Question about 2004 Buick LeSabre

1 Answer

The blower motor is pass. side under the glove box... Correct?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 986 Answers

It can be on the engine side right in the middle

Posted on Dec 10, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do you replace the a/c heater fan motor in a 1998 honda civic?


this is not hard, you will need to remove the glove box and then lower cover if it has one this is located on the pass/side under the dash, remove the connector from the blower motor then remove the screws holding the motor to heater box blower should come right out and reverse directions to install new one.

Jan 12, 2011 | 1998 Honda Civic

2 Answers

I cant find the blower motor


If you mean the climate control blower motor, it's usually under the dash on the passenger side on Hondas.

1990-93 Accord
  1. Disconnect the negative battery cable. If so equipped, disable the Supplemental Restraint System (SRS).
  2. Remove the glove box.
  3. Remove the glove box frame (lower support) Fig. 2: Remove the glove box and frame 86806004.gif

  4. If not equipped with air conditioning:
    1. Remove the three screws and remove the heater duct.
    2. Remove the blower mounting nuts. Unplug the wiring from the blower motor, resistor and recirculation control motor, then remove the blower assembly.
  5. If equipped with air conditioning:
    1. Lift the carpet in the passenger compartment. Remove the side cover (kick panel).
    2. Remove the control unit bracket nuts; unplug the five connectors and remove the control unit bracket.
    3. Remove the retaining band, then remove the blower lower covers. Do not break the tabs on the lower covers.
    4. Remove the retaining nuts and remove the blower assembly. Fig. 3: Air conditioned models require the removal of the control unit. Handle it carefully 86806005.gif
      Fig. 4: Remove the lower covers from the blower unit 86806006.gif
      To install:
  6. Install the blower unit and tighten the retaining nuts.
  7. On air conditioned vehicles:
    1. Install the lower covers and the retaining band.
    2. Install the control unit bracket and carefully engage the wiring connectors to their proper location.
    3. Install the kick panel and reposition the carpet.
  8. Connect the wiring to the blower assembly. For non-air conditioned vehicles, install the air duct and tighten the screws.
  9. Install the glove box frame and install the glove box. Note that some of trim on the frame is held with 2-sided tape; replace the tape when reassembling as necessary.
  10. If applicable, enable the SRS.
  11. Connect the negative battery cable.
1988-91 Prelude
  1. Disconnect the negative battery cable.
  2. Remove the glove box and frame (lower support).
  3. Remove the 4 screws and remove the heater duct. Fig. 5: The glove box and frame are secured by several small screws 86806007.gif

  4. Remove the 3 mounting bolts.
  5. Unplug the wiring connectors from the blower motor, resistor and recirculation controller. Remove the blower motor assembly.
  6. Reinstall in reverse order. Make certain the blower mating surfaces are tightly sealed.

Jan 08, 2011 | 1992 Honda Accord

1 Answer

Location of heater resister on 2005 Chevy Inpala with 3.4 motor


under dash on pass side under glove box area remove panel( 8mm i think) then locate blower and follow wires back to the resistor (few inches away)

Jan 03, 2011 | 2004 Chevrolet Impala

1 Answer

How do I change a blower motor in a chrysler Town and country


Hello, to change the blower motor resistor follow this steps:
  1. Disconnect and isolate the battery negative cable.
  2. Open the glove box.
  3. Flex both sides of the glove box bin inward near the top far enough for the rubber glove box stop bumpers to clear the sides of the glove box opening, then roll the glove box downward.
  4. Reach through the glove box opening to access and disconnect the instrument panel wire harness connector for the blower motor resistor from the resistor connector receptacle.Blower motor Resistor
  5. Reach through the glove box opening to access and disconnect the blower motor pigtail wire connector from the resistor connector receptacle.
  6. Remove the two screws that secure the blower motor resistor to the evaporator housing.
  7. Remove the blower motor resistor from the evaporator housing.

