Question about 2002 Isuzu Rodeo

1 Answer

Nned to know how to set the cam and engine timing

Need to know how to set the cam and engine timing in a 2002 rodeo 3.2

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Guru:

    An expert who has written 7 tips or uploaded 3 video tips

  • Master
  • 642 Answers

Start with crankshaft pulley. At the rear of the pulley is a notch. Align it with the mark on the oil pump.(No 2 piston is at TDC) There is also a groove on the pulley that needs to be aligned with the white dots on the cambelt. The lettering on the belt must be readable as viewed from the front of the vehicle.
(When seated in the vehicle the RH bank of the engine is on the RH side of the vehicle.Keep this in mind)
At the front of the camshaft pulley is a groove. Rotate the RH bank camshaft pulley to align this groove with the mark on the cylinder head cover. On the cambelt is a white line. This must also align with these marks. Do the same on the LH bank. To be sure the cams are now correctly aligned remove the cylinder head cover. On the camshaft drive gears the letters RI(Right intake) and RE(Right exhaust) will be at the top and readable for the RH bank. (For the LH bank it will be LI and LE) Reinstall the tensioner and rotate the crankshaft with a wrench to make sure there is no unintentional mechanical contact.

Posted on Dec 10, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Lost timing on my 97 Isuzu Rodeo 3.2 liter single overhead cam have trouble finding marks on cam shaft idlers rockets was wondering if you had any literature or videos


idlers are not timed, just crank to cam.....
alldata.com has the timing setup for this, log in and read?
interference engines , do you know how to work them>?

im not posted all 32 steps.
but just this.
you never stated the job, just the belt bad? or cams out, or cogs off? what was fiddled so far.....???????
ill assume the cam gears are untouched.



25710444-dgpo1hlb4bclwbcfjqfhho1h-1-0.jpg
step 3 on install states
"If any binding is felt when adjusting the timing belt tension by turning the crankshaft, STOP turning the engine, because the pistons may be hitting the valves."


just 15 bucks to not bend over the head valves.
https://www.scantool.net/software/alldata-diy-1-month-subscription.html

RTM , please read the manual, then ask questions.

May 24, 2015 | 1997 Isuzu Rodeo

3 Answers

2002 Isuzu rodeo stop while driving wont start


Need more information. Could be fuel pump, fuel filter, crank sensor, cam sensor. Starter??

Oct 16, 2014 | 2002 Isuzu Rodeo

1 Answer

Isuzu Rodeo Timing Problem


Are you saying it won't crank or won't start ?
If you need the procedure to check the timing marks on the cam gears that should be in a repair book or shop manual.
It is an interference engine, so you have to be careful and not crank the engine with the starter if the cams are not in time with the crank.

Apr 03, 2013 | 2000 Isuzu Rodeo

1 Answer

I have a Isuzu rodeo 1994 3.1 in I can't find the


The timing marks are stamped into the head and in the cam pulley, also on the crank and the case, find them and paint them white so you can see them, the new belts have the marks on the belt, they will line up, If they don't , you got it wrong, You can do this without spinning the cams or crank and losing the marks, as long as the belt marks line up, you will be all set. Put the pin in the tensioner before removing the belt. Did you change the water pump? And I think the engine is 3.2L. Get it in there and pull the pin, It should be right on. Turn over the engine by hand a couple times to make sure it comes around on the marks. If it is wrong, it will go about 11 or 12 miles, and you will need a new engine. Hope this helps.

Jun 04, 2011 | 1994 Isuzu Rodeo

1 Answer

Need to know the timing marks for a 99 isuzu rodeo with the3.2 dohc


Heres two diagrams for aligning the timing gears for timing belt, this is for a 1999 rodeo with the 3.2 engine, hope this helps,one diagram is for the cams and the other is for the crank gear,d5220b7.gif813ac66.gif

May 20, 2010 | 1999 Isuzu Rodeo

1 Answer

I am replacing my timing belt and tensioners on my 1994 rodeo, when I removed the timing belt the right side cam sproket moved clock wise, I need to set the timing and do not have the steps the manuel does...


You were supposed to clamp the cams so they don't spin, not to worry, I think they will only go so far, your belt should have marks on it, If it doesn't take it back and get one with marks on it, you need these to line up with the marks on the cams and crank, if they don't line up, I'll give your engine 11 miles before that cams shatter. When all three are in line, you should be all set, pull the pin on the belt tensioner and let her rip, don't forget the water pump, you got in there, do it .

Dec 12, 2009 | 1994 Isuzu Rodeo

1 Answer

Trouble getting marks aligned on 2001 Izusu Rodeo


if its a 6VE1 engine you might want to remove rocker covers and put front lobes of camshafts in position shown in picture with cam gear timmed up at same point cam gear are 3:1 ratio


b76b855.jpglook closely at cam gears in pic to see front lobe positions for both banks

Jul 29, 2009 | 2002 Isuzu Rodeo

1 Answer

2002 Izusu Rodeo timing problems


Check with your local Izuzu dealer, there is a procedure to set the cams in proper relationship with each other. This involves turning the cams up to 8 rotations to have them "jump" into the proper spot. I have had the same problem and found a bulletin that shows the correct way to time the engine.

Dec 11, 2008 | 2002 Isuzu Rodeo

1 Answer

Cam shaft timing


Nned to know if you have a V6 or a 4 cyl.

Sep 28, 2008 | 1996 Toyota Camry

1 Answer

Timing


Yes - on the V6, the left intake cam and exhaust cam are on the same side of the vehicle. Facing the engine, the "upper" cam sprocket on that side is the intake cam, and the one that is lower and farther out toward the fender of the vehicle is the exhaust cam.

Aug 25, 2008 | 2002 Isuzu Rodeo

Not finding what you are looking for?
Cars & Trucks Logo

447 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

Marvin
Marvin

Level 3 Expert

83036 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14505 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...