Question about 1999 Pontiac Bonneville

1 Answer

What do I have to remove to access blend door actuator

What do I have to remove to access and replace the passenger side blend door actuator for 1999 Bonneville SLE

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Sergeant:

    An expert that hasĀ over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 248 Answers

Very lenghty process. too long to describe here....go to Bonneville Forums read the text and follow linked there at the bottom....very good and detailed....I'm doing that right now,,,,it is a bugger,

Posted on Apr 16, 2010

  • cg522000 Jul 12, 2011

    this was very helpful thank cg

×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Location of passenger side blend door actuator on 2006 mercury mountaineer auto controls, 6 cylinder


Temperature Blend Door Actuator - RH, EATC Removal and Installation
  1. Remove the RH floor console finish panel.
  1. Lower the glove compartment.
  1. Disconnect the RH temperature blend door actuator electrical connector.
  2. Remove the 3 RH temperature blend door actuator screws.
    1. Remove the RH temperature blend door actuator.
2006 2010 Ford Explorer NO Heat Passenger Temp Actuator Replacement same as mountaineer

Jun 19, 2017 | Mercury Cars & Trucks

2 Answers

How do I find the ac heat acuator on a 2001 Pontiac Bonneville sle.


How To Install Replace AC Heater Temperature Actuator ...

? 4:40
https://www.youtube.com/watch?v=mVP09M7hLB4
Jul 21, 2014 - Uploaded by 1A Auto Parts
http://www.1aauto.com/temperature-blend-door-actuator/i/1ahcx00293 ... How To Remove Install Door Chevy Monte Carlo Pontiac Grand Prix ...

GM Blend Door Actuator Repair (Saturn, Chevy, GMC, Buick ...

? 4:28
https://www.youtube.com/watch?v=fER3ZqnYLZg
Jul 11, 2014 - Uploaded by willmacneill
The procedure is the same for most GM blend door actuatorsfrom 1990-2013 (found in many vehicles made by Chevy, GMC, Buick, Pontiac, ...

Mode/Temperature Door Actuators May Fail : Pontiac ...




Jan 16, 2016 | Pontiac Cars & Trucks

1 Answer

How do you remove a blent door actuater from 2001 pontiac bonnevile


I never heard about a need to "reset" or replace a blend door.

If a/c, you probably need some Freon recharge. My 2005 Bonneville had this problem with the a/c. I looked at the blend doors for hours, before getting a clue about the low Freon. You'll probably need to go to the dealer or an a/c specialist to have it checked. It may ony need 1/2 a can of Freon to fix.

Apr 13, 2014 | 2001 Pontiac Bonneville

3 Answers

Driver side blowing hot air passenger side blowing cold air


I'm having the same problem except on mine it's the driver's side that's blowing cold. Do you have the pictures in a finer resolution? I can't make them out and when I zoom, they are too grainy. Does the replacement require removing the dashboard? What's the general cost of the acuators? Are they readily available at like NAPA or other parts stores?

Nov 26, 2011 | 2006 Kia Amanti

1 Answer

Problem with dual zone heating only one side i check control thermost botton is ok


Sounds like the blend door actuator. It separates the driver and passenger side from getting air on the AZC system. Here are some instructions on replacing it:
The passenger side blend door actuator is used on all models equipped with Automatic Zone Control (AZC). This actuator is located on the front of the HVAC housing to the right of the floor panel transmission tunnel and cannot be removed from the passenger compartment without instrument panel or HVAC housing removal.

NOTE: This procedure is for AZC Systems (Passenger side only).

