Question about 2002 Oldsmobile Bravada

1 Answer

Power Steering How hard is it to replace power steering hoses?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 83 Answers

It's not all that complicated, however the clearance (or lack of it) involved in getting the lines off the power steering rack may drive you a little nuts. Getting the lines off the pump isn't that much of an issue. I would call this job not "difficult", but time consuming.

Posted on Dec 10, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change the power steering pressure hose on a 1995 Buick Regal gran sport


How to Remove a Power Steering Hose the Easy way, Tool ...

? 7:49
www.youtube.com/watch?v=OVBFrMcmV7Y
Dec 12, 2013 - Uploaded by Artistry Photography How to Remove a Power Steering Hose the Easy way, Tool Review ... The removal of this power steering pressure hose is a hard job but the ...

Replacing A Leaking Power Steering Hose - YouTube

? 2:38
www.youtube.com/watch?v=l1boEHtawcM
May 12, 2010 - Uploaded by Scotty Kilmer replace the whole hose assembly, they hold 1600 psi pressure, you can't .... i was told i need a new power steering pressure hose for my 2003 .

Oct 16, 2015 | Buick Cars & Trucks

1 Answer

Power steering fluid leak in 99 Toyota Corolla


look for split in the hard line where fluid is leaking. If you see split, change the line only. make sure power steering reservoir is filled and rack and pinion is full (charge with steering wheel left/right motion). You should be able to remove wheel and inside wheel panel to see power steering fluid shooting out of any hole. There is hydraulic pressure on the lines.

Apr 03, 2014 | 2003 Kia Spectra

1 Answer

Hard steering


The high and/or low side power steering hoses are failing.
Locate it with the help of a white tissue wipes.
Replace it ASAP before it burst and paint the driveway.

Jan 19, 2014 | Oldsmobile Alero Cars & Trucks

2 Answers

I have a 1997 toyota camry that was reported to have a power steering hose leak at 125,000 K and when I took it to another mechanic at 127,000 K he told me that I need a new power steering pump and power...


POWER STEERING PUMP OR HOSE HAS NO SET TIME OR MILEAGE TO FAIL WHEN THEY WEAR OUT THEY WILL FAIL ANY TIME.I WOULD HAVE POWER STEERING HOSE REPLACE FIRST.IF YOUR STEERING WAS NORMALWORKING GOOD BEFORE HOSE RUPTURE NO NOISES OR HARD STEERING.REPLACE POWER STEERING HOSE.BECAUSE POWER STEERING PUMP AND RACK PINION UNIT GOING TO COST RIGHT MUCH.ALSO BY IT BEING A IMPORT.

Feb 15, 2010 | 1997 Toyota Camry

1 Answer

Need to replace high pressure power steering hose on 2004 Monte Carlo SS. Need tips to effectively do the job myself. Tools needed, tricks to make the job easier, what not to do...etc. Thank yiou so much...


Power Steering Line/Hose: Service and Repair
Pressure Hose
Power Steering Pressure Pipe/Hose Replacement (3.8L)
Removal Procedure
1. Place a drain pan under the vehicle.
2. Remove the accessory drive belt.
3. Raise and support the vehicle. Refer to Vehicle Lifting.
4. Remove the tire and wheel assembly.
5. The power steering pressure hose is the lower hose at the power steering gear.
Remove the power steering pressure hose from the power steering gear.
6. Remove the power steering pressure hose from the power steering pump.
7. Remove the power steering pressure hose from the clamps on the power steering gear.
8. Remove the power steering pressure hose from the vehicle.
Installation Procedure
1. Install the power steering pressure hose to the vehicle.
2. Install the power steering pressure hose to the clamps on the power steering gear.
Notice: Refer to Fastener Notice in Service Precautions.
3. Install the power steering pressure hose to the power steering pump.
^ Tighten the fitting to 27 Nm (20 ft. lbs.).
4. Install the power steering pressure hose to the power steering gear.
^ Tighten the pressure hose fitting to 27 Nm (20 ft. lbs.).
5. Install the tire and wheel assembly.
6. Remove the drain pan from under the vehicle.
7. Lower the vehicle.
8. Install the accessory drive belt.
9. Fill the power steering system with power steering fluid.
10. Bleed the power steering system.
11. Inspect the power steering system for leaks.

