Question about 1994 Ford Crown Victoria

1 Answer

Will the brain in my 1994 crown vic run with a 4.6 from a cougar?because i swaped my blown motor out with the cougar motor

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 83 Answers

It shouldn't have any issues at all. So long as the build dates of both engine line up closely, your internal componants should be compatable. If there is any issue, you'll get a check engine light. If the year of build is not the same/close, and/or if you find a lot of sensor plugs that do not match from engine to engine, I would suggest further research to make sure all the internals are the same. Other than that, it should work fine. the Stick

Posted on Dec 10, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Rebuilding motor 96 crown Vic


Buy a used factory repair manual so you know the info is accurate. You can find used factory manuals on eBay motors.

Jul 16, 2016 | 1996 Ford Crown Victoria

1 Answer

Hello? Emission problem 1994 crown vic here...


I owned one of these. There is a groove under the butterfly horn of the throttle. There are 8 bolts and a $10 gasket. Often the EGR passage is clogged and it throws off the calibrations and when you clean this groove the engine will run much better.

Jul 21, 2014 | 1994 Ford Crown Victoria

1 Answer

I put a 2003 transmission out of a crown vic into a 1998 crown vic then wired the vss into the output shaft sensor little did i know that made my speedometer reading double how can i fix this will swaping...


I doubt it.
The computer for the 2003 would not follow all of the wiring patterns in the 98 harness not to mention the chip would be different.

Oct 15, 2012 | Cars & Trucks

1 Answer

1994 ford crown vic front pass. side power window regulator...


Yes it is. They will need to be drilled out. Thats the best way, some people try to put bolts on, but I dont advise it.

May 12, 2010 | 1994 Ford Crown Victoria

1 Answer

1994 crown vic, not PI, is not charging. Put in


there is a alternator fuse on the relay center under the hood that is a large fuse rated i think at like 140 amps check it it probably blew

Feb 07, 2010 | 1994 Ford Crown Victoria

1 Answer

Rear and interior dashboard lights don't work 1994 Crown Vic.


Easy stuff first. Try replacing the #9 fuse on the interior fuse panel. This fuse protects the instrument panel, license, parking and tail light circuits. The panel is located under the dash to the left of the steering column. You will need to pry off the cover on the panel to access the fuses. The fuse you want is a 15 amp fuse located directly under the turn signal flasher. It should be easy to figure out which fuse it is because it will be 'blown' or open. This is easy to determine just by looking at the fuse once it's removed. And, if you aren't sure what's what, I'm sure you can find a diagram of this fuse panel somewhere on the Internets if you look around a little. I took this info out of the Owner Manual from my own '94 Vic. If this doesn't solve the problem I would suggest taking your Vic to a shop and letting them take a look at it.

Dec 19, 2009 | 1994 Ford Crown Victoria

2 Answers

Wiper motor replacement for a 99 crown vic


I replaced the same part on a 1994 Crown Vic. There are a few bolts which go through rubber mounts on the firewall and that is how the wiper motor fits against the firewall. There is a clip on the wiper drive that must be pressed and slid off the wiper shaft. The hardest part was getting clearence between the engine and wiper motor. If I remember there was a way to turn the wiper case to clear the engine. I have asked myself why this was engineered like this? There is nothing important in the way that 3/4" of clearance could have been given for removal.

May 06, 2009 | 1999 Ford Crown Victoria

3 Answers

94 crown vic driver power window does not work can


The window regulator can be broke. Its made of plastic and they break often.

May 03, 2009 | 1994 Ford Crown Victoria

Not finding what you are looking for?
1994 Ford Crown Victoria Logo

86 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

80407 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

fordexpert

Level 3 Expert

5687 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...