Thanks

Aug 25, 2010 | 2006 Chrysler Town & Country

1 Answer

How do i replace the heater blower motor


Remove the glove box.Then remove the glove box lower frame.The blower motor will be on the
right hand side under the dash.Remove three 10 mm screws.After removing the screws pull the
blower motor forward and up.There will be three harnesses connected in the lower right side
of the blower.

Nov 06, 2009 | 1992 Honda Accord

2 Answers

How to change front blower motor in a 2003 dodge caravan


Removal & Installation
CAUTION The Supplemental Inflatable Restraint (SIR) system must be disarmed before removing the blower motor assembly. Failure to do so may cause accidental deployment of the air bag, resulting in unnecessary SIR system repairs and/or personal injury.

  1. Disconnect and isolate the negative battery cable, then wait 2 minutes before proceeding with the removal. This will effectively disable the air bag system preventing possible personal injury.
  2. Remove the glove box from the instrument panel
d6b70fa.gif
The blower motor is located behind the glovebox, behind the blower motor cover

  1. Remove the A/C-heater blower motor cover.
  2. Disconnect the blower motor wiring connector.
  3. Remove the blower motor wiring grommet and feed the wiring through the blower motor housing.
  4. Remove the blower motor mounting screws.
0e0729c.gif
Once the cover is removed, unplug the electrical connector and push it through the opening in the housing

1ed158c.gif
The blower motor is secured to the housing with three small screws

  1. Allow the blower motor assembly to drop downward to clear the instrument panel and remove from vehicle.
To install:
  1. Place the blower motor assembly into position on the A/C-heater unit and tighten the mounting screws.
  2. Route the blower motor wiring through the blower motor housing and seat the wiring grommet in the hole of the blower motor housing.
  3. Reconnect the blower motor electrical connector.
  4. Install the A/C-heater blower motor cover.
  5. Install the glove box into the instrument panel.
  6. Reconnect the negative battery cable. Check blower motor operation.

Oct 12, 2009 | 2003 Dodge Caravan

3 Answers

A/C BLOWER


most likely its the blower motor resister and is located behind the glove box. there are a few philips head screws you will need to remove inside the glove box and under the glove box to get the glove box out after that it should be a walk in the park

Mar 09, 2009 | 1998 Lexus Gs 400

1 Answer

Blower motor replacement on 02 chevy S10


I believe you have to pull the dash apart on pass side under glove box to get to it.. Sorry

Dec 21, 2008 | 2002 Chevrolet S-10

1 Answer

Have no air at all coming from blowers on Honda civic type r


transistor then. Its the same thing as the blower motor resistor just a different name. This is a easy fix. Simple if you have good instructions.

First you need to remove the dashboard lower cover. This is located under the glove box covering the blower motor and your ECM/PCM. Gently pull down at the edges nearest the glove box. 4 clips should pop. Now just pull the cover tword you and it will slide out of the holders.

Now you need to remove the glove box. Do this by opening it. Look on the side of the glove box you will see one bump stop on each side. Pull those in tword the middle of the glove box. Now it should hang all the way down. You will see two bolts around the hing of the glove box. remove both of those bolts. They should be a 8 or a 10mm bolt.

You should be able to see the power transistor now It will be to the lower left side of the blower motor. It is held in by two screw and has 4 wires going into it. It will be facing outward tword you.

The color of the wires going into the motor will be black, blue/black, blue/yellow, and blue red.

You may not even have to take the glove box out. Once you take out lover dashboard cover check and see if you can see the blower transistor.

If their is anything else i can do let me know.

Dec 10, 2008 | 2002 Honda Civic

Not finding what you are looking for?
2004 Buick LeSabre Logo

Related Topics:

29 people viewed this question

Ask a Question

Usually answered in minutes!

Top Buick Experts

yadayada
yadayada

Level 3 Expert

78919 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Buick Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...