Question about 2004 Hyundai Elantra

1 Answer

Trying to find out how exactly to adjust the height at which my headlights shine. They are currently pointed too high?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Hyundai Master
  • 22,382 Answers

How did they get high ,has it switch to lower them ?? on the dash by the light switch is normally a control to raise or lower them

Posted on Dec 11, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Can the headlights be adjusted in 2013 Camry


Yes they should be adjustable because people change tyre profiles front to rear and this alters the drive angle.The adjustment screws are in the headlamp housing behind lamps accessed from the hood/ bonnet side.you do need to do this properly so they align together at the legal height for full beam.there is plenty of online information on the correct height for full beam...once you have made sure all Your tyres are at the right pressure....park on level ground ...at least 3 meters from front of a wall ....and at right angles to the wall....measure the height to the centre of headlight to ground .......mark the right light horizontal line for correct height on the wall and make sure you put lights on full beam....they should shine slightly below (say an inch )to the marked the measurement of height of lamp on the vehicle....adjust until the right hand light horizon is an inch below...now mark vertical line to cross centre of reflected light....this will give you a register point to mark where the left light should fall ...this will be exact distance apart as on vehicle and again adjust left until it falls below 1inch of the measured height line of lamp on car......mark distance from right to left light and mark the same height in chalk....then adjust left light to pinpoint marked chalk cross.adjust the beams by turning the spring loaded screws behind the lights.once you are happy check dipped positions....on right hand drive the lights should dip below and left.left hand drive dip below and right.you probably didn't need so much info but ...hey it's free and it saves any misunderstanding.hope this is of help...please vote.thankyou.

Feb 07, 2015 | Cars & Trucks

1 Answer

Headlights point to high


There are adjusting knobs beside the head lights housing 3 normally and by adjusting each at a time the head light can be aimed down left and right.. Correct adjustment will be when the center of the beam is at the same height as the center of the head light at a distance of 3 ft in from of the car on level ground. Check that the rear of the car is at correct ride height as sagged suspension will cause this problem. Consider if you have a caravan hooked up then the headlights will point up. . Same problem.

Apr 04, 2013 | 2009 Lexus GS 350

1 Answer

How do I adjust the headlight beams on my 1991 Dodge Spirit?


I believe these have adjustment screws between the headlight bulb and the headlight bezzle on the top and bottom center of the headlight.

Crouch down so the bulb would be shining right in your eyes if it were on. You should see the adjustment screws I'm talking about in there.

You should be able to shine the lights on a garage door or wall and move the screws in or out to get the desired beam height you're looking for.

Mar 30, 2010 | 1991 Dodge Spirit

1 Answer

Adjusting Headlight on Mazda 626


At the back of the headlight there are screws that adjust up and down and left to right,look carefully as it will be written on the headlight,you will see it stamped into the top of the housing just follow the indicators on the light to adjust it down,and park in front of a wall on a flat surface if possible at night or dusk to see how much youve changed the height,its not difficult to do just look carefully

Nov 18, 2009 | 1995 Mazda 626

5 Answers

How do i adjust my headlingt on a 2001 suzuki xl7


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Nov 14, 2009 | 2001 Suzuki Xl 7

2 Answers

Adjust (aim) headlights on a 1990 Ford Taurus


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Oct 13, 2009 | 1990 Ford Taurus

1 Answer

HOW DO I ADJUST THE LOW BEAM HEADLIGHTS TO SHINE


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Oct 06, 2009 | 2001 Hyundai Tiburon

2 Answers

Can't adjust the height of the headlights


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Sep 13, 2009 | 2004 Audi TT

1 Answer

I replaced the headlight assemblies with eagle eye headlights How do I adjust the headlights. One shines up in the trees as if I was con hunting


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Mar 14, 2009 | 2001 Kia Sportage

1 Answer

Headlight adjustment for 2006 Infiniti M35


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Feb 04, 2009 | 2006 Infiniti M35

Not finding what you are looking for?
2004 Hyundai Elantra Logo

79 people viewed this question

Ask a Question

Usually answered in minutes!

Top Hyundai Experts

Marvin
Marvin

Level 3 Expert

83036 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Hyundai Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...