  1. Disconnect and isolate the battery negative cable.
  2. Remove the glove box door. See: Body and Frame\Interior Moulding / Trim
  3. Remove the lower I/P glove box door surround panel.
  4. Remove the dash assembly. See: Body and Frame\Interior Moulding / Trim\Dashboard / Instrument Panel\Service and Repair\Instrument Panel Assembly
  5. Remove the HVAC assembly. See: Housing Assembly HVAC\Service and Repair
  6. Unplug the wire harness connector from the blend door actuator.
  7. Remove the 2 screws that secure the blend door actuator to the HVAC housing.
  8. Remove the blend door actuator from the HVAC housing.
INSTALLATION - AZC (Passenger side only)


  1. In stall the blend door actuator on the HVAC housing and tighten the two mounting screws to 2.2 Nm (20 in. lbs.).
  2. Plug in the wire harness connector to the blend door actuator.
  3. In stall the HVAC unit into the vehicle. See: Housing Assembly HVAC\Service and Repair
  4. Install the instrument panel assembly into the vehicle. See: Body and Frame\Interior Moulding / Trim\Dashboard / Instrument Panel\Service and Repair\Instrument Panel Assembly
  5. Evacuate the HVAC system.
  6. Recharge the HVAC system.
  7. Connect and the battery negative cable.
Hope it helps! If you need more, just send me an email at familyguy77351 at yah I wil be glad to finish helping you with more detail.

Dec 12, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Afternnon, just wondering about the best way to locate the blend doors in the hvac box without ripping out the dash on my 2000 jeep grand cherokee. Thanks in advance. Duane


y9ou can gain access to the driver side blend door actuator by removing the glove box. The actuator will be in the left corner of the glove box opening. If you remove the actuator you will be able to turn the pin. If you can turn it 360 degrees the blend door is broke.

If your lucky its only the drivers side. If you get the repair kit from chrysler it will come with instructions with pictures on how to replace the blend door without pulling the HVAC unit/Dash. If the passenger side is broken the HVAC unit will need to be removed.

Heater treater (google them) also have a metal blend door replacement and instructions online on how to replace them without pulling the HVAC housing.

Nov 28, 2010 | 1999 Jeep Grand Cherokee

2 Answers

When I turn the heat on the drivers side only kicks out cold air while the passenger side kicks out hot air...


The blend door is not working right or the in car air temperature sensor is faulty.
Removal & Installation Air Inlet Door Vacuum Motor To Remove:
  1. Remove the instrument panel.
  2. Remove the air inlet door motor mounting screws. CAUTION
    Do not attempt to bend any part of the air inlet duct door lever.
  3. Rotate and remove the air inlet door vacuum control motor.
To Install:
  1. Rotate and install the air inlet door vacuum control motor.
  2. Install and tighten the mounting screws.
  3. Install the instrument panel.
Defroster Door Vacuum Motor To Remove:
  1. Remove the passenger air bag module from the instrument panel.
  2. Disconnect the vacuum line and remove the mounting screws. CAUTION
    Do not attempt to bend any part of the defroster airflow mode door lever.
  3. Rotate and remove the vacuum control motor from the defrost door lever.
To Install:
  1. Rotate and install the vacuum control motor on the defrost door lever.
  2. Install and tighten the mounting screws.
  3. Connect the vacuum line to the vacuum control motor.
  4. Install the passenger's air bag module.
Floor Console Register Duct Vacuum Motor To Remove:
  1. Remove the floor console.
  2. Remove the right-side instrument panel insulator.
  3. Working from the passenger's footwell, disconnect the vacuum hose.
  4. Remove the screws and the floor console register duct vacuum control motor. CAUTION
    Do not attempt to bend any part of the floor console register duct door lever.
  5. Rotate and remove the vacuum control motor from the floor console register duct door.
To Install:
  1. Rotate and install the vacuum control motor on the floor console register duct door.
  2. Install and tighten the mounting screws.
  3. Connect the vacuum hose to the floor console register duct vacuum control motor.
  4. Install the insulator under the dash.
  5. Install the floor console.
Panel/Floor Door Vacuum Motor To Remove:
  1. Working through the driver footwell, remove the two screws and the shield. CAUTION
    Do not attempt to bend any part of the airflow mode door lever.
  2. Label and disconnect the two vacuum hoses.
  3. Remove the mounting screw.
  4. Lift, rotate and remove the panel/floor door vacuum control motor from the door lever.
To Install:
  1. Install the panel/floor door vacuum control motor on the door lever.
  2. Install and tighten the mounting screw.
  3. Connect the vacuum hoses in their original positions.
  4. Install the shield on the vacuum motor.
Auxiliary Air Distribution Blend Door Actuator To Remove:
  1. Remove the right rear quarter trim panel access panel. Auxiliary climate control housing removal and installation ford-10-00-4589.gif

