Question about 2002 Chevrolet Silverado

1 Answer

Reset ABS Light - 2002 Chevrolet Silverado

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 1,608 Answers

The only way to reset the ABS light is to get the codes and repair the problem.You have to use a scan tool to reset them.If you do not repair it it will come back on.hope this helps.

Posted on Dec 10, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Abs replaced axle shaft @ abs cable abs light still on after reset


The ABS fault light will stay on until the problem is repaired, read the fault code and diagnose it again.

May 14, 2016 | 2003 Mazda Protege

1 Answer

Replaced brakes on 1995 Ford Taurus and now ABS light is on and ABS is disabled


The ABS light only comes on because of a fault. You need the ABS control module scanned for the code that set when the light comes on. There is no RESET

Mar 28, 2014 | 1995 Ford Taurus

1 Answer

How to reset abs light in a subaru forester


The ABS light on your vehicle will self-reset, once the condition causing the light to illuminate is rectified.
Reasons for the ABS light coming on are:
  1. Worn brake pads;
  2. Worn calipers (beyond tolerance);
  3. Defective ABS unit;
  4. Low brake fluid level;
  5. Defective master cylinder;
  6. Brake fluid leak.
It is important that whatever condition is causing the ABS light to illuminate is corrected as soon as possible, as it indicates a potential hazardous condition exists with your vehicle.

Jun 29, 2012 | 1998 Subaru Forester

2 Answers

Jumped started c180 now abs is on


Usually, the two are not related. But, if the abs module is damaged it could be throwing an abs light erroneously. Usually an abs light means that a sensor is bad or not picking up a signal from the sensors at the wheels. It is normal for the abs light to light when the ignition is on but the car hasn't started as a bulb check only.

Dec 12, 2011 | 1994 Mercedes-Benz C-Class

1 Answer

Abs light still dose go off after fitting to new abs sensors?


new abs and speed sensor fitted light still on do codes have to be cleared

Nov 27, 2011 | Cars & Trucks

1 Answer

How do i reset my abs warning light on my 2000 pontaic montana?\


ABS light on - means your Brake ABS system is not working.
Some autoparts stores, like AutoZone will scan you car for error codes. I recall that they can scan for engine and chassis codes, like the ABS system. They can also reset the light.

The bad news is that when the ABS light stays on, there really is something wrong with your ABS. You should get the car scanned and an estimate for the repair.

Apr 15, 2011 | Pontiac Montana Cars & Trucks

2 Answers

1999 Ford Ranger with 4 wheel ABS. I replaced the brakes on all four wheels and the rear wheel cylinders. The rear brake lines were open individually for a very brief time, and bled conventionally. I would...


The brake pads and shoes are not elec., your abs light is on because your abs computer pick up a bad signal from one of your abs sensor's,, take it to any auto parts or some one like autozone where they can do a code reading and get back us with the code so we can help you diag. your trouble code.

Jun 14, 2010 | 1999 Ford Ranger SuperCab

1 Answer

How do I reset the ABS light on an 02 Rendozvous?


There are dedicated scanners for resetting the ABS light.

Try Actron Brakescan @

http://www.amazon.com/s/ref=nb_sb_ss_i_0_11?url=search-alias%3Daps&field-keywords=actron+abs+brakescan&x=0&y=0&sprefix=Actron+abs+

Good luck.

May 23, 2010 | 2002 Buick Rendezvous

1 Answer

2001 alero abs light on


ur brain in the car needs to be reset if that does not work u might have to replace ur abs system u can take ur car to a local auto zone or advance auto and they can reset it and see if there is a error code with the light also some times the longer the light stays on or refuses to reset says there is a problem with u abs system

Nov 14, 2008 | 2001 Oldsmobile Alero

Not finding what you are looking for?
2002 Chevrolet Silverado Logo

Related Topics:

901 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

81285 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...