Question about 1999 Isuzu Rodeo

1 Answer

WHERE IS CAMSHAFT POSITION SENSOR ON 2000 RODEO 3.2 V-6?

Posted by on

  • thehenyans Dec 10, 2009

    THANKS FOR THE INPUT. EVERYTHING ELSE I'VE READ SAYS REAR OF DRIVERSIDE HEAD.? IS IT UNDER THE VALVE COVER?

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Master
  • 986 Answers

Left front of the engine

Posted on Dec 10, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

What are the probable causes of camshaft sensor DTC?


Camshaft sensors do go bad. They can go bad slowly, so you don't notice the badness until your engine stalls, but restarts, or you get a "check engine" light. They are not expensive or hard to replace.

Nov 10, 2015 | 1999 Isuzu Rodeo

2 Answers

Where is the camshaft position sensor for


They are located on each head if im not mistaken on the corner near the air intake boot that goes to air filter. The cylinder head close to the radiator is 2 4 6.

Sep 20, 2014 | 2000 Lexus ES 300

1 Answer

Camshaft position sensor


I put a 2000 3.2 litre engine in a 98 Isuzu rodeo now having trouble with camshaft position sensor computer told me that's the problem I know where it goes but it's blocked off, rodeo not running perfect, what to do or can I bypass it

Jan 01, 2014 | 2003 Mini Cooper

1 Answer

2002 isuzu rodeo 2.2 liter code P0341 cmp range or performance problems


P0341 ISUZU - Camshaft Position Sensor Performance
Possible causes- Faulty Camshaft Position Sensor
- Camshaft Position Sensor harness is open or shorted
- Camshaft Position Sensor circuit poor electrical connection
- Faulty starter motor
- Starting system circuit
- Dead (Weak) battery

Sep 10, 2012 | 2002 Isuzu Rodeo

1 Answer

How do you check and change a camshaft position


The camshaft sensor wouldn't explain the clattering noise. But a timing chain would explain both. Clattering from a loose chain and the camshaft sensor code from when the chain broke and the camshafts stopped turning.

Aug 02, 2010 | 2000 Chevrolet Tracker

2 Answers

Need help finding camshaft position sensor


2.0L 2.4L Removal The camshaft position sensor is mounted to the rear of the cylinder head.

Remove the negative battery cable. Disconnect the PCV hose and reposition Disconnect electrical connectors from the camshaft position sensor. Remove camshaft position sensor mounting screws. Remove sensor.Loosen screw attaching target magnet to rear of camshaft and remove magnet.
Instalation The target magnet has locating dowels that fit into machined locating holes in the end of the camshaft.
- Install target magnet in end of camshaft. Tighten mounting screw to 3 Nm (30 in. lbs.) torque. Over torqueing could cause cracks in magnet. If magnet cracks replace it.
- Install camshaft position sensor. Tighten sensor mounting screws to 12.9 Nm (115 in. lbs.) torque.
- Carefully attach electrical connector to camshaft position sensor. Installation at an angle may damage the sensor pins. - Connect the PCV Valve hose. - Connect the negative battery cable.
2.7L V6 Removal
The camshaft position sensor is mounted in the front of the head.

Disconnect electrical connector from sensor. Remove camshaft position sensor screw.
CAM Sensor Location 2.7L
Without pulling on the connector, pull the sensor out of the chain case cover.

Installation - Install sensor in the chain case cover and push sensor in until contact is made with the boss on the head. While holding the sensor in this position,install and tighten the retaining bolt to 12 Nm (105 in. lbs.) torque.
- Attach electrical connector to sensor.

Good luck and hope this helps





May 02, 2009 | Dodge Stratus Cars & Trucks

1 Answer

Code p1340


P1340 Igniter Circuit Malfunction (No. 8)
P1340 Camshaft Position Sensor B Circuit Malfunction
It all has to do with your ignition system or misfire.
You will need a special tool to remove this item. I would recommend taking it to a mechanic and having them fix it

Feb 07, 2009 | 2000 Isuzu Rodeo

Not finding what you are looking for?
1999 Isuzu Rodeo Logo

Related Topics:

493 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

80608 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14417 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...