Question about 1995 Jaguar XJ6

1 Answer

Where is the starter located. son ripped out wire harness, repaired it, now im in re install mode

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Jaguar Master
  • 22,326 Answers

Its on the bell housing .have a jag for spares in the yard ,trouble is you can buy a jag like this for less than 500pounds so its not worth repairing .Buy another one use it then when its annual test is due ,junk it and go to auctions and buy another

Posted on Dec 10, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 kia spectra color code ignition switch diagram pdf


PART COLOR LOCATION 12 VOLT CONSTANT WHITE/BLACK (+) and WHITE (+) IGNITION SWITCH HARNESS STARTER RED (+) IGNITION SWITCH HARNESS STARTER 2 N/A IGNITION 1 YELLOW (+) IGNITION SWITCH HARNESS IGNITION 2 N/A IGNITION SWITCH HARNESS IGNITION 3 N/A ACCESSORY/HEATER BLOWER 1 BLUE (+) IGNITION SWITCH HARNESS ACCESSORY/HEATER BLOWER 2 GREEN (+) IGNITION SWITCH HARNESS

Dec 27, 2011 | 2002 Kia Spectra

3 Answers

REMOVED ALARM -STARTER WON'T ENGAGE-NO POWER TO ENGINE


When you removed the alarm unit you cut the line to the Starter kill switch that was installed. Remove the starter kill switch which is most likely located under the dash spliced into the ignition wiring harness.

Jul 08, 2011 | 1999 Dodge Intrepid

2 Answers

Hello my car starts in runs fine but when im on the hwy driving the starter ignites like its trying to start while im driving the the car dealership ont know what the problem is ive changed...


The CRANK RELAY primary wire (control circuit) is a YELLOW / BLACK wire and it goes to pin #23 in connector C1 at the PCM. If I were a betting man, I would say that the most likely cause of this problem is that the YELLOW/BLACK wire is shorting to ground. This will cause the start relay in the UNDERHOOD FUSE AND RELAY BOX to energize and make the starter engage. This wire runs from the PCM (Located inside the air cleaner assembly) to the START RELAY. (Located on the right stut tower in the UNDERHOOD FUSE AND RELAY BOX. Inspect the wiring harness all the way along this path. You will most likely find a place where the harness is rubbed through and there you will find the YELLOW/BLACK wire is most likely shorting to ground.

Apr 01, 2011 | 2005 Pontiac Grand Prix

3 Answers

Son's 2001 jeep grand cherokee V8, he just bought it with 110000 miles, and now it clicks but won't start. It has battery power, all lights work and did start once. I assume we need a new starter and...


Just because the lights work does not ensure that the battery is good. To be sure that the battery is good it should be load tested. Most auto parts stores will do this for free, it could save you the trouble and expense of replacing the starter.

Also thouroughly inspect the cables/connectors, make sure they aren't corroded or damage.

This is the starter replacement procedure.

  1. Remove or disconnect the following:
    • Negative battery cable
    • Starter mounting bolts
    • Starter solenoid harness connections
    • Starter
    To install:
  2. Connect the starter solenoid wiring connectors.
  3. Install the starter and tighten the bolts to the following specifications:
    • 2.5L engine: 33 ft. lbs. (45 Nm)
    • 4.0L engine: Upper bolt to 40 ft. lbs. (54 Nm) and lower bolt to 30 ft. lbs. (41 Nm)
    • 4.7L engine: 40 ft. lbs. (54 Nm)
    • 5.2L and 5.9L engines: 50 ft. lbs. (68 Nm)
  4. Install the negative battery cable and check for proper operation.

Mar 24, 2011 | Jeep Grand Cherokee Cars & Trucks

1 Answer

Where is the starter located on my 2003 nissan sentra ser


Starter Motor -located to articulate with flywheel that has gear teeth between the engine and transmission accessible from down below. REMOVAL & INSTALLATION 240SX WITH AUTOMATIC TRANSMISSION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Support the transmission with a jack and remove the 4 rear mounting bracket bolts.
  3. Lightly lower the transmission to make room and pull out the dipstick tube.
  4. Remove or disconnect the following:
    • Negative battery cable
    • Connector bracket from the front mount bracket
    • Harness connector
    • Starter bolts
    • Starter
    To install:
  5. Install or connect the following:
    • Starter and torque the bolts to 30-37 ft. lbs. (40-50 Nm)
    • Harness connector
    • Connector bracket to the front mount bracket
    • Dipstick tube
    • Transmission into position
    • 4 rear mounting bracket bolts
    • Negative battery cable
  6. Remove the transmission jack
WITH MANUAL TRANSMISSION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Connector bracket from the front mount bracket
    • Harness connector
    • Starter bolts
    • Starter
    To install:
  3. Install or connect the following:
    • Starter and torque the bolts to 30-37 ft. lbs. (40-50 Nm)
    • Harness connector
    • Connector bracket to the front mount bracket
    • Negative battery cable
1.6L and 2.0L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Wiring at the starter
    • Bolts attaching the starter to the engine
    • Starter
    To install:
  3. Install or connect the following:
    • Starter and torque the bolts to 70 inch lbs. (8 Nm)
    • Starter electrical connections
    • Negaative battery cable
Maxima
  1. Remove or disconnect the following:
    • Negative battery cable
    • Air duct
    • Harness protector from the harness
    • Starter wiring at the starter
    • Starter-to-engine bolts
    • Starter from the vehicle

