Question about 2005 Mercury Monterey

1 Answer

After replacing the battery, the doors and liftgate will not open with the remote.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 10 Answers

This sounds like you need to reset the fuse for these features. this is similar to oil changes on newer cars, after the change is done, a fuse needs to be pulled and put back in to reset the system of the oil light. I'm only shooting a guess here, but if all that was done was a battery replacement, the system was 'reset' when the battery was removed. Check the fuses.

Posted on Feb 27, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2005 GMC Yukon that the rear hatch does not lock. Wouldn't be a problem but no manual key hole to lock it. Must be some kind of lock sensor. Is on the driver door panel or by the hatch?


The rear hatch locking is computer contolled .
The BCM also runs diagnostics on the liftgate lock relay control circuit and will set DTC B3825 as current and also send a Class 2 message to the DIC. The DIC will display REPLACE LIFTGATE FUSE to inform the driver that a fault has been detected in the liftgate lock circuit and that the liftgate is not locked. Faults that will set the DTC and cause the DIC to display the message could be any of the following:
• An open ECC fuse
• An open or short to ground in the liftgate lock relay battery positive voltage circuit
• A faulty liftgate lock relay
• An open or short to ground in the liftgate lock relay control circuit
• A short to ground in the liftgate lock actuator lock control circuit
• A faulty BCM

The liftgate lock relay supply and coil sides receive a constant voltage through the battery voltage supply circuit and the ECC fuse. The normally closed contact is connected to ground and the control side is connected to the body control module (BCM). A lock function will occur when a door lock switch activation, keyless entry lock transmission, auto door lock function or a liftgate lock function has been received by the BCM. The BCM will then ground the control side of the liftgate lock relay. This energizes the relay and allows voltage to be applied to the liftgate lock actuator lock control circuit. Since the other side of the liftgate lock actuator is connected to the normally closed contacts of the door unlock relay to ground, the liftgate will lock. When an unlock function occurs the BCM will ground the control side of the unlock relay and the rear doors and liftgate will unlock.
The power door lock system consists of the following components:
• The driver door module (DDM)
• The passenger door module (PDM)
• The body control module (BCM)
• The driver information center (DIC)
• The rear door lock switch
• The door lock relay
• The door unlock relay
• The liftgate lock relay--utility vehicles with liftgate only
• The reversible door lock actuators in each of the doors and liftgate
• LOCKS 20A fuse (rear lock/unlock relay supply voltage)
• ECC 10A fuse (liftgate lock relay supply voltage)

If i were to guess i would say you mite need a new lock actuator , but i don't guess . You could take the hatch inside panel off an check for B+ voltage for the lock actuation as someone pushes the switch . Or have it checked for codes .

Dec 21, 2016 | GMC Cars & Trucks

1 Answer

Power lift gate will not operate


You have to pull the inside door panel off an check it out , only way !
  • The lift gate latch release is inoperative/does not operate correctly
  • Circuitry
  • Liftgate release switch (integral to the liftgate release handle)
  • Liftgate release motor (integral to the liftgate latch)
  • Power liftgate module
  • SJB
  • Go To Pinpoint Test F .
Normal Operation The smart junction box (SJB) does not release the liftgate unless the doors have been unlocked electronically or the request is initiated from a remote keyless entry (RKE) transmitter.
The SJB sends a voltage signal to the liftgate release switch (part of the liftgate release handle) through circuit CPL45 (BN). When the switch is activated (the handle is pulled), the signal is routed to ground through circuit GD150 (BK/WH). When the SJB detects a request from the liftgate release switch, the SJB provides voltage through circuit CPL10 (BN/BU) to the liftgate latch release motor (integral to the liftgate latch) (vehicles with a manual liftgate) or the power liftgate module (vehicles equipped with a power liftgate). For vehicles with a manual liftgate, ground for the liftgate latch is provided through circuit GD150 (BK/WH).
DTC B2666 - is an on-demand DTC that sets when the SJB detects a short to ground from the liftgate release switch input circuit.
DTC B273A - is an on-demand DTC that sets when the SJB detects a short to ground from the liftgate latch release output circuit.
DTC B273B - is an on-demand DTC that sets when the SJB detects an open or short to voltage from the liftgate latch release output circuit.
    Possible Causes
  • Circuit CPL45 (BN) open or short to ground
  • Circuit CPL10 (GN/WH) open, short to ground or voltage
  • Circuit GD150 (BK/WH) open
  • Liftgate release switch (integral to the liftgate release handle)
  • Liftgate release motor (integral to the liftgate latch)
  • Power liftgate module
  • SJB
Your best bet is to take it to the dealer !

