Question about 1998 Dodge Durango

1 Answer

ObdII reader wont connect to my 98 dodge durango 5.2 is there any other ways to check the codes?

Posted by on

  • jerbear2143 Dec 09, 2009

    i turned it on then off and the third time of turning it on left it on and the odometer didnt show any codes just the milage.

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 4 Answers

Yes , you never need a scanner with any dodge products. Just put the key in the ignition. Turn the key on and off three time ..leave it on the on position and watch the odometer. it will say the code.

Posted on Dec 09, 2009

Testimonial: "very fast response easy to use info nd site"

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 1998 dodge durango slt wont drive past 40 miles an hour


Hello Jeff Winner,

Over the last 20 years ... cars have has a LIMITED OPERATION FEATURE added... When the engine READS something that is not IMMEDIATELY catastrophic... it will allow you to
LIMP home... rather than a complete shut down.

Limp mode:
You SHOULD also have a CHECK ENGINE light... (?)

My best advice is to limp on down to your near-by FREE code reading shop... and have a READER tell you what CODES are registered...

A blocked exhaust system will also seriously SLOW your progress
((soon to stop all-together)).

Hope this helps

Check you exhaust prices BEFORE you go...!!

http://www.rockauto.com/en/catalog/dodge,1998,durango,5.9l+v8,1314473,exhaust 1998 DODGE DURANGO 5 9L V8 Catalytic Converter RockAuto

1998 DODGE DURANGO 5 9L V8 Muffler RockAuto

Nov 27, 2016 | 1998 Dodge Durango

1 Answer

I have a 98 dodge durango 5.2 and I took the glow gauges of of it when I bought it n when I put the temp needle back on it stopped working...how do I get it working again?


98 Dodge Durango Starting Problem - CarGurus

www.cargurus.com > Questions > Dodge > Durango
CarGurusJun 16, 2010 - 98 Dodge Durango Starting Problem - Alrighty guys , I need some help. ... Have 98 5.2 had some of same problems---first clean connections

Jul 20, 2015 | Dodge Cars & Trucks

1 Answer

98 firebird 3.8 will not start checked the problems with teh computer and it gave me PO743


Here is the OBDII code reader manual:
http://ossh.com/dodge/mods%20and%20tricks/OBDII%20code%20reader%20owners%20manual.pdf

The code P0743 is
P0743 Torque Converter Clutch Circuit Electrical This is usually the clitch solenoid being shorted or open.

If memory servs me right it will have blue and gray wires on it.in the top left area. Just not sure at the moment.

Thanks for choosing FixYa,
Kelly

Jul 17, 2011 | 1998 Pontiac Firebird

2 Answers

I replaced the egr sensor and still have a p0406 engine light error.


you have to use scan tool to clear obdII codes.

Murrays oriely

Mar 29, 2010 | 2005 Dodge Durango

3 Answers

My engine light on my 2006 dodge durango just turned on and i just got this vehical 5 months ago.


Run diagnostics on it to see what it is.Just because it is new or newer does not mean there could be no fault!

Mar 18, 2010 | 2006 Dodge Durango

1 Answer

Oil pressure gauge goes down when i make a stop and goes back up when i take off. after a while the emission light appears on console


Check the oil sending unit.

Is it a leaker?

Also check the wire from the oil sending unit.

It can be ground to the frame or motor.

Use nylon tie to make sure it's secure and the wire insulation is in good shape.

======

You can get an OBDII code reader and get the code easily,

Get the PXXXX code(s) and post it on the comment window.

I will follow up later.

Dec 11, 2009 | 2001 Dodge Durango

1 Answer

1998 Toyota Avalon Check engine light


should have an OBDII connection under the dash on the drivers side. Looks like an elongated computer port, probably has a cover on it that says OBDII. You can buy a code reader from an auto store like pepboys for around $100 i think. Just a side note, usually if the car is still driving ok and not acting weird, it is an emissions sensor.

Jun 22, 2009 | 1998 Toyota Avalon

2 Answers

2000 DURANGO 5.9


I recommend that you go to your local AutoZone they have a code reader and they don't charge for it.

There is a way to make the car tell you, but it's safer to hook it up and read it that way.

Jul 27, 2008 | 2000 Dodge Durango

Not finding what you are looking for?
1998 Dodge Durango Logo

Related Topics:

660 people viewed this question

Ask a Question

Usually answered in minutes!

Top Dodge Experts

Marvin
Marvin

Level 3 Expert

83081 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Dodge Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...