00d203e.jpg

Sep 15, 2009 | 2004 Chevrolet Monte Carlo

2 Answers

How to replace power steering pump


2004 Pontiac Grand Prix V6-3.8L VIN 2

Power Steering Pump: Service and Repair
Power Steering Pump Replacement
NOTE: The content of this article / image reflects the changes called out by TSB: 05-02-32-004.

Power Steering Pump Replacement
Removal Procedure
1. Remove the accessory drive belt.
2. Raise and support the vehicle. Refer to Vehicle Lifting.
3. Remove the tire and wheel assembly.
4. Disconnect the power steering pressure hose from the power steering pump.
5. Disconnect the power steering return hose from the power steering pump.
6. Disconnect the harness connector (4) from the power steering pump (1).
7. Remove the power steering mounting bolts from the power steering pump.
8. Remove the power steering pump from the engine.
9. Remove the power steering pump pulley from the power steering pump.
10. Remove the power steering pump reservoir from the power steering pump.
Installation Procedure
1. Install the power steering pump reservoir to the power steering pump.
2. Install the power steering pump pulley to the power steering pump.
3. Position the power steering pump to the engine.
Notice: Refer to Fastener Notice in Service Precautions.
4. Install the power steering pump mounting bolts.
Tighten the bolts to 25 Nm (18 ft. lbs.).
5. Connect the power steering pressure hose to the power steering pump.
6. Connect the power steering return hose to the power steering pump.
7. Install the harness connector (1) to the power steering pump (4).
8. Install the accessory drive belt.
9. Fill the power steering system with fluid.
10. Bleed the power steering system.
11. Operate the power steering system and inspect for power steering system leaks.

d2ff628.jpg
949e18c.jpg
a9ee201.jpg

Sep 07, 2009 | 2004 Pontiac Grand Prix

2 Answers

My power steering pressure hose has a leak.


i pERSONALY WOULD REPLACE IT MYSELF EVEN WITHOUT MY 30yrs Of Experience in this Field. I have Enclosed Instructions for you to use. PLEASE dont Forget to RATE me As MOST folks DONT remember to that is how WE Get our Ratings such as GURU THANK YOU and Good Luck On The Job, Dont PAY a dime If YOU CAN > D I Y

REMOVAL PROCEDURE
  1. Remove the power steering pressure hose (2) from the power steering pump (1).
  2. Raise the vehicle on a hoist. Refer to Vehicle Lifting.
  3. Remove the front exhaust pipe, automatic transmission only. Refer to Intermediate Pipe Replacement in Exhaust System
  4. Remove the power steering pressure hose (1) from the power steering gear (3).
  5. Remove the power steering hose retainer (2).
  6. Remove the power steering pressure hose (1) from the vehicle
    1. Install the power steering pressure hose (1) to the vehicle
    2. Install the power steering hose retainers (2). NOTICE: Refer to Fastener Notice in Service Precautions.
    3. Install the power steering pressure hose (1) to the power steering gear (3). Tighten the fitting to 27 Nm (20 ft. lbs.).
    4. Install the front exhaust pipe, if removed. Refer to Intermediate Pipe Replacement in Exhaust System.
    5. Lower the vehicle.
      1. Install the power steering pressure hose (2) to the power steering pump (1). Tighten the fitting to 27 Nm (20 ft. lbs.).
      2. Bleed the power steering system. Refer to Bleeding Power Steering System in Service and Repair of Steering.

Mar 27, 2009 | 1999 Pontiac Sunfire

1 Answer

Lost power steering


power steering pumps can go out w/ no warning. on your model car you can replace it easily if you are handy and patient. loosen belt and hoses. label hoses, remove pump and replace in reverse. hope this helps

Nov 01, 2008 | 1992 Isuzu Rodeo

1 Answer

Power steering pump


not too hard if you have some tools.
  1. Raise and support the vehicle.
  1. Remove the power steering pump pulley (3A733). Refer to the procedure in this section.
  1. Place a drain pan under the power steering pump (3A674).
  1. Remove the power steering pressure hose bolt from the power steering pump. Place the power steering pressure hose (3A719) up and out of the way.
  2. Remove the two power steering reservoir pump hose bolts. Place the power steering reservoir pump hose up and out of the way.
  3. Remove the three front power steering pump bolts.
    1. Remove the rear power steering pump bolt.
    1. Remove the power steering pump from the vehicle.

Aug 21, 2008 | 1998 Mercury Villager

Not finding what you are looking for?
2002 Oldsmobile Bravada Logo

116 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

80263 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...