Question about 1995 Ford F250

1 Answer

When I lock the hubs in there is a vibration and rumbling noise around 40mph and above

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 532 Answers

Probably rusted or worn out u-joints, in the front axel--left or right side

Posted on Dec 12, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What might be experienced by transaxil/transmission bearings wear? Rumbling or vibrations?


Kia is bad with wheel bearings ;.About 80 to 100k they start going bad. You have to check them physically with a dial gauge or know how to inspect them in other manners. They cause a rumbling sound when they start to go bad.

Feb 01, 2015 | 2007 Kia Amanti Sedan

1 Answer

Whining noise


Change the transaxle fluid & add a bottle of Red Lubgard

Also do the Power Steering Fluid & add Lubegard to that

Still there-- I would guess the trans is failing

Too high a speed for a wheel hub bearing,but possible

Mar 20, 2014 | 2007 Ford Edge SEL Plus

1 Answer

2004 ford freestar rumbling noise as I drive down the road at about 45-60mph - it sounds and feels a bit like I hit a rumble strip but it is coming from the engine


Sounds like a half shaft. Reach around behind each wheel and see if there is play in the shaft that leads from the wheel to the transmission. There should be no play. Other possibility is a bearing hub. Jack up car, grab the tire at 9 and 3 o'clock. Shake wheel if there is movement not from the tie rod then it is the bearing hub.

Jan 24, 2014 | Ford Freestar Cars & Trucks

1 Answer

Vibration rumbling coming from front end of a 1997 chevy blazer 4 wd


You still have hubs, and the front driveshaft. On some models the front driveshaft can be removed leaving the pinion forks/ ring in place. Some other Transfer cases may use an output shaft thats like the tailshaft on an automatic. This style could leave a gapping hole when you remove the front driveshaft.

Tires are a problem once a wear pattern is embedded in the tread. Sometimes a front to back rotation will reduce noise.

A caliper could be stuck skipping over a turning rotor.

Oct 31, 2012 | Cars & Trucks

1 Answer

2006 Kia Spectra is making a high frequency whistling noise, but it only makes the noise when slowing down from 40mph to 35mph if i apply the breaks the noise stops and if i accelerate the noise stops any...


Is it a squeel or a hum / rumble? 1st run your hands around the tyres especially the inside. Check for hi and low spots on the tyres. If the tyre is hi low hi low hi low it makes a shocking sound. if it is a squeel noise have they checked your brakes cause brakes have squeelers to let you know they need changeing

Oct 01, 2012 | 2006 Kia Spectra

1 Answer

2001 Sebring LXI convertable. Loud rumbling noise that increases as accelerating increases. Sounds like a rumble strip on the highway. I changed the tires with no change in the noise.


Bad hub bearing. Drive the car on a straght EMPTY road .@30 mph or when noise is audible, **** the wheel left than right (similar to a race car warming. tires) and listen if there is a change in the sound if so its a front bearing if not it should be a rear bearing .Jack the rear of the vehicle up and spin the tire holding onto the strut. Feel and listen for a vibration or noise. This should pinpoint that elusive noise.Let me know Good hunting

Apr 11, 2009 | 1998 Buick Park Avenue

1 Answer

Van rumbles and vibrates


Does this van have a carrier bearing in the center of the driveshaft? If it does this could be your culprit,you can tell if it has a carrier bearing by looking at the drive shaft in the middle it will around the driveshaft and bolted to floor support of the van.

Mar 29, 2009 | 2002 Ford E-Series

1 Answer

Rumbling noise at 30mph and above is it the cv joints?


sounds more like rotors or hub bearings cv joints make a clicking noise while turning when their going bad

Feb 26, 2009 | 1997 Oldsmobile Aurora

Not finding what you are looking for?
1995 Ford F250 Logo

Related Topics:

100 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

fordexpert

Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...