Question about 1996 Ford Crown Victoria

1 Answer

1996 crown vic, no spark. eec? - 1996 Ford Crown Victoria

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 67 Answers

Spark control mag gon

Posted on Dec 11, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why won't 89 cRown Vic stay running unless key held forward


Usually the problem is inside the lock switch. You should have power at the EEC relay and the coil with the switch in the on position.

Jun 14, 2015 | 1989 Ford Crown Victoria

1 Answer

Will 93 crown vic ,motor work in 96 crown vic


No,not without a lot of switching of electronics

1993 is OBD1 & 1996 on is OBD2 System

The engine may be okey-- but not the induction
system or any electrical

Dec 25, 2012 | 1996 Ford Crown Victoria

2 Answers

I have a 1996 crown vic i need to know these touble codes po305 po304


P0304 means that cylinder 4 has a misfire and P0305 is a cylinder 5 misfire. What this means is you may have bad spark plugs, or bad plug wires, or you may need to replace your distributor cap and rotor. I would start with plugs and wires.

Oct 21, 2010 | 1996 Ford Crown Victoria

1 Answer

1992 ford crown vic working fine, next day no power to fuel pump or cut off switch


  1. Hi Domino, The fuel shut off is powered by the fuel pump relay (which is in the engine compartment fuse block) the fuel pump relay is powered by the EEC power relay(PCM relay) you will have to check for distribution and voltage. I hope this helps!

Aug 31, 2010 | 1992 Ford Crown Victoria

1 Answer

My 1996 crown vic will not start motos turns over and trys to start but wont I have replaced intake manifold spark pulgs. motor has spark


basics,,,air,,fuel,,spark,,compression,,timing,,,pull a few plugs,,smell them for fuel,,if dry,,,take snorkel off throttle body,, open throttle body or flap half way,,spay a little starting fluid or injector spay into throttle put the snorkel back on see if motor fires up,,if so then ck fuel delivery & pressure,,,,hope it helped

May 28, 2010 | 1996 Ford Crown Victoria

1 Answer

ODOMATOR IS NOT WORKUNG 1996 FORD CROWN VIC


The speed sensor in the transmission is most likely the problem.

Nov 26, 2009 | 1996 Ford Crown Victoria

1 Answer

1996 Crown Vic, Valve noise under heavy acceleration


No use what's in there, but have the engine de-carboned by a Ford dealer, or remove the octane adjust shorting bar located near the ignition module (retards timing 2 degrees), this will in most cases cure the issue unless there is allot of carbon in the cylinders. There are also methods of ing this de-carbon procedure at home, check on the internet for tips.

PLEASE RATE THIS SOLUTION

Oct 22, 2008 | 1996 Ford Crown Victoria

2 Answers

P0304=misfire in cylinder 4. coil? spark plug? spark plug wiring. 1999 crown vic 4.6 V8. runs ok, just little cutting out every now and then.


not coil coil it wouldnt fire at all it is either a plug or a wire replace the wire and plugs and that will fix it

Oct 06, 2008 | 1996 Ford Crown Victoria

Not finding what you are looking for?
1996 Ford Crown Victoria Logo

Related Topics:

189 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

Marvin
Marvin

Level 3 Expert

81294 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

gerry bissi

Level 3 Expert

4376 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...