isn't that hard. Just be sure that new lone has the same mount points and gear ratio matches ratio lof front axle.(count gear teeth if you must)

Feb 22, 2009 | 1996 Jeep Grand Cherokee

Not finding what you are looking for?
2004 Jeep Grand Cherokee Logo

Related Topics:

306 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...