Nov 04, 2015 | 2008 Ford Expedition Eddie

1 Answer

Power liftgate will not open with remote, instrument panel control or button in rear cargo on lincoln mkx


It can be faulty switch or its issue with lift gate latch.Its got stuck up hard or cracked inside.It has to be inspected.-----------
There are few help links with proper solutions for these problem.I suggest you to refer the links.
Click the link below:----
2007 Mercury Mountaineer: Liftgate will not Unlock or Open? http://whoisbyme.blogspot.in/2012/06/2007-mercury-mountaineer-liftgate-will.html
------------
Adjust Hydraulic Lifters? http://schematicsdiagram.blogspot.in/2012/04/adjust-hydraulic-lifters.html
-----------
How to open rear lift gate? http://repairhelpcenter.blogspot.com/2011/12/how-to-open-rear-lift-gate.html

--------- Power Liftgate Shuts Down http://whoisbyme.blogspot.in/2012/07/power-liftgate-shuts-down.html
------------ Power Lift Gate Will Not Remain Open http://whoisbyme.blogspot.in/2012/07/power-lift-gate-will-not-remain-open.html
----------- Power Lift-gate will not Operate http://whoisbyme.blogspot.in/2012/07/power-lift-gate-will-not-operate.html
------------- Liftgate will Not Stay Up Open? http://whoisbyme.blogspot.in/2012/07/liftgate-will-not-stay-up-open.html

---------------- Rear Door will not open http://whoisbyme.blogspot.in/2012/07/rear-door-will-not-open.html
------------ 2000 Toyota Corolla: Rear Door wont open from outside or inside? http://whatisbyme.blogspot.in/2012/05/2000-toyota-corolla-rear-door-wont-open.html

--------------

These details will help.
Thanks.

Nov 25, 2012 | 2007 Lincoln MKX AWD

1 Answer

2004 lincoln navigator ,doors will not open rear hatch will not unlock


The door locks are controlled by the vehicle security module (VSM). It gets power from fuses 30, 5, 6, and 40 in the central junction box (CJB). You say you checked these and all are OK. Therefore the problem must be in the door lock actuators, the door lock relays, or the door lock switches. I doubt that all of these are defective, so the VSM may be defective.

The liftgate is controlled by the power liftgate module (PLM), althogh the motor in the liftgate glass actuator is controlled by the VSM. The PLM gets power from fuses 105 and 5 in the CJB. If the PLM is assumed to be OK, the source of the problem could be the liftgate unlatch motor, the liftgate cinching motor, the L/R liftgate obstacle detection strips, the liftgate home position switch, the liftgate fork bolt/detent switch. or the power liftgate open/close switch

Sep 28, 2012 | 2004 Lincoln Navigator 4x4

1 Answer

I just bought an equinox 2005 LS and I dont know how to lock the rear door.


To unlock the liftgate, press the unlock button on the Remote Keyless Entry (RKE) transmitter twice or use the power door lock switch.
To lock the liftgate, press the lock button on the RKE transmitter or use the power door lock switch. The liftgate does not have a key lock cylinder.
To open the liftgate, pull up on the handle located in the center of the liftgate.
When closing the liftgate, use the molded handles to pull the liftgate down. Push the liftgate closed until it latches.

Jul 08, 2011 | 2005 Chevrolet Equinox

1 Answer

Passenger door and liftgate do not open with remote control or door panel control both start at the same time nissan murano 2005 s model


Liftgate is connected to front RH's door actuator thru back door's "opener switch". Replacing the passenger's door lock actuator will solve the problem.

