Question about 1998 Chrysler Cirrus

1 Answer

Cap on fuel pump access leaks is there a o-ring or gasket there

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 265 Answers

You can just replace your gas cap...If you keep getting an emssions code,,its probaly because your gas cap isnt tight, or you have been filling up while the car is running..

Posted on Dec 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Emissions code is showing code po442. Cannot find any leaks. Already replaced gas cap. What is the other most obvious problem that can be fixed easily?


Common Problems That Trigger the P0442 Code
  • Defective or damaged fuel cap
  • Distorted or damaged Fuel Tank Filler Neck
  • Small tear or puncture in the Evaporative system hose(s) and/or Carbon Canister
  • Defective Fuel Tank Sending Unit gasket or seal
  • Small split in a seam of the Carbon Canister
  • Defective Evaporative Vent Valve and/or Evaporative Purge Valve
  • Defective or damaged Fuel Tank
  • Defective Fuel Tank Pressure Sensor
  • Defective Leak Detection Pump
  • Slightly loose and/or worn clamps or hardened O-rings anywhere in the EVAP system
Common Misdiagnoses
  • Fuel cap
  • Evaporative Purge Valve
  • Evaporative Vent Valve

Jun 05, 2011 | 2002 Ford Explorer

1 Answer

Can this code p0442 be the gas cap?


Common Problems That Trigger the P0442 Code
  • Defective or damaged fuel cap
  • Distorted or damaged Fuel Tank Filler Neck
  • Small tear or puncture in the Evaporative system hose(s) and/or Carbon Canister
  • Defective Fuel Tank Sending Unit gasket or seal
  • Small split in a seam of the Carbon Canister
  • Defective Evaporative Vent Valve and/or Evaporative Purge Valve
  • Defective or damaged Fuel Tank
  • Defective Fuel Tank Pressure Sensor
  • Defective Leak Detection Pump
  • Slightly loose and/or worn clamps or hardened O-rings anywhere in the EVAP system

Dec 30, 2010 | Toyota Avalon Cars & Trucks

1 Answer

Can I access the fuelpump through the trunk on a 94 concours c4.6


According to the instructions, it is not accessible through the trunk on the 94 Cadillac --- REMOVAL AND INSTALLATION Fig. 1: Fuel pump unit 8470h037.gif
  1. Disconnect the negative battery cable.
  2. Relieve fuel system pressure.
  3. Remove fuel filler cap to release fuel tank vapors. Leave cap off until repairs are completed. Gasoline fuel vapors are extremely flammable. Ensure that fuel is stored in a container that can be properly sealed. Never store fuel in an open container. Store container in a safe place away from heat.
  4. Remove fuel tank by performing the following:
    1. Step 1: Drain fuel from the tank into an approved container for storage.
    2. Step 2: Raise and safely support the vehicle.
    3. Step 3: Remove rear stabilizer bar at links, pivot bar downward.
    4. Step 4: Remove hoses and pipes from tank unit.
    5. Step 5: Remove hoses at tank from filler and vent pipe.
    6. Step 6: Disconnect tank unit harness from rear body harness.
    7. Step 7: Support fuel tank and disconnect 2 fuel tank retaining straps.
    8. Step 8: Remove tank from vehicle.
  5. Remove sending unit, gasket and pump assembly by turning cam lock ring counterclockwise. Lift assembly from fuel tank and remove fuel pump from fuel tank sending unit.
  6. Pull fuel pump up into attaching hose while pulling outward away from bottom support. Take care to prevent damage to rubber insulator and strainer during removal. After pump assembly is clear of bottom support, pull pump assembly out of rubber connector for removal. To install:
  7. Push fuel pump assembly into attaching hose.
  8. Install fuel tank sending unit and pump assembly into tank assembly. Use new O-ring seal during reassembly.
  9. Install cam lock over assembly and lock by turning clockwise.
  10. Support tank and position in vehicle. Install tank straps and secure with retaining bolts. Tighten to 25 ft. lbs. (33 Nm).
  11. Connect tank unit harness to body harness.
  12. Connect hoses to filler and vent pipes. Tighten clamps.
  13. Connect hoses and pipes to tank unit.
  14. Connect rear stabilizer bar to links. Tighten bolts to 42 ft. lbs. (58 Nm).
  15. Lower vehicle.
  16. Refill tank and install filler cap.
  17. Connect negative battery cable.
  18. Start engine and check for leaks.
prev.gif next.gif

Aug 26, 2010 | Cadillac Escalade ESV Cars & Trucks

2 Answers

I am getting no diesel into my fuel filter is their a electric pump in my tank or is the fuel pump part of the injector pump


