Question about 2000 Dodge Ram 1500 Truck

Open Question

How to install reese 14K part no 30031 slide fifth wheel universal installation kit.I think it is 30035

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My jayco fifth wheel trailer slide out does not come out evenly!


Use wheel bearing grease to lube the slides. There is a You Tube video that shows you how to maintain the slide out too.

Oct 01, 2014 | Cars & Trucks

1 Answer

Tranny over heats when im pulling my trailer


You can actually buy a trans cooler kit from most motor shops. Install one is quite easy and most kits come with instructions. Get a larger one if your car is going to be doing some harder work.. You will also get a longer life from your trans

Jan 26, 2014 | Cars & Trucks

1 Answer

Wiring Diagram for hayman reese brake controller


Hello! Go to this link for PDF installation guide with wiring...

http://www.caravansplus.com.au/pdf/hr-5300.pdf

Guru...Saailer

I’m happy to help further over the phone at https://www.6ya.com/expert/david_6df67de3b14de867

Oct 25, 2011 | Cars & Trucks

1 Answer

How far back from the cab on a 2009 silverado short bed do i install hitch?


  • Hope this helps and thank you for using FixYa.
Regards, Tony

Jul 15, 2011 | Chevrolet 2500 Cars & Trucks

1 Answer

Will I need a caliper reset tool kit to change the brakes on my 2007 toyota sienna or will a standard c-clamp do the job? And since it is an ABS system, I assume that brakes must be bled, correct?


Brake Pads Removal & Installation Front To Remove:
  1. Remove the front wheels. Front brake caliper (exploded view) toyota-09-00-5838.gif

  2. Loosen the caliper bleeder.
  3. Hold the slide pin; remove the 2 mounting bolts and remove the brake caliper from the support.
  4. Support the caliper.
  5. Open the brake bleeder. Press the caliper piston into the bore.
  6. Close the bleeder after the piston has reached the bottom of the caliper bore.
  7. Remove the brake pads, support plates, wear indicators and anti squeal shims.
  8. Remove the slide pins and bushings from the caliper support.
To Install:
  1. Lubricate the slide pins and bushings with brake grease.
  2. Install the bushing on the slide pin.
  3. Install the slide pin on the caliper support.
  4. Install the brake pad support plates on the caliper supports.
  5. Lubricate the anti squeal shims with brake grease.
  6. Install the anti squeal shims on the brake pads.
  7. Install the pad wear indicator facing upward and install the pads on the caliper support.
  8. Install the caliper on the support.
  9. Install the 2 mounting bolts, hold the slide pins and tighten 25 ft-lb (34 Nm).
  10. Fill the reservoir and bleed the brakes.
  11. Install the front wheels.
Rear To Remove:
  1. Remove the rear wheels.
  2. Loosen the caliper bleeder. Rear brake caliper (exploded view) toyota-09-00-5842.gif

  3. Hold the slide pin; remove the 2 mounting bolts and rear brake caliper assembly from the support.
  4. Support the caliper.
  5. Open the brake bleeder. Press the caliper piston into the bore.
  6. Close the bleeder after the piston has reached the bottom of the caliper bore.
  7. Remove the brake pads, support plates, and anti squeal shims.
  8. Remove the slide pins from the caliper support.
To Install:
  1. Lubricate the slide pins with brake grease.
  2. Install the slide pin on the caliper support.
  3. Install the brake pad support plates on the caliper supports.
  4. Lubricate the anti squeal shims with brake grease.
  5. Install the anti squeal shims on the brake pads.
  6. Install the rear pads on the caliper support.
  7. Install the rear caliper on the support.
  8. Install the 2 mounting bolts, hold the slide pins and tighten 25 ft-lb (34 Nm).
  9. Fill the reservoir and bleed the brakes.
  10. Install the front wheels.
prev.gif next.gif

Sep 18, 2010 | 2007 Toyota Sienna

1 Answer

Rear wheel bearing


Well, you picked a beauty to fix. I don't think that either a 2 or 4 wheel drive will make a difference. The biggest problem is that after you remove the axle from the car you need a special bearing removal tool, and a slide hammer to remove the bearing from the axle. Then you need a special bearing installation tool and a universal driver handle to install the new axle shaft bearing. And last, you need a axle pinion oil seal installation tool to install the oil seal. If you are not a skilled mechanic, I would suggest that you find a local reputable mechanic and let him do this repair for you.

Oct 07, 2009 | 2003 Oldsmobile Bravada

1 Answer

As i turn a knockn sound from the wheel whale comes throw the car and throw the wheel


GM and Cadillac had issues with the steering columns and they offer a kit that is more of a temporary bandaid than anything. The noise is caused by excessive clearance in the 2 shafts where they meet up on the slide yoke, the kit that they offer has a different grease to install in the slide yoke but like I said it is very temporary and to this day GM has not offered a solution to this problem that is permanent.

Apr 07, 2009 | 2000 Cadillac Escalade

1 Answer

Trailer kit installation


It should have. If not a reputable hitch like Reese or Hidden Hitch will come with nut plates. Hope this helps.

Feb 05, 2009 | 2006 Toyota Sienna

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

479 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

83096 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...