Jul 25, 2010 | 2007 Nissan Murano SE

2 Answers

Rear tail gate will not open


how to i open a stuck lift garte on a ford winstar 2000 lock broken too

Jun 14, 2009 | 2001 Ford Escape

1 Answer

2006 Tahoe Z71 Lift Gate Will Not Unlock With Remote


Take the liftgate inside panel off an check the wiring , connections etc....
rear door hatch lock repair GMC Chevrolet
chevy tahoe lift gate not opening
The liftgate will lock any time the vehicle is shifted out of park on vehicles equipped with an automatic transmission and at vehicle speeds exceeding 5 kph with manual transmission. This happens in conjunction with auto door locks if enabled or independently of auto door locks if the feature is disabled. This ensures that the liftgate is locked anytime the vehicle is shifted out of park or when the vehicle is in motion.
The liftgate lock relay supply and coil sides receive a constant voltage through the battery voltage supply circuit and the ECC fuse. The normally closed contact is connected to ground and the control side is connected to the body control module (BCM). A lock function will occur when a door lock switch activation, keyless entry lock transmission, auto door lock function or a liftgate lock function has been received by the BCM. The BCM will then ground the control side of the liftgate lock relay. This energizes the relay and allows voltage to be applied to the liftgate lock actuator lock control circuit. Since the other side of the liftgate lock actuator is connected to the normally closed contacts of the door unlock relay to ground, the liftgate will lock. When an unlock function occurs the BCM will ground the control side of the unlock relay and the rear doors and liftgate will unlock.
The BCM also runs diagnostics on the liftgate lock relay control circuit and will set DTC B3825 as current and also send a Class 2 message to the DIC. The DIC will display REPLACE LIFTGATE FUSE to inform the driver that a fault has been detected in the liftgate lock circuit and that the liftgate is not locked. Faults that will set the DTC and cause the DIC to display the message could be any of the following

Power Door Locks Inoperative - Endgate/Liftgate

Schematic Reference: Door Lock/Indicator Schematics
Connector End View Reference: Power Door Systems Connector End Views
1
Did you perform the Diagnostic System Check - Vehicle?
YES - Go to Step 2
NO - Go to Diagnostic System Check - Vehicle in Vehicle DTC Information
2
Activate the door lock switches to the lock and unlock positions.
Do both rear passenger doors lock and unlock?
YES - Go to Step 3
NO - Go to Power Door Locks Inoperative
3
Did the liftgate lock actuator lock and unlock?
YES - Go to Testing for Intermittent Conditions and Poor Connections in Wiring Systems
NO - Go to Step 4
4
Disconnect liftgate door lock actuator.
With a test lamp connected to a good ground, probe the door lock actuator lock circuit at the door lock actuator harness connector.
Activate a door lock switch to lock position.
Does the test lamp illuminate?
YES - Go to Step 5
NO - Go to Step 7
5
With a test lamp connected to a good ground, probe the door lock actuator unlock circuit at the door lock actuator harness connector.
Activate a door lock switch to unlock position.
Does the test lamp illuminate?
YES - Go to Step 6
NO - Go to Step 8
6
Inspect for poor connections at the harness connector of the door lock actuator. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs in Wiring Systems.
Did you find and correct the condition?
YES - Go to Step 10
NO .. Go to Step 9
7
Repair the open door lock actuator lock circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
YES - Go to Step 10
--
8
Repair the open in the door lock actuator unlock circuit. Refer to Circuit Testing and Wiring Repairs in Wiring Systems.
Did you find and correct the condition?
Go to Step 10
--
9
Replace the liftgate door lock actuator. Refer to Door Lock Actuator Replacement in Body Rear End.
Did you complete the repair?
Go to Step 10
--
10
Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Step 2

Apr 27, 2017 | 2006 Chevrolet Tahoe

1 Answer

2001 Ford Escape Rear Hatch won't unlock


The liftgate consists of the following components:
  • liftgate door lock actuator
  • liftgate lock cylinder (if equipped)
  • liftgate window glass
  • liftgate window latch/ajar switch
  • liftgate window glass release handle
  • liftgate latch remote control which consists of the following component:
    • liftgate release handle
  • liftgate latch, which consist of the following component:
    • liftgate latch door ajar switch
Liftgate Latch Actuator Removal and Installation
  1. Remove the liftgate latch remote control. For additional information, refer to Liftgate Latch Remote Control in this section.
SECTION 501-14: Handles, Locks, Latches and Entry Systems 2001 Escape Workshop Manual
REMOVAL AND INSTALLATION Liftgate Latch Removal and Installation
  1. Remove the liftgate trim panel.
  1. Disconnect the liftgate ajar switch electrical connector.
  1. Disconnect the liftgate latch actuating rod.
    1. Open the clip.
    1. Disconnect the actuating rod.
  1. Remove and discard the liftgate latch bolts.
  1. Remove the liftgate latch.
  1. NOTE: Make sure the liftgate latch release rod is not preloading the latch. It should be clipped in a relaxed state with no slack.
    NOTE: Position the liftgate latch release rod by pushing outboard to remove the slack.
  1. Remove the screws and the liftgate latch actuator
90f640f.gif

May 29, 2009 | 2001 Ford Escape

1 Answer

Remote Entry System not working, 05 Chrysler T&C


there is an update foe the body control module that will generally fix the problem. you will ned to take it to the dealer to have it done.

Dec 31, 2008 | 2005 Chrysler Town & Country

Not finding what you are looking for?
2005 Mercury Monterey Logo

372 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercury Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

fordexpert

Level 3 Expert

5687 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Are you a Mercury Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...