Fuel Pump REMOVAL & INSTALLATION Navajo and B Series Pick-up Models NOTE: To gain access to the fuel pump, it is necessary to remove the fuel tank.
  1. Depressurize the fuel system and remove the fuel tank from the vehicle.
  2. Remove any dirt that has accumulated around the fuel pump attaching flange, to prevent it from entering the tank during service.
  3. Turn the fuel pump locking ring counterclockwise using a locking ring removal tool and remove the locking ring.
  4. Remove the fuel pump and bracket assembly.
  5. Remove the seal gasket and discard it. To install:
  6. Put a light coating of heavy grease on a new seal ring to hold it in place during assembly. Install it in fuel tank ring groove. Fig. 1: Fuel pump and sending unit used on the B Series Pick-up regular cab 89685g02.gif
    Fig. 2: Fuel pump and sending unit used on the B Series Cab Plus Pick-up 89685g03.gif
    Fig. 3: Fuel pump and sending unit used on the Navajo 89685g04.gif

  7. Insert the fuel pump assembly into the fuel tank, then secure it in place with the locking ring. Tighten the ring until secure.
  8. Install the tank in the vehicle.
  9. Install a minimum of 10 gallons of fuel and check for leaks.
  10. Install a pressure gauge on the throttle body valve and turn the ignition ON for 3 seconds. Turn the key OFF, then repeat the key cycle five to ten times until the pressure gauge shows at least 30 psi. Reinspect for leaks at the fittings.
  11. Remove the pressure gauge. Start the engine and check for fuel leaks.
MPV Models
  1. Relieve the fuel system pressure and disconnect the negative battery cable.
  2. Remove the rear seat and lift up the rear floormat. Remove the fuel pump cover.
  3. Disconnect the sending unit/fuel pump assembly electrical connector and the fuel lines.
  4. Remove any dirt that has accumulated around the sending unit/fuel pump assembly so it will not enter the fuel tank during removal and installation.
  5. Remove the attaching screws and remove the sending unit/fuel pump assembly.
  6. If necessary, disconnect the electrical connectors and the fuel hose and remove the pump from the sending unit assembly.
  7. Installation is the reverse of the removal procedure. Be sure to install a new seal rubber gasket. Fig. 4: Remove the rear seat and floormat to service the fuel pump 90975g06.gif
    Fig. 5: Removing the fuel pump assembly 90975g07.gif
prev.gif next.gif

Aug 17, 2010 | 1995 Mazda MPV

1 Answer

How to replace ford explorer fuel pump 1994


REMOVAL & INSTALLATION NOTE: To gain access to the fuel pump, it is necessary to remove the fuel tank.
  1. Depressurize the fuel system and remove the fuel tank from the vehicle.
  2. Remove any dirt that has accumulated around the fuel pump attaching flange, to prevent it from entering the tank during service.
  3. Turn the fuel pump locking ring counterclockwise using a locking ring removal tool and remove the locking ring.
  4. Remove the fuel pump and bracket assembly.
  5. Remove the seal gasket and discard it. To install:
  6. Put a light coating of heavy grease on a new seal ring to hold it in place during assembly. Install it in fuel tank ring groove. Fig. 1: Fuel pump and sending unit used on the Regular Cab Ranger pick-up 89685g02.gif
    Fig. 2: Fuel pump and sending unit used on the Super Cab Ranger pick-up 89685g03.gif
    Fig. 3: Fuel pump and sending unit used on the Explorer and Mountaineer 89685g04.gif

  7. Insert the fuel pump assembly into the fuel tank, then secure it in place with the locking ring. Tighten the ring until secure.
  8. Install the tank in the vehicle.
  9. Install a minimum of 10 gallons of fuel and check for leaks.
  10. Install a pressure gauge on the throttle body valve and turn the ignition ON for 3 seconds. Turn the key OFF, then repeat the key cycle five to ten times until the pressure gauge shows at least 30 psi. Reinspect for leaks at the fittings.
  11. Remove the pressure gauge. Start the engine and check for fuel leaks.
prev.gif next.gif

Jul 31, 2010 | 1994 Ford Explorer Limited

1 Answer

Is there an easier way to replace the fuel pump other than dropping the tank?


No, the fuel tank must be dropped if there is no access door (which there usually isn't for safety reasons).