      Image 89612G12l Not Found

    To install:
  2. Install or connect the following:
    • Starter and torque the long bolt to 57-72 ft. lbs. (77-98 Nm) and the short bolt to 22-30 ft. lbs. (30-41 Nm)
    • Starter wiring
    • Harness protector
    • Air duct
    • Negative battery cable
Altima
  1. Remove or disconnect the following:
    • Negative battery cable
    • Air inlet tube
    • Harness bracket
    • Wiring at the starter
    • Starter
    To install:
  2. Install or connect the following:
    • Starter and torque the bolts to 60 inch lbs. (7 Nm)
    • Starter electrical connectors
    • Harness bracket
    • Air inlet tube
    • Negative battery cable

Nov 03, 2010 | 2003 Nissan Sentra

1 Answer

Hey my battery on my key died and my car wont start.Is there a way for me to manually start the car other than the push button? I drive a 2006 avalon limited edition


You donot want to be ripping down and pulling out wiring in the starter harness to repair what is obvious, that is a beautiful car not a wrecked vehicle, why would you not have it towed to get it repaired properly? Beside if there is any warrantee on this repair you will have definately void it by attempting to jump the starter system out.

Aug 01, 2010 | 2007 Toyota Avalon

1 Answer

How do i change the starter on a 2000 nissan altima


I hope this helps:

REMOVAL & INSTALLATION 240SX WITH AUTOMATIC TRANSMISSION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Disconnect the negative battery cable.
  3. Support the transmission with a jack and remove the 4 rear mounting bracket bolts.
  4. Lightly lower the transmission to make room and pull out the dipstick tube.
  5. Remove or disconnect the following:
    • Connector bracket from the front mount bracket
    • Harness connector
    • Starter bolts
    • Starter
    To install:
  6. Install or connect the following:
    • Starter
    • Starter bolts. Tighten the bolts to 30–37 ft. lbs. (40–50 Nm).
    • Harness connector
    • Connector bracket to the front mount bracket
    • Dipstick tube
    • Transmission into position
    • 4 rear mounting bracket bolts
  7. Remove the transmission jack
    • Negative battery cable
WITH MANUAL TRANSMISSION
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    • Negative battery cable
    • Connector bracket from the front mount bracket
    • Harness connector
    • Starter bolts
    • Starter
    To install:
  3. Install or connect the following:
    • Starter
    • Starter bolts. Tighten the bolts to 30–37 ft. lbs. (40–50 Nm).
    • Harness connector
    • Connector bracket to the front mount bracket
    • Negative battery cable
1.6L and 2.0L Engines
  1. Remove or disconnect the following:
    • Negative battery cable from the battery
    • Wiring at the starter
    • Bolts attaching the starter to the engine
    • Starter from the vehicle
    To install:
  2. Install or connect the following:
  3. Install the components in the reverse order of removal.
Maxima
  1. Remove or disconnect the following:
    • Negative battery cable from the battery
    • Air duct
    • Harness protector from the harness
    • Starter wiring at the starter
    • Starter-to-engine bolts
    • Starter from the vehicle Fig. 1: Starter location and mounting detail — Maxima with a manual transaxle 89612g12.gif
    To install:
  2. Install or connect the following:
    • Starter
    • Starter attaching bolts. Tighten the long bolt to 57–72 ft. lbs. (77–98 Nm) and the short bolt to 22–30 ft. lbs. (30–41 Nm).
    • Starter wiring
    • Harness protector
    • Air duct
    • Negative battery cable
  3. Start the engine a few times to make sure of proper operation.
Altima
  1. Remove or disconnect the following:
    • Negative battery cable from the battery
    • Air inlet tube
    • Harness bracket
    • Wiring at the starter
    • Bolts attaching the starter to the engine
    • Starter from the vehicle
    To install:
  2. Install the components in the reverse order of removal.
prev.gif next.gif

Jul 13, 2010 | 2000 Nissan Altima

1 Answer

How do you remove a 1999 Nissan Altima starter?


