Question about 1995 Volkswagen Golf

1 Answer

Bent lower control arm and tie rod front passenger side? I need to remove the damaged ones and replace them.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 447 Answers

Not that difficult if you are mechanically inclined. You WILL need a front end alignment as soon as you replace them. Use jack stands!!

Posted on Dec 25, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I have a 2010 Ranger 4x4 one front wheel campher and toe in are considerable off. What do I adjust to correct?


the camber is set on these by the bushings (offset) in the spindle platform and the bushing at anchor point near other side of arm , generally its not repairable its replaceable ! the toe is set by the screw adjustments ball joints attached to rack and pinion steering module , also are you sure its not the wheel bent, use the spare tire to ck adjustments or move a back wheel up front and test it again

Aug 12, 2016 | Cars & Trucks

2 Answers

Front driver side leaning inward, have changed strut,etc...


Upper and lower ball joints. Control arm bushings bad. or both.

Jul 09, 2016 | Cars & Trucks

1 Answer

My 2000 Concord is still making a bang from passenger front Just changed half shaft , rotor , caliper and pads Is it the ball joints ? Bangs when i stop


jack up and support vehicle grab top and bottom of wheel and see if its loose if loose feeling up top or clunking possible upper ball joint if bottom feel/noise poss bottom ----move wheel side to side and look and check tie rods if loose or noise inspect and replace if damaged or worn ---remove wheel and inspect the joints and tie rods if their was no noise or worn check the upper and lower control arm bushings as well as the swaybar supports and bushings

May 18, 2016 | Cars & Trucks

1 Answer

Need a diagram of front end have to change lower control arm pin and bushing and front struts


if you only replace one side,you will not be able to correct tow,do both sides,upper and lower and tie rod ends and all bushings,ebay has kits

Jul 23, 2015 | 2001 Mazda Tribute

1 Answer

Have replaced all tie rods; inner&outer;struts&upper mounts;sway bar bushings & links;lower control arms with ball joints& passenger side upper motor mount.none of these have changed this noise even s


What noise? And year and make of car?
A clicking noise on turns is a worn CV joint on the axle shafts. A grinding noise at one of the wheels could be a wheel bearing. Worn brake pads may cause squealing, screeching other high pitched noise.

Jul 25, 2013 | Cars & Trucks

2 Answers

I want to know how to fix the alignment on my 1995 honda accord ex.


Before making wheel alignment adjustment, perform the following checks:
  1. Tires should be equal in size and runout must not be excessive. Tires and wheels should be in balance, and inflated to manufacturer's specifications.

  2. Wheel bearings must be properly adjusted. Steering linkage and suspension must not have excessive looseness. Check for wear in tie rod ends and ball joints.
  3. Steering gear box must not have excessive play. Check and adjust to manufacturer's specifications.
  4. Vehicle must be at curb height with full fuel load and spare tire in vehicle. No extra load should be on vehicle.
  5. Vehicle must be level with floor and with suspension settled. Jounce front and rear of vehicle several times and allow it to settle to normal curb height.
  6. If steering wheel is not centered with front wheels in straight-ahead position, correct by shortening one tie rod adjusting sleeve and lengthening opposite sleeve equal amounts.
  7. Ensure wheel lug nuts are tightened to torque specifications
Ride Height Adjustment

Before adjusting alignment, check riding height. Riding height must be checked with vehicle on level floor and tires properly inflated. Passenger and luggage compartments must be unloaded. Bounce vehicle several times, and allow suspension to settle. Visually inspect vehicle from front to rear and from side to side for signs of abnormal height.
Measure riding height. See figure. Riding height between left and right sides of vehicle should vary less than 1′ (25.4 mm). If riding height is not within specification, check suspension components and repair or replace them as necessary.
Wheel Alignment Procedures

Honda recommends using commercially available computerized 4-wheel alignment equipment. Follow equipment manufacturer instructions to obtain vehicle alignment settings. Use following procedures for necessary adjustments.
Civic Camber Adjustment
Compare camber settings with vehicle manufacturer recommendations. If camber is incorrect, check for bent or damaged front suspension components. Replace faulty components. Recheck camber.
Civic Caster Adjustment
DO NOT use more than 2 shims. If more than 2 shims are required to adjust caster angle, check for bent or damaged suspension components.
Compare caster settings with vehicle manufacturer recommendations. If caster is incorrect, check for bent or damaged front suspension components. Replace faulty components. Recheck caster.
Civic Toe-In Adjustment

  1. Secure steering wheel in straight-ahead position. Measure front wheel toe-in. If adjustment is needed, loosen tie rod lock nuts. Turn both tie rods equally in the same direction until front wheels are in straight-ahead position and toe-in reading is correct. Tighten tie rod lock nuts. Reposition tie rod boots if twisted.
  2. Ensure parking brake is released. Check rear wheel toe-in. If adjustment is needed, hold adjusting bolt on rear compensator arm and loosen lock nut. See figure. Adjust rear toe-in by sliding rear control arm until rear toe-in is correct. Install NEW lock nut, and tighten it while holding adjusting bolt.
Wheel Alignment Specifications