REMOVAL & INSTALLATION NOTE: To gain access to the fuel pump, it is necessary to remove the fuel tank.
  1. Depressurize the fuel system and remove the fuel tank from the vehicle.
  2. Remove any dirt that has accumulated around the fuel pump attaching flange, to prevent it from entering the tank during service.
  3. Turn the fuel pump locking ring counterclockwise using a locking ring removal tool and remove the locking ring.
  4. Remove the fuel pump and bracket assembly.
  5. Remove the seal gasket and discard it. To install:
  6. Put a light coating of heavy grease on a new seal ring to hold it in place during assembly. Install it in fuel tank ring groove. Fig. 1: Fuel pump and sending unit used on the Regular Cab Ranger pick-up 89685g02.gif
    Fig. 2: Fuel pump and sending unit used on the Super Cab Ranger pick-up 89685g03.gif
    Fig. 3: Fuel pump and sending unit used on the Explorer and Mountaineer 89685g04.gif

  7. Insert the fuel pump assembly into the fuel tank, then secure it in place with the locking ring. Tighten the ring until secure.
  8. Install the tank in the vehicle.
  9. Install a minimum of 10 gallons of fuel and check for leaks.
  10. Install a pressure gauge on the throttle body valve and turn the ignition ON for 3 seconds. Turn the key OFF, then repeat the key cycle five to ten times until the pressure gauge shows at least 30 psi. Reinspect for leaks at the fittings.
  11. Remove the pressure gauge. Start the engine and check for fuel leaks.
prev.gif next.gif

Jul 26, 2010 | 1998 Ford Explorer

1 Answer

How to change a fuel pump on a 2005 Nissan


Nissan Car Altima & Sentra 1999-06 Repair Guide
Fuel Pump - Removal & Installation
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Relieve the pressure from the fuel system.
  3. Remove or disconnect the following:
    NOTE When the fuel sending unit needs to be removed, pull the tab upwards. The tab is located on the sending unit, opposite the end of the float. After the tab is pulled, the sending unit will lift straight out of the tank bracket.
    Negative battery cable Rear seat and the access cover Fuel pump electrical connector Fuel lines from the fuel pump assembly Locking ring Fuel gauge assembly Fuel tube and connector from the fuel gauge
    Fuel pump by pinching the 2 locking tabs together. Lift the fuel pump assembly straight upward and out of fuel tank. O-ring and discard
  4. Place a clean rag in the hole to keep out dirt.
To install:
  1. Remove the rag
  2. Install or connect the following:
    NOTE Verify that the mark on the fuel tank and the components are aligned when installing the pump and fuel gauge sending unit.
    New O-ring and fuel pump Electrical connection and fuel tube to the fuel gauge sending unit Fuel sending unit into the tank
  3. If equipped with a threaded lock ring torque the ring to 22-26 ft. lbs. (30-35 Nm). If equipped with a lock ring held by six retaining screws, torque the screws to 18-22 inch lbs. (2-2.5 Nm).
    Fuel lines and fuel pump electrical connector. Always install new clamps on the fuel lines. Negative battery cable
  4. Start the engine, check for leaks and repair if necessary.
    Fuel pump access cover Rear seat

The fuel pump is located in the fuel tank on all vehicles. In-tank fuel pumps are accessible by lifting up the rear seat to gain access to the inspection cover.
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Relieve the fuel system pressure.
  3. Remove or disconnect the following:
    Negative battery cable Rear seat from the vehicle Inspection cover that is located under the rear seat Inlet and outlet fuel lines from the fuel pump assembly Fuel pump and gauge wiring connections 6 mounting bolts that secure the fuel pump assembly to the top of the fuel tank
  4. Raise up the fuel pump assembly and detach the fuel tubes and connector.
    Fuel gauge assembly Fuel pump with the fuel chamber
  5. Pull up the front of the fuel pump chamber and slide the chamber forward.
    Fuel pump from the chamber O-ring seal or gasket
To install:
  1. Install or connect the following:
    Fuel pump to the fuel pump chamber and slide chamber rearward Fuel pump with the fuel pump chamber Fuel gauge assembly using a new O-ring Fuel tubes and connector. Use new hoses and clamps. 6 mounting bolts to the top of the fuel gauge unit and torque the bolts to 18-22 inch lbs. (2-2.5 Nm) Fuel pump and gauge wiring connections New inlet and outlet fuel lines to the fuel pump assembly Negative battery cable
  2. Start the vehicle, check for leaks and repair if necessary. Inspection cover and the rear seat

Hope helps (remember comment and rates this).

Jul 07, 2010 | 2005 Nissan Sentra

1 Answer

NEED TO REPLACE FUEL PUMP FOR 1996 fORD eXPLORER, V6 4.0. WHERE IS IT AND HOW DO I GET TO IT?


