Question about 1997 Jeep Grand Cherokee

1 Answer

How kan itel witch speed senser malfunction without scaner Jeep 1997

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.


    An expert whose answer got voted for 500 times.

  • Jeep Master
  • 2,050 Answers

Unplug the harness to the sensor, and Ohm it out with a volt/ohm meter.

Posted on Dec 11, 2009


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

I have a 1997 jeep cherokee sport the tranny went bad i have a donor 2000 cherokee sport all is the same but the 2000 has 2 speed sensors the 97 has 1 in the rear if i plug in the front sensor witch is the...

wrong tranny.
the TCM shifts based in this , so
take both tranny to any tranny shop
and say make best out of 2, many can.
you could look in both FSM and see what parts need change out.
the day of simple swaps are over...
electronic shifter trans are complex. and today even more so.
with ESP, and ETC. far worse........

you should have (sorry) joined Top Jeep forum.
then asked what works. before the leap,,, not much.

Nov 20, 2013 | 1997 Jeep Grand Cherokee

1 Answer

Code 0161

if the computer is the correct part number its either the o2 senser or the heater wire is broken where it comes out of the computer test the wire first by checking the risestance from the computer to the o2 senser

Nov 19, 2013 | 2003 Jeep Grand Cherokee Limited

1 Answer

1997 cherokee on dash says fuel senser valve.goes on and off when it wants to.replaced valve on engine still does it.whats up?

Have some one check your crank angle sensor or replace it. This has caused a lot of intermittent problems on this year jeep vehicle. It will lead to the a lose of ECU function

Jul 01, 2011 | 1997 Jeep Grand Cherokee

1 Answer

How to find out witch power stering pump I have in my jeep 4.0 litre jeep

Okay, your truck steering pump may have the speed proportional steering SPS or not, the way to tell is by looking at the pump and see if you have the sensor on the pump where the high preasure line goes, heres two pictures for you to look at and compare to yours, if yours has the switch then its got the SPS type pump, if yours has no sensor then its the pump without, hope this helps good luck.9fc49e7.jpgfd856f6.jpg

Oct 09, 2010 | 1997 Jeep Grand Cherokee

1 Answer

1997 Grand Jeep Cherokee Limited 5.2 V8: Probleem: De computer doet het niet, geeft zwart beeld. Kan je de computer aan en uit zetten? Is er een zekering kapot? Alvast bedankt.

Turn the key on three times with out hitting the starter and leave it on the last time the dash display will tel you the codes and you canget an idea of what's wrong. sorry I only read and write English ( american) so I can only guess this is that you want. Good luck!

Sep 16, 2010 | 1997 Jeep Grand Cherokee

1 Answer

What energizes the cooling fan relay on a 2000 Jeep Cherokee Sport?

It is engergised by the computer witch gets its signal from the coolent temp senser What is the problom you are haveing?

Jul 13, 2010 | 2000 Jeep Grand Cherokee

2 Answers

My abs light stays on

The most common cause is low brake fluild level or the senser that checks it ib the resavoir. The scanner can check for cdes that indicate a wheel speed senser wire broke but just inspecting the wires beteen the wheels and the truck almost always finds the broken wire without the scranner. fit the wire and change the senser as needed and the system will reset itself as it checks itself each time you turn the key on and move the car. Most common problems can be found by just looking a all the parts for broken or disconnected wires

Oct 20, 2009 | 1997 Chevrolet S-10 Pickup

1 Answer

Directional signals and flashers stopped working

Hi, this is a flasher issue. its malfunctioning. its located near the Seating area, driver side, on the upper steering column housing at the top of the steering column, behind the multi-function switch.

If you would like to check the fuse. it is number 3(20a) yellow.

May 22, 2009 | 1997 Jeep Wrangler

Not finding what you are looking for?
1997 Jeep Grand Cherokee Logo

Related Topics:

34 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

83810 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22413 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides