Question about 1991 Toyota Pickup

1 Answer

Can I repair the fan clutch pulley in a 1991 toyota pickup myself without going to a mechanic

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,498 Answers

Hey there Grizzly spit,

I don't know what's wrong with it so I can't answer that one, But you sure can replace it without a mechanic.

Mike

Posted on Dec 11, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Can i replace the water pump in a 1997 Nissan pickup without messing with (replacing) the timing chain?


D21 Pick up? The water pump is not timing belt driven. It is drive belt drive with a pulley held on with 4 bolts.

So, yes, the water pump can be replaced without touching the timing components. :-)

Nov 22, 2011 | 1997 Nissan Pickup

1 Answer

How long does it take to replace a clutch on a 1991 toyota pickup 4 wheel drive 6 cylinder 3.0 liter engine? The clutch burnt out and I'd like to know how many hours labor it would be to replace it...


hello, it takes about 5 hours actual time for a mechanic using air powered tools and has all the equipment needed such as a transmission jack, a lift and the tools needed.
\Keep in mind that this time varies depending on the skill and experience of the mechanic, the shop can charge you whatever they feel is fair and still make a profit, most shops charge a 'flat rate' this means they have a set price for each repair procedure, this also varies with location. a shop on the east or west coast will tend to be more expensive than in the Midwest.

Aug 24, 2017 | 1991 Toyota Pickup

1 Answer

Waterpump 1994 toyota 4 cyclinder


you need a pully puller tool

Feb 28, 2010 | 1994 Toyota Pickup

2 Answers

91 toyota pickup with clutch problems


First you have to bleed air from clutch fluid.
if it is not ok, Remove clutch agan & check pressure plate finger blance or damage.

Nov 18, 2009 | 1991 Toyota Pickup

1 Answer

Where is the shift linage located on an 1985 toyota 4x4 pickup truck? I still cant shift into gear from thje last support you gave me


Without seeing the problem myself, it sounds like you have a clutch problem. It could be the linkage but sounds like the clutch. A manual transmission's linkage is located on the top. It can be reached from the inside of the vehicle through the floorboard. The linkage is attached to the lower end of the gear shift and enters the top side of the transmission. A vehicle repair manual may be helpful, Haynes and Chilton are good ones. Good luck

Oct 16, 2009 | 1985 Toyota Pickup

1 Answer

Fan clutch removal


the four bolts holding the fan clutch to the water pump pulley are loosened counter clockwise. If you don't have a pulley holding tool at hand, use a wrench(closed end side) as a locking leverage on the studs(do not place the wrench on the nuts) while loosening the nuts 1 by 1 with another wrench. When reinstalling use the same method, but place black elec tape over the studs(prevent thread damage) after you hand tighten the bolts for the fan clutch. hopefully this helps

Jul 20, 2009 | 1994 Toyota Pickup

3 Answers

1991 Toyota pickup 4WD clutch slipping


There is an adjustment for the clutch pedal under the dash where the push rod goes thru the firewall. There is only aprx. 1/2" of adjustment so be careful when making an adjustment, if your clutch is slipping then you need to shorten the throw of the push rod.

May 06, 2009 | 1991 Toyota Pickup

1 Answer

Loose Pulley


it could need repacing or tack welding its ether power sterring or altanator pully.

Dec 05, 2008 | 1991 Toyota Pickup

1 Answer

A/c belt replacement


It should go right on without any hassle. Double check your belt. Buy another one at a different place, you can always return one of them. It sounds like the wrong size.

Aug 08, 2008 | 1991 Toyota Pickup

Not finding what you are looking for?
1991 Toyota Pickup Logo

Related Topics:

140 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

Marvin
Marvin

Level 3 Expert

81285 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...