Great SUV, I have the same model; for Ford Ranger/Explorer/Mountaineer 1991-1999 check this procedure to Fuel Pump - REMOVAL & INSTALLATION...
(see Figures 1, 2 and 3)

To gain access to the fuel pump, it is necessary to remove the fuel tank.
  1. Depressurize the fuel system and remove the fuel tank from the vehicle.
  2. Remove any dirt that has accumulated around the fuel pump attaching flange, to prevent it from entering the tank during service.
  3. Turn the fuel pump locking ring counterclockwise using a locking ring removal tool and remove the locking ring.
  4. Remove the fuel pump and bracket assembly.
  5. Remove the seal gasket and discard it.
To install:
  1. Put a light coating of heavy grease on a new seal ring to hold it in place during assembly. Install it in fuel tank ring groove.
ab80e6f.jpg

Fig. 1: Fuel pump and sending unit used on the Regular Cab Ranger pick-up

fe10412.jpg

Fig. 2: Fuel pump and sending unit used on the Super Cab Ranger pick-up

2bf46c6.jpg

Fig. 3: Fuel pump and sending unit used on the Explorer and Mountaineer
  1. Insert the fuel pump assembly into the fuel tank, then secure it in place with the locking ring. Tighten the ring until secure.
  2. Install the tank in the vehicle.
  3. Install a minimum of 10 gallons of fuel and check for leaks.
  4. Install a pressure gauge on the throttle body valve and turn the ignition ON for 3 seconds. Turn the key OFF , then repeat the key cycle five to ten times until the pressure gauge shows at least 30 psi. Reinspect for leaks at the fittings.
  5. Remove the pressure gauge. Start the engine and check for fuel leaks.

Hope help with this; remember comment and rated this help. TY for using Fixya.

May 28, 2010 | 1996 Ford Explorer

2 Answers

How do I replace a fuel pump on a 2003 escape? Engine not getting enough fuel so when starting car, I get crank but cannot get engine to turn over. Perhaps the pump can wait if someone has other...


Check to see if the inertia switch is tripped first. Read your owner manual for location and how to reset. Just push the button. It usually only trips in an accident to shut off the fule pump in case there is a leak.

here is how to replace the pump. It's good because you don't have to drop the tank!
  1. Relieve the fuel pressure. For additional information, refer to Section 310-00 . (I disconnect inertia switch and crank engine for 10 seconds to revilve pressure).
  1. Disconnect the battery ground cable. (I don't do this myself).For additional information, refer to Section 414-01 .
  1. Lift the LH rear seat cushion.
  1. Position the carpet aside.
  1. Remove the screws and the fuel pump module access cover.
  1. Disconnect the electrical connectors.
  1. Disconnect the fuel and vapor lines from the fuel tank. For additional information, refer to Section 310-00 .
  1. s3k~us~en~file=ani_caut.gif~gen~ref.gif WARNING: The fuel tank may be pressurized. Remove the fuel tank filler cap slowly. If a hissing sound is heard, wait until the condition stops before removing the fuel tank filler cap. If these precautions are not followed, fuel may spray and cause personal injury.
    Remove the gas cap.
  1. Using the special tool, remove the fuel pump module. (If you don't have tool, use a chisel or screwdriver and tap counterclockwise to rotate the ring).
46cace5.gif
  1. NOTE: Install a new fuel pump mounting gasket.
    To install, reverse the removal procedure.
    • Start the engine and visually inspect for leaks.

Not a bad job. buy pump on ebay or new at discount at tascafordparts.com

Jun 21, 2009 | 2003 Ford Escape

1 Answer

Remove fuel pump from tank ford windstar 98


To gain access to the fuel pump, it is necessary to remove the fuel tank.
  1. Depressurize the fuel system and remove the fuel tank from the vehicle.
  2. Remove any dirt that has accumulated around the fuel pump module attaching flange, to prevent it from entering the tank during service.
  3. Turn the fuel pump module locking ring counterclockwise using a locking ring removal tool or a brass drift and remove the locking ring.
  4. Remove the fuel pump module.
  5. Remove the seal gasket and discard it.

To install:
  1. Put a light coating of grease on a new seal ring to hold it in place during assembly. Install it in fuel tank ring groove.
  2. Insert the fuel pump module into the fuel tank, then secure it in place with the locking ring. Tighten the ring until secure.
  3. Install the tank in the vehicle.
  4. Install a minimum of 10 gallons of fuel and check for leaks.
  5. Install a pressure gauge on the throttle body valve and turn the ignition ON for 3 seconds. Turn the key OFF , then repeat the key cycle five to ten times until the pressure gauge shows at least 30 psi.
  6. Check for fuel leaks at the fittings.
  7. Remove the pressure gauge.
  8. Start the engine and check for fuel leaks.

May 26, 2009 | 1998 Ford Windstar

Not finding what you are looking for?
1998 Chrysler Cirrus Logo

Related Topics:

48 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chrysler Experts

yadayada
yadayada

Level 3 Expert

79186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

chargerhp
chargerhp

Level 3 Expert

814 Answers

Are you a Chrysler Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...