Question about Ford Mustang

Open Question

2000 ford mustang key wont turn in the ignition steering wheel spin all the way around.

Posted by on

Ad

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad
  • 314 Answers

SOURCE: Ignition key wont turn on

My guess is that you have a 'load' of keys on the fob?? Very ******* the switch! Try a spray of penatrating oil. Not wd! Move the key in an out just a bit while turning on. You will need to replace the switch though. Frankster016

Posted on Oct 26, 2008

Ad
  • 5 Answers

SOURCE: key wont turn in ignition

had the same problem with a 99 dodge van. tow truck driver put the key into the ignition and tapped it a couple of times while turning the key to freed it up and start the engine. works as long as you leave the key in the ignition so i use a second key to lock/unlock the van. hope this works for you. gary

Posted on May 20, 2009

  • 2 Answers

SOURCE: Lock steering wheel...Key won't turn in the ignition

Make sure to push the brake firmly with you foot. I do this all the time.

Posted on May 28, 2009

  • 1 Answer

SOURCE: can't turn key in ignition lock cylinder 2000 dodge stratus

heat it up with a hair dryer

Posted on Jun 12, 2009

localwonder
  • 6784 Answers

SOURCE: Replacing the ignition switch in a 96 ford mustang cobra svt

Follow these steps carefully. this will help you achieve this replacement.



  1. Disconnect the negative battery cable from the terminal on the battery. Remove the upper and lower steering column covers by unscrewing them.

  2. Remove the steering wheel by lifting off the center cover, disconnecting the horn wire and removing the retaining nut and washer. Make a mark on the steering wheel spline and the wheel itself so you can line it back up precisely. Pull the steering wheel straight back to remove from the shaft.

  3. Take off windshield wiper and turn signal switches by pulling them off as you did the steering wheel and disconnect the wiring. Slide the spacer sleeve off of the steering column.

  4. Unscrew the ignition switch mounting screws. Pull out the ignition switch. Disconnect the wiring connector from back of the ignition switch. Simply loosen the tabs and pull it out.

  5. Insert your key into the ignition. Turn the ignition switch to the locked position. Depress the retaining pin with a small screwdriver and turn the key to the Off position to free the cylinder. Once it is free, turn the key to lock position and remove the key and key cylinder.

  6. Install your old key cylinder into the new ignition switch assembly. Make sure the contacts in the cylinder and assembly line up. Reattach wiring to ignition switch, slide it into place, screw in mounting screws and reassemble steering wheel and switches.

Posted on Jun 17, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Bad ignition switch loose wont start


Model year make and model? Lot of newer models when you turn you're steering wheel all the way to the right an anti theft activates locks the steering column if you insert you're key well you move the steering wheel to the left you're car should start also you may overall just need a ignition switch replacement.

Jun 18, 2014 | 2000 Ford F150 Flareside SuperCab

2 Answers

1998 Ford Escort steering wheel lock will not unlock. Seems jammed.


The steering wheel was turned when the key was removed. So when you try to turn on the key, turn the wheel one way and the other way to release the pressure on the key. The key should turn ok.
Hope this helps.

Apr 19, 2013 | 1998 Ford Escort

1 Answer

Key wont turn, steering wheel is stuck


I have a 2001 Ford Focus ZX3 manual transmission. The steering wheel is stuck and the key won't go all the way in and turn the ignition. I change the passenger side power mirror and this happen. What can I do?

Jun 07, 2010 | 2000 Ford Focus

1 Answer

Can't turn ignition key and steering wheel in


Play around with the steering wheel. Also jiggle the ignition key switch while doing this. It should eventually free up yiour igniton.

Feb 03, 2010 | 2000 Hyundai Accent

1 Answer

Replacing the ignition switch in a 96 ford mustang cobra svt


Follow these steps carefully. this will help you achieve this replacement.



  1. Disconnect the negative battery cable from the terminal on the battery. Remove the upper and lower steering column covers by unscrewing them.

  2. Remove the steering wheel by lifting off the center cover, disconnecting the horn wire and removing the retaining nut and washer. Make a mark on the steering wheel spline and the wheel itself so you can line it back up precisely. Pull the steering wheel straight back to remove from the shaft.

  3. Take off windshield wiper and turn signal switches by pulling them off as you did the steering wheel and disconnect the wiring. Slide the spacer sleeve off of the steering column.

  4. Unscrew the ignition switch mounting screws. Pull out the ignition switch. Disconnect the wiring connector from back of the ignition switch. Simply loosen the tabs and pull it out.

  5. Insert your key into the ignition. Turn the ignition switch to the locked position. Depress the retaining pin with a small screwdriver and turn the key to the Off position to free the cylinder. Once it is free, turn the key to lock position and remove the key and key cylinder.

  6. Install your old key cylinder into the new ignition switch assembly. Make sure the contacts in the cylinder and assembly line up. Reattach wiring to ignition switch, slide it into place, screw in mounting screws and reassemble steering wheel and switches.

Jun 17, 2009 | 1996 Ford Mustang

1 Answer

STEERING COLUMN


Yes something is wrong,and yes you can replace what is broke without replacing the whole thing.
Sounds like the rubber connector under the hood.

May 06, 2009 | 2000 Ford Mustang

1 Answer

Steering wheel locked and ignition wont turn


Yes it does sound to me like the key is the problem.
the only other thing for a steering locking up would be the steering lock silenoid but that is activated by the brake pedal and the key has to be turned
if this is the orginal key it could be something else because the key and the tumblers inside the ingintion would wear down the same time together,but is the is a replacement key or back-up it will be the key because the tumblers would have been worn done by a different key.
try wiggling the key as you turn maybe you can get it to turn.
You will likely have to replace the ignition and key together.

Feb 28, 2009 | 2000 Ford Focus

1 Answer

I changed my transmission fluid on my 1999 mustang tried to start key wont even turn


Changing the fluid would not cause this issue your describing. try turning the steering wheel hard to the left or right to unlock the ignition.

Nov 03, 2008 | 2003 Ford Mustang

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

197 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

83036 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

gerry bissi

Level 3 Expert

4387 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...