Nissan Car Altima & Sentra 1999-06 StarterRemoval & Installation
  1. Remove or disconnect the following:
    Negative battery cable Air duct Harness protector from the harness Starter wiring at the starter Starter-to-engine bolts Starter from the vehicle


  2. b53bb6c.jpg
    Fig. Starter location and mounting detail-3.0L Maxima with a manual transaxle


    b2eb267.jpg
    Fig. Starter location and mounting detail-3.5L Maxima

To install:
  1. Install or connect the following:
    Starter and torque the long bolt to 57-72 ft. lbs. (77-98 Nm) on Altima and Maxima and 41 ft. lbs. (55 Nm) on 350 Z. torque the short bolt to 22-30 ft. lbs. (30-41 Nm) Starter wiring Harness protector Air duct Negative battery cable
  1. Remove or disconnect the following:
    Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter

To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

1.6L & 2.0L Engines
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section.
  2. Remove or disconnect the following:
    Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negaative battery cable

1.6L, 1.8L & 2.0L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negative battery cable

1.8L & 2.0L Engines
  1. Before servicing the vehicle, refer to the Precautions section.
  2. Remove or disconnect the following:
    Negative battery cable Wiring at the starter Bolts attaching the starter to the engine Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 70 inch lbs. (8 Nm) Starter electrical connections Negative battery cable

2.4L & 2.5L Engines
  1. Remove or disconnect the following:
    Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

2.4L Engine
  1. Remove or disconnect the following:
    Negative battery cable Air inlet tube Harness bracket Wiring at the starter Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

2.5L Engine
  1. Remove or disconnect the following:
    Negative battery cable Air cleaner cover and duct Harness bracket Wiring at the starter Starter
To install:
  1. Install or connect the following:
    Starter and torque the bolts to 60 inch lbs. (7 Nm) Starter electrical connectors Harness bracket Air inlet tube Negative battery cable

3.5L Engines
  1. Remove or disconnect the following:
    Negative battery cable Air cleaner case (upper) and air cleaner to electric throttle control actuator tube. Harness protector from the harness Starter wiring at the starter Starter-to-engine bolts Starter from the vehicle

    42c548c.jpg
    Fig. Starter location and mounting detail-3.5L engine

continue...

Apr 05, 2010 | 1999 Nissan Altima

1 Answer

How to replace starter windstar 2003 V6 engine?


2003 Ford Truck Windstar 3.8L SFI 6cyl Repair Guide

Ford Windstar 1999-2003 - Starter Removal & Installation

  1. Disconnect the negative battery cable.
  2. Raise and support the vehicle safely.
    NOTE When removing the hard shell connector at terminal -S-, grasp the plastic shell. Do not pull on the wire.
  3. Disconnect the starter electrical harness.
  4. Remove the upper starter bolt.
  5. Support the starter and remove the lower bolt.
  6. Remove the starter from the vehicle.

    e1d1735.jpg

  7. Fig. The starter is located at the lower front of the engine, and is visible through the air duct

To install:
  1. Position the starter in the vehicle.
  2. Install the upper and lower bolts. Tighten to 15-20 ft. lbs. (20-27 Nm).
  3. Connect the starter electrical harness. Tighten the starter cable nut to 80-124 inch lbs. (9-14 Nm).
    NOTE When installing the hard shell connector, be careful to push it straight on and make sure it locks in position with a notable click or detent.
  4. Lower the vehicle.
  5. Connect the negative battery cable.

I really hope helps with this (remember rated this help) Good luck.

Dec 31, 2009 | 2003 Ford Windstar

1 Answer

Trying to find the location of the starter


Try looking on the front side of the engine between the oil filter and transmission.

Removal & Installation
  1. Remove or disconnect the following:
    • Negative battery cable
    • Starter harness connectors
    • Starter motor
To install:
  1. Install or connect the following:
    • Starter motor. Torque the bolts to 35 ft. lbs. (47 Nm).
    • Starter harness connectors. Torque the battery cable nut to 100 inch lbs. (11 Nm).
    • Negative battery cable

Jul 25, 2008 | 2000 Dodge Grand Caravan

Not finding what you are looking for?
1995 Jaguar XJ6 Logo

Related Topics:

130 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jaguar Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

yadayada
yadayada

Level 3 Expert

80339 Answers

SPEEDY CAR WORK SHOP...

Level 2 Expert

489 Answers

Are you a Jaguar Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...