Question about 2005 Pontiac Grand Prix

1 Answer

My remote start is disabled. It was working okay. I put the key in the ignition while the remote start was on and the DIC message showed, "Remote Disabled," and now the remote start does not work.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,533 Answers

You may have to take it back to the place that install it for you they be able to reset the codes in it and you be good to go wish you the best of luck Michigan Man.

Posted on Dec 09, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How does the ignition interlock work on the mazda mpv 2003 ? I can't start the car without the remote control : Simply turning the key will not even crank, does nothing.


Often, you need to press the unlock button on the remote twice. First press unlocks the door and second press disables the immobiliser and allows the vehicle to start. The key alone will not start the vehicle.

Alternatively, when the key is in the ignition - press the remote unlock again.

The remote acts as an immobiliser device. The reason your car won't start on the key is probably because the system won't allow any key in the ignition - it is preventing theft of the vehicle. Once the unlock button on the remote is pressed the system then recognises that key is the legitimate one for the vehicle and the disables the immobiliser and allows you to start the car

Feb 19, 2016 | Mazda Cars & Trucks

1 Answer

After completing the 45 minute relearn procedure for a 2004 Pontiac Grand Prix message center Now says system not programmed


Relearn for what ? Anti theft system PK3 ? The relearn procedure is three 10 min. procedures for a total of 30 min.
30-Minute Relearn Procedure
Use this procedure after replacing the following components:
?€¢
The passkey III (PK3) keys


?€¢
The BCM


?€¢
The PCM, see important above

Important: This procedure is not available on vehicles equipped with option code (Z49).
If replacing a BCM with an GM SPO Replacement Part, perform the procedure to setup a new BCM prior to the 30-minute relearn procedure.

  1. With a master passkey III key, turn ON the ignition, with the engine OFF.
  2. Observe the STARTING DISABLED DUE TO THEFT message on the drivers information center (DIC), after approximately 10 minutes the STARTING DISABLED DUE TO THEFT message on the DIC will turn off.
  3. Turn OFF the ignition, and wait 5 seconds.
  4. Repeat steps 1-3 two more times for a total of 3 cycles or 30 minutes.
  5. Important: The vehicle learns the key transponder information and/or passwords on the ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle.
  6. With a master passkey III key, start the vehicle. The vehicle has now learned the key transponder information and the PCM has now learned the fuel continue password.
  7. With a scan tool, clear any DTCs.

Dec 07, 2015 | Pontiac Cars & Trucks

1 Answer

2004 Pontiac Grand Prix pk3 relearn procedure does the starter to disable due to theft system to turn to turn off before going to step 2off before going to the second 15 minutes with Ken secL


Your doing it wrong !
30-Minute Relearn Procedure
Use this procedure after replacing the following components:
?€¢
The passkey III (PK3) keys


?€¢
The BCM


?€¢
The PCM, see important above

Important: This procedure is not available on vehicles equipped with option code (Z49).
If replacing a BCM with an GM SPO Replacement Part, perform the procedure to setup a new BCM prior to the 30-minute relearn procedure.

  1. With a master passkey III key, turn ON the ignition, with the engine OFF.
  2. Observe the STARTING DISABLED DUE TO THEFT message on the drivers information center (DIC), after approximately 10 minutes the STARTING DISABLED DUE TO THEFT message on the DIC will turn off.
  3. Turn OFF the ignition, and wait 5 seconds.
  4. Repeat steps 1-3 two more times for a total of 3 cycles or 30 minutes.
  5. Important: The vehicle learns the key transponder information and/or passwords on the ignition switch transition from OFF to CRANK. You must turn the ignition OFF before attempting to start the vehicle.
  6. With a master passkey III key, start the vehicle. The vehicle has now learned the key transponder information and the PCM has now learned the fuel continue password.
  7. With a scan tool, clear any DTCs.

Dec 07, 2015 | Pontiac Cars & Trucks

1 Answer

I have a 2006 Chevrolet Malibu and the keyless entry started working intermitantly and now randomly works maybe once a week. It wont pop the trunk or lock or unlock the doors. I replaced the batteries in...


Unfortunately you may not have a choice in the matter ! You have no idea of the electronics involved here . No one knows your GM vehicle better . And $ 85 dollars is a heck of alot better then $115.00 dollars a flat rate hour . Pep boy's , firestone , AAMCO .
The keyless entry system has the following main components:
• The transmitters
• The body control module (BCM)
• The remote control door lock receiver (RCDLR)--When you press a button on the transmitter, the transmitter sends a signal to the RCDLR. The RCDLR receives the signal and sends a X Link serial data message requesting the appropriate function from the BCM.

Customer Programming Method for Enabling/Disabling the RVS Feature
Using the driver information center (DIC), the RVS feature can be DISABLED and ENABLED just like other items programmable via the DIC. When a lock control, entry-remote entry, extended range (AP8) equipped vehicle has RVS added to it and the vehicle is not DIC equipped and the customer wants to disable RVS. The dealer will perform the DISABLED remote start function since the owner cannot perform the function on thier own without a DIC.

Important: All transmitters that are to be recognized by the remote control door lock receiver (RCDLR) must be programmed in a single programming sequence. If the system is placed in program mode, all previously programmed transmitters will be erased upon receipt of the programming signal from the first transmitter.
Up to 4 transmitters can be programmed. Do not operate or program the transmitters in the vicinity of other vehicles that are in the keyless entry program mode. This prevents the programming of the transmitters to the incorrect vehicle. The order in which the transmitters are programmed is important. The first transmitter programmed will be transmitter #1, and the second transmitter programmed will be transmitter #2. Use care to program the transmitters correctly.
The scan tool must stay connected until all of the transmitters are programmed. All doors must be closed to perform this function.
Install CANDI module.
Install a scan tool.
Turn ON the ignition with the engine OFF.
With the scan tool, select Vehicle Control Systems.
Select Computer/Integrating Systems.
Select the proper engine size.
Select Module Setup.
Select Body Control Module (BCM).
Select Program Key Fobs.
Follow scan tool on screen instructions.
Remove the scan tool.
Exit the vehicle. Attempt to lock/unlock the doors to verify the programming.
Operate the transmitter functions in order to verify correct system operation.

May 04, 2017 | 2006 Chevrolet Malibu

1 Answer

If I unlock car with key, horn blows. If I start vehicle, it starts okay but shuts off immediately afterward. I tried unlocking manually, then relocking manually. Batteries are NEW in remote and Reily's...


did you try doing that with other door?if not i would try then unlock doors then if horn don't blow put key in and cycle 3 times then turn off wait a few then start you may also find a reset procedure in the owner manual hope this works 4U if it dos please share it with us thank you

Mar 12, 2010 | Dodge Durango Cars & Trucks

2 Answers

My alarm wont turn off. my car wont start. its a 2004 tiburon.


With alarm activated your ignition is disabled.Find the combination to disable it.With GM's you hold opposing buttons on the fob till it beeps twice. The dealer should help for no charge.

Feb 28, 2010 | 2004 Hyundai Tiburon

1 Answer

Purchased a new clicker.from g/m.i can't program it.i have replaced the transformer under the dash panel that was used.. i have been told 96 models has several transmitters on it.


1. Move all Keyless Remotes out of range of vehicle. (10 to 15 feet)
2. Turn ignition key to the ON position.
3. Push the TRIP/ODO button on the DIC (Driver Info Center) twice.
4. Within 5 seconds, push & hold the FUEL INFO button on the DIC until
the PKE light comes on and stays on.
5. Turn the ignition to the OFF position, but leave the key in the ignition.
The PKE light will begin flashing.
6. Bring one Keyless Remote into range. The PKE light will stop flashing
and stay on to show the code is stored. Move the Keyless Remote out
of range. The PKE light will begin flashing indicating the system is ready
for the next Keyless Remote.
7. If more than one Keyless Remote is being programmed, move the first
Keyless Remote out of range and repeat step 6 for any additional Keyless
Remotes. Up to three Keyless Remotes can be programmed.
8. To turn off the programming mode, simply remove the key from the ignition
or turn the ignition switch on.
9. The programming mode will shut off after two minutes if.
A) You have not programmed any Keyless Remotes.
B) Removed the key from the ignition.
C) After three Keyless Remotes have been programmed.

Good luck and keep me posted.

Jan 23, 2010 | 1996 Chevrolet Corvette

1 Answer

Programming a keyless entry remote


Key Fob Auto Learn
This procedure will first erase all known key fobs. The procedure will then program a single or multiple key fobs. Method 3 is a series of three 10-minute key cycles, for a total of 30 minutes. This procedure requires that you have a replacement key fob and the vehicle mechanical key.

Important: All previously programmed key fobs will be erased upon completion of the 30-minute programming procedure. The order in which the key fobs are programmed will determine its numbering position within the RCDLR memory. The first key fob programmed will be key fob #1, and the second key fob programmed will be key fob #2. The number stamped on the key fob case is for reference only: #2 can be programmed as #1.
Do not place any known good key fobs in the vicinity of the vehicle when programming. 

The vehicle must be OFF. 
Place the replacement key fob in the console pocket with the buttons facing forward. 
Insert the vehicle key in the driver door lock cylinder located in the driver door handle and cycle the key 5 times within 5 seconds. 

The DIC will display a message: OFF/ACC TO LEARN. 
Press the OFF/ACC portion of the ignition button. 
The DIC will display a message: WAIT 10 MINUTES, then it will count down from 10 to 0, one minute at a time. 
When the counter reaches 0, DIC will display OFF/ACC TO LEARN. 
Repeat steps 5-7 two more times, for a total of 30 minutes. 
The DIC will display a message: OFF/ACC TO LEARN. 
Press the OFF/ACC portion of the ignition button. 
A beep will occur and the DIC will display: READY FOR FOB 1. At this time all previously known key fobs have been erased. When fob 1 is programmed a beep will be heard and the DIC will display a message: READY FOR FOB 2. 
Additional key fobs can be programmed by taking fob 1 out of the pocket and inserting fob 2. If desired, up to 4 fobs can be programmed. Once 4 fobs have been learned, the DIC will display a message: MAX FOBS LEARNED, and automatically exit the program mode. 
If learning less than 4 key fobs, press the OFF/ACC portion of the ignition button to exit the program mode. 
Operate the active portion of each key fob in order to finalize the programming sequence and verify correct system operation. 

Good luck and hope this help's keep me posted, there are 3 other methods and the 5th method is a tech 2 scan tool that the dealer uses but this should work on your year of cadillac. 

Jul 01, 2009 | 2003 Cadillac Deville

2 Answers

I have a 2006 G6 and the remote starter recently stopped working. The remote will lock and unlock the doors but when I hit the lock and then starter button on the remote the lights will just flash and you...


you can only start the car starter three time before pcm disables the function must start agin with key to get working. also may have diabled car starter by dic comands on radio also if you have engine light on will not operate car starter due to light.

Jan 02, 2009 | 2005 Pontiac G6

1 Answer

REMOTE START OPTION MISSING FROM DIC


they problably put a bcm in without the remote start or you might have to set the parking brake like in standard cars.

Dec 04, 2008 | 2005 Pontiac Grand Prix

Not finding what you are looking for?
2005 Pontiac Grand Prix Logo

572 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

78936 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8836 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...