  2. Remove the auxiliary air distribution blend door actuator screws.
  3. Disconnect the auxiliary air distribution blend door actuator connector.
To Install:
  1. Connect the auxiliary air distribution blend door actuator connector.
  2. Install the auxiliary air distribution blend door actuator screws.
  3. Install the right rear quarter trim panel access panel.
Auxiliary Temperature Blend Door Actuator To Remove:
  1. Remove the right rear quarter trim panel. Auxiliary climate control housing removal and installation ford-10-00-4589.gif

  2. Disconnect the temperature auxiliary temperature blend door actuator connector.
  3. Remove the temperature auxiliary temperature blend door actuator screws.
  4. Remove the temperature auxiliary temperature blend door actuator.
To Install:
  1. Install the temperature auxiliary temperature blend door actuator.
  2. Install the temperature auxiliary temperature blend door actuator screws.
  3. Connect the temperature auxiliary temperature blend door actuator connector.
  4. Install the right rear quarter trim panel.
--- In-Car Temperature Sensor Removal & Installation To Remove:
  1. Remove the instrument cluster finish panel.
  2. Disconnect the in-vehicle temperature sensor connector.
  3. Disconnect the in-vehicle temperature sensor aspirator tube.
  4. Remove the in-vehicle temperature sensor screws.
  5. Remove the in-vehicle temperature sensor.
To Install:
  1. Install the in-vehicle temperature sensor.
  2. Install the in-vehicle temperature sensor screws.
  3. Connect the in-vehicle temperature sensor aspirator tube.
  4. Connect the in-vehicle temperature sensor connector.
  5. Install the instrument cluster finish panel.
prev.gif next.gifprev.gif next.gif

Oct 07, 2010 | 2004 Ford Freestar

2 Answers

200 Jeep Laredo..Air is cold and fan is blowing,


there is a blend door actuator for the laredo and if is bad the air wont come out here is a pic of what it looks like and how to get to it


The single zone heater-A/C system is equipped with a single blend door actuator. The dual zone system has two blend door actuators, one for the driver side blend-air door and one for the passenger side blend-air door.
7d2da02.gif
  1. Disconnect and isolate the negative battery cable.
  2. Remove the glove box from the instrument panel.
  3. Remove the three screws that secure the blend door actuator to the passenger side of the HVAC air distribution housing .
  4. Remove the blend door actuator from the air distribution housing and disconnect the HVAC wire harness connector from the actuator.
  5. Remove the blend door actuator from the vehicle
to instal
  1. Position the blend door actuator into the vehicle.
  2. Install the blend door actuator onto the passenger side of the HVAC air distribution housing . If necessary, rotate the actuator slightly to align the splines on the actuator output shaft with those on the blend door cam .
  3. Install the screws that secure the blend door actuator to the passenger side of the air distribution housing . Tighten the screws to 17 inch lbs. (2 Nm).
  4. Connect the HVAC wire harness connector to the blend door actuator.
  5. Install the glove box into the instrument panel.
  6. Reconnect the negative battery cable.

Sep 09, 2009 | 1998 Cadillac Seville

2 Answers

Hot air comes out the passenger side when air condirioning is on.


The control module or actuator is most likely the cause. You can manually set it for cold air until winter. Actuator is under the dash right by the blower.

Aug 20, 2009 | 2004 Chevrolet Silverado

2 Answers

Heat flowing on passenger side only


your actuatior foe the drivers blend door is stuck. try unhooking battery for a few minutes have both on heat and hook back up and start up. the actuators will run thru a learn mode and sometimes this will free up.if not you will need an actuator

Dec 09, 2008 | 2005 Chevrolet Silverado

Not finding what you are looking for?
1999 Pontiac Bonneville Logo

1,939 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

79865 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...