Question about 2006 Nissan Frontier

3 Answers

How do I read 2006 nissan frontier engine codes ?

Posted by on


3 Answers

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 1,615 Answers

With a code reader. Some auto parts stored will do this for free but be aware that a code never really tells you exactly whats going on. To confirm a given part is bad the system has be checked first.
Also with alot of newer cars when everything is tested and deemed ok its possible there is a PCM update to address certain codes. So in these cases you wouldnt know unless a professional diagnosed the car for you.

Posted on Dec 11, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 564 Answers

You count the flashes on your check engine light if it flashes three quick times then pauses then flashes another 4times the code would be 34. make sure you let it cycle to ensure that you have read all of the codes. you have read them all when they start to repeat.

Posted on Dec 11, 2009

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Master
  • 1,214 Answers

Take it to AutoZone or Oreilly's and they will read the codes/ Take a pencil and paper to write the codes down as each are important in diagnosing the problems you may have.

Posted on Dec 11, 2009

6 Suggested Answers

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

  • 366 Answers

SOURCE: 2004 nissan frontier , code po132 , v-6 engine

bank 1 sensor 1 is usually first sensor on drivers side!

Posted on Jun 24, 2009

  • 2004 Answers

SOURCE: nissan frontier 98


for code listing for your car.

Rate this.

Posted on Aug 09, 2009

  • 484 Answers

SOURCE: 2006 Nissan frontier 4 cylinder belt diagram + tensioner pulley

They are under the hood or on the front crossmember.


Posted on Sep 14, 2009

  • 3640 Answers

SOURCE: engine repair code P0325

po325--ignition system or missfire.

Posted on Sep 16, 2009

  • 14585 Answers

SOURCE: 2000 nissan frontier knock sensor code & distributor

no but the knock sensor does send a signal the ecm and it will ****** or advance the distributor timing

Posted on Jun 14, 2010

Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

2 Answers

What are some signs that a speed sensori s bad on a 2003 frontier nissan

fault code is p0500
loss of anti-lock brakes the "anti-lock" or "brake" warning lamps on the dash may be lit the speedometer or odometer may not work properly (or at all) your vehicle's RPM limiter may be decreased the shifting of an automatic transmission may become erratic other symptoms may also be present

Read more at:

if the engine check light is on
the engine computer has fault codes to be read

this is the speed sensor on a 2003 nissan frontier



Oct 14, 2016 | 2003 Nissan Frontier Crew Cab

1 Answer

What is the location of crank angle sensor for the 2006 nissan frontier ?

On the bottom of the transmission bellhousing. Small sensor with a wiring connector, and 1 bolt attaching it to the bellhousing

Aug 10, 2014 | 2006 Nissan Frontier

1 Answer

I have a 2006 nissan frontier i took it to the dealer because the check engine light came on they said the code DTC P0463 FUEL LEVEL SENSOR CIRCUIT was the problem they charged me $600 to repair. upon...

If it was a recall and your vehicle met the requirements for that recall contact Nissan usa and get them to issue you a credit. If the vehicle falls under a campaign or bulletin, that is only covered under basic warranty

Oct 21, 2013 | 2006 Nissan Frontier

1 Answer

2006 nissan frontier xe....engine stall at high speed and back to low speed engine stalls and stop.........hard start after engine shutdown for 1hr..

Had same problem discovered air intake after MAF sensor was cracked and leaking in air .check before replacing anything else more expensive!!!!

Feb 09, 2013 | 2006 Nissan Frontier Crew

1 Answer

My Nissan Frontier 2006, light of service engine soon came on and it has not turn off ever sense, will like to know what to do?

Take your Nissan to AutoZone parts store and have them put it on there computer to read what code the light came on for..its FREE...that will head you on the right path...they should tell you what the code means, if not...let me know what the code is and i will look it up for you....Hope this helped you ??

Jun 10, 2011 | 2006 Nissan Frontier

1 Answer


U1000 - CAN Communication Line Signal Malfunction

- Harness or connectors (CAN communication line is open or shorted)
- Faulty Engine Control Module (ECM)

- Poor harness ground connection

There is a service bulletin for the following Nissan models with U1000 code:

2002-2006 Nissan Maxima
2004-2006 Nissan Titan
2004-2006 Nissan Armada
2002-2006 Nissan Sentra
2005-2006 Nissan Frontier
2002-2006 Nissan Altima
2005-2006 Nissan Xterra
2005-2006 Nissan Pathfinder
2004-2006 Nissan Quest
2003-2006 Nissan 350Z
2003-2006 Nissan Murano

The service bulletin suggest cleaning engine and body harness ground connection to repair problem.

Feb 14, 2011 | Nissan Versa Cars & Trucks

1 Answer

I have a 2006 nissan frontier and the service light came on what should i do and is it serious

It is most likely a faulty sensor. Any sensor or electrical problem will set the light off. If the car is not running weird then you should be ok. Many part stores will read your engine codes for you and tell you exactly what is wrong.

Sep 09, 2009 | 2006 Nissan Frontier

1 Answer

Gas gauge not accurate engine light on does not go over a quarter even if i full the tank

You may need a new fuel level sending unit. Check Nissan's help forum. You can get a free login and than will be able to download upto two files a day. Check their service bulletins out. They had a problem with the older Frontiers and created bulletin NTB99-064 check and see if any thing new has come about. This bulletin details fixing a ground connection under the passengerside kickpanel. Your check engine light may be something else, you might check and see if any of your local part shops do free code reads. FYI My 1998 frontier had a similar problem which I ignored until it started blowing fuel pump fuses. Turned out the fuel level sender started to short out and take the fuses.

Sep 06, 2009 | 2006 Nissan Frontier

Not finding what you are looking for?
2006 Nissan Frontier Logo

519 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts


Level 3 Expert

83096 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

gerry bissi

Level 3 Expert

4387 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides