Question about 2002 Chevrolet Silverado 1500HD

1 Answer

2005 Chevrolet Silverado 1500HD 4 wheel drive front wheel hub replacement. Need to know what torque to put on front axle nut that attachs to front hub

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Chevrolet Master
  • 599 Answers

177 ft lbs

Posted on Dec 09, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace a hub in a 2005 Buick Terraza


remove tire/wheel. remove brake caliper/ bracket. remove center axle nut. remove 4-hub nuts. hub should come out with hands. Grease and red-torque all appropriate parts during reassembly.

Mar 18, 2016 | 2005 Buick Terraza

1 Answer

What are the torque specs for a front axle bearing/hub?


Not sure about your model, but in general they are usually around 180 ft./lbs.

Aug 01, 2014 | 2003 Chevrolet Silverado 1500

1 Answer

Torque specs axle nut


Wheel nut torque 140 lb ft

Dec 31, 2013 | Cars & Trucks

1 Answer

How do I rgerplabe how do I replace a front wheel bearing?


TO REMOVE FRONT WHEEL BEARING.YOU NEED TO SAFELY RAISE SUPPORT VECHICLE ON JACK STANDS.MAKE SURE SITTING ON LEVEL SOLID GROUND.BEFORE RAISING VECHICLE OFF GROUND YOU NEED TO LOOSEN HALF SHAFT AXLE NUT JUST A LITTLE BECAUSE WHEEL IN THE AIR HARD TO LOOSEN AXLE NUT WHEN YOU HAVE HOLD THE WHEEL WHILE LOOSEN THE AXLE NUT WHICH IS TORQUE ON ABOUT 200 FT LBS.USING A SIX POINT AXLE SOCKET SOCKET SIZE COULD BE 34 OR 35 METRIC 1/2 INCH SOCKET.YOU NEED 1/2 INCH BREAKER BAR.ONCE YOU LOOSEN AXLE NUT A LITTLE THEN RAISE VECHICLE THEN REMOVE WHEEL.THEN FINISHING REMOVING AXLE NUT AND WASHER.THEN REMOVE THE CALIPER FROM THE STEERING KNUCKLE AND SUPPORT IT ASIDE USING A PIECE OF WIRE.REMOVE BRAKE ROTOR.THEN REMOVE THE 3 HUB BEARING ASSEMBLY BOLTS. USE A SWIVEL SOCKET GOING TO BE HARD TO REACH SPOT WITH A REGULAR SOCKET. REMOVE THE HALF SHAFT FROM THE HUB BEARING ASSEMBLY.REMOVE HUB AND BEARING ASSEMBLY. PUT EVERY THING BACK VISA VERSA. TORQUE HUB BEARING BOLTS TO 70 FT LBS. TORQUE AXLE NUT 284 FT LBS IF YOUR CAR IS 1998 MODEL AND TORQUE AXLE NUT 100 FT LBS FOR THE 1999 TO 2001 MODELS.THE WHEEL HAS TO BE ON THE GROUND JUST ENOUGH TO KEEP IT FROM TURNING.DONT LET ALL THE CAR WEIGHT DOWN UNTIL YOU HAVE TORQUE WHEEL TO THE RIGHT TORQUE.LET ME KNOW IF YOU HAVE ANY PROBLEMS.

Mar 21, 2011 | 1999 Oldsmobile Alero

2 Answers

How do I replace the front wheel bearings on a


remove cv outer nut, tire brake caliper and lower ball joint use a bar to pry against lower a frame to seperate ball joint slip out cv axel then remove four nuts securing wheel bearing. I would have to check at home for exact instructions.

May 18, 2010 | 2005 Chevrolet Silverado

2 Answers

Noise coming from front brakes or wheel ,i change brake pads


Did you have the rotors turned? Did you check for rotor runout? Did you remove all rust from hub face and rotor mounting surface? Did you remove rust from caliper or pad slides? Lube all caliper and pad sliding surfaces? Are the pads application specific? Did you flush and bleed the fluid? Did you torque the wheels properly?

Feb 09, 2010 | 2005 Chevrolet Silverado 1500HD

1 Answer

Replacing front hub on a 2001 Chevy Silverado 1/2 ton 4 x 4. need to know torque for retaining nut


The torque for the front drive shaft and hub retaining nut is 155ft.lbs. But if you are on the metric system,
it's 210N.m . These specs are for both 1999 and 2001
Hope this helps. Good luck.

Jan 24, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

Front wheel berings 2003 silverrado 1500 4 wheel drive describe procedure to change out


reomve tire securing the vehicle with tire hanging at it's lowest possition, remove the brake caliper & brake disc , remove nut lock on axle also axle nut , mark and remove strut bolts and push strut out remove ball joint lower bolt and use a fork ( tooling) seperate from hub slide hub off of axle , reverse steps to replace .

Aug 22, 2009 | 2003 Chevrolet Silverado 2500HD

2 Answers

Front Hub Bearing Torque specs to complete replacement


THE LUG NUT TORQUE SPEC - 140FT/LBS\
CALIPER MOUNT - 80FT/LBS
CALIPER BRACKET 129FT/LBS
AXLE NUT 177FT/LBS

Apr 24, 2009 | 2003 Chevrolet Silverado 1500

Not finding what you are looking for?
Cars & Trucks Logo

669 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

Marvin
Marvin

Level 3 Expert

83096 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...