  • Camber - Measurement in degrees.
    • Front: 0 (range -1 to 1)
    • Rear: 0.33 (range -1.33 to 0.67)
  • Caster - Measurement in degrees.
    • 1.17 (range 0.17 to 2.17)
  • Toe-In - Measurement in inches (mm).
    • Front: -0 (0)
    • Rear: 0.08 (2.0)
  • Toe-In - Measurement in degrees.
    • Front: 0.00 (range - 0.16 to 0.16)
  • Toe-Out On Turns - Measurement in degrees.
    • Inner: 41.00
    • Outer: 33.50
Torque Specifications Ft. Lbs (N.m)

  • Rear Control Arm Adjusting Bolt: 48 (65)
  • Spindle Nut: 136 (185)
  • Tie Rod Lock Nut: 41 (55)
  • Wheel Lug Nuts: 80 (108)
hope this helps you out.

May 09, 2011 | 1995 Honda Accord

1 Answer

Front lower control arm replacement


To remove the lower control arm raise and support your car with jack stands.Next you want to remove the wheel that you are replacing the control arm on.Remove the ball joint nut and tie rod nut.Tap the steering knuckle to break the tie rod end loose from the knuckle DO NOT HIT THE TIE ROD SO HARD YOU DAMAGE THE THREADS.If you do you will also be changing a tie rod end.Tap on the steering knuckle until your ball joint stud comes loose.Remove the 2 bolts that mount the control arm to the frame.To install the new one just go in reverse.

Mar 09, 2011 | 2006 Ford Mustang

1 Answer

How to replace the passenger control arm on the 2006 suzuki grand vitara


Most front ends are set up basically the same way.First raise and support your front end and remove the tire.Both the upper and lower should look about the same.If you look at the control arm you will have an upper and lower ball joint and a tie rod end bolted to the steering knuckle.Remove the bolt on the tie rod end and use a ball joint separate to remove the tie rod end.Then remove the ball joint from the steering knuckle with your separator.Depending on which control arm it is if its the upper you will also have to remove the brake hose out of the way to remove the upper control arm.Once that's done you will see 2 bolts that hold the control arms to the frame remove these bolts and your control arm will come off,You might have to pry them a little bit to get them out.You also want to have something handy to block up your steering knuckle until your ready to put it back together.It wouldn't hurt to have a piece of wire just in case you need to tie something in place.And be sure you grease everything with a high pressure grease.

Mar 06, 2011 | 2006 Suzuki Grand Vitara

1 Answer

How to replace right front axle 2000 buick lesabre


Lift the passenger side of vehicle. Remove tire/wheel assembly. Remove the axle nut. Remove the tie rod end nut. Smack the side of the housing the tie rod end goes into to pop the tie rod end loose and out. Remove the sway bar link. Remove the lower ball joint nut. Smack the housing the lower ball joint goes into to pop the ball joint loose. Pry the lower control arm down to pop the ball joint out. swivel the rotor and strut assembly to the side. Pop the axle out. Reassemble in the reverse order.

Jul 05, 2009 | 2000 Buick LeSabre

1 Answer

Need to replace steering arm on pass side on 1998


Your description leads me to believe that the spindle is bent. This is the piece that the tie rod attaches to near the wheel. Sometimes the tie rod is attached to a piece that attaches to the spindle which is rather intuitive. Just remove the tie rod end, unbolt the arm that attaches to the spindle and replace the arm. In this case the only special tool you'll need is a tie rod seperator.

If the arm is a part of the spindle and cannot be removed easily:

1) Put vehicle in park and safety brake on - chock the rear wheels
2) Lift passenger side front wheel and put on jack stands
3) Remove wheel and have a friend apply brake pressure
4) Loosen hub nut with appropriate socket (22 to 35mm)
You can purchase the socket from your local auto parts store
You'll need a large breaker bar, its torqued to about 100ft-lbs
5) Remove tie rod end with a tie rod/ball joint separator
This can also be purchased at your local auto parts store.
Some spindles are made with tie rod end permanantly attached
If it is removable, remove nut and drive the separator tool
between the tie rod and spindle using a large hammer.
It'll eventually break free from the spindle.
6) Remove the strut with a strut spring compressor tool
WARNING - THIS IS VERY DANGEROUS
This can be purchased at your local auto parts store.
Compress spring before removing lower bolts (2 of them).
The strut may be left on vehicle but the spring must be
compressed.
7) Remove caliper and break assembly
Loosen the two slide bolts that go through the caliper assembly
Remove caliper and breaks - let it hang by the tubing
8) Detach upper and lower ball joints with seperator tool as in #5
9) Finally remove the hub nut from #4
The spindle should slide off the axle
10) Repair or replace the spindle and put it all back together in
reverse order using new wheel bearings. Pack them with axle
grease if theyr'e not the sealed type.

NOTE: The tie rod end may need to be replaced also. The vehicle will need a front end allignment. Be sure to torque the hub nut to the manufacturers specifications - at least 75ft-lbs. You should probably replace the wheel bearings.

Jan 02, 2009 | 1998 Chevrolet Malibu

Not finding what you are looking for?
1995 Volkswagen Golf Logo

Related Topics:

214 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Marvin
Marvin

Level 3 Expert

81285 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8841 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...