Question about 1992 Daihatsu Charade

1 Answer

Overheating in Diahatsu Charade 92. EFI 16 Valve.

Overheating new water pump, timing belt,new thermostat.New headgasket, Inlet and outlet gasket.Still overheats in 10 mins.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,586 Answers

Did you burp the coolant? If not, you have air bubbles in the system that are trapped behind the thermostat, keeping it from opening. Run the car at idle until it's 3/4 of the way to overheating, then shut it down and let it cool. Pop the radiator cap and the air bubbles will burp out. Check the level of coolant in the radiator and expansion tank, top off as needed, and repeat a couple times, and you should be good to go.

Posted on Dec 09, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Overheating problem


overheating sound like faulty thermostat.thermostat either sticking close or could have blown headgasket if you see a lot of white smoke coming out of exhaust.if headgasket is leaking check engine oil should look milky.also check water pump look around weep hole or see coolant leaking around water pump replace water pump.also check water pump drive belt.make sure drive belt not loose slipping.

Mar 26, 2013 | 1991 Plymouth Sundance

1 Answer

Help! I'm stuck and stumped. 2001 Beetle GLS 2.0 - Two weeks ago the car was overheating quickly, red temperature light flashing and beeping. I changed the thermostat, flushed the radiator and filled it...


SOUND LIKE COOLANT FANS HAS A FAULTY THERMO SWITCH LOCATED AT THE BOTTOM OF THE RADIATOR ON LEFT HAND SIDE.CHECK THE FUSES 8 IN THE ENGINE COMPARTMENT AND CHECK FUSE 16 IN THE PASSENGER COMPARTMENT FUSE BOX.WHEN ENGINE OVERHEATING IF BOTH COOLING FANS WORKING.OVERHEATING PROBLEM COULD BE BLOWN HEAD GASKET.CHECK ENGINE OIL LOOKS LIKE MILK HEAD GASKET LEAKING.SEE WHEN YOU DRIVING LOW AND HIGH SPEEDS THE COOLING FANS SUPPOSE TO BE RUNNING.IF THEY NOT RUNNING THAT IS YOUR OVER HEATING PROBLEM.

Feb 02, 2011 | 2001 Volkswagen Beetle

1 Answer

Where is the thermostat on a 2002 sable?


Try this:




3.0L DOHC Engine





  1. Drain the coolant until the level of the coolant is below the level of the thermostat.
  2. Raise the vehicle and support it with jackstands.
  3. Disconnect the lower radiator hose from the water inlet connection.
  4. Unfasten the two water inlet connection retaining bolts and remove the water inlet connection.
  5. Remove the O-ring seal and thermostat from the water inlet connection. Inspect the O-ring for damage and replace as necessary.

To install:
  1. Clean the water inlet connection mating surfaces.
  2. Install the O-ring, thermostat and the water inlet connection. Refer to the accompanying illustration If you can-t remember how the O-ring and thermostat are positioned.
  3. Install the water inlet connection assembly retainers and tighten them to 71-106 inch lbs. (8-12 Nm).
  4. Connect the lower radiator hose to the water inlet connection.
  5. Fill the engine with coolant, start the engine and check for leaks.
  6. Stop the engine and top off the coolant recovery reservoir as necessary.

    0996b43f80233418.jpg

    Fig. Exploded view of the water inlet connection and the thermostat assembly-3.0L DOHC engines



3.0L OHV Engine




  1. Drain the coolant until the level of the coolant is below the level of the thermostat.
  2. Disconnect the upper radiator hose from the water hose connection.
  3. Unfasten the three water inlet connection retaining bolts and remove the water hose connection.
  4. Remove the gasket and thermostat from the water hose connection. Discard the gasket.

To install:
  1. Clean the water inlet connection mating surfaces.
    NOTE The jiggle valve on the thermostat must be in the up position.
  2. Place the thermostat in the water hose connection making sure the thermostat jiggle valve is facing up.
  3. Install the new gasket and place the water hose connection assembly into position.
  4. Install the water hose connection assembly retainers and tighten them to 89-124 inch lbs. (10-14 Nm).
  5. Connect the upper radiator hose to the water hose connection.
  6. Fill the engine with coolant, start the engine and check for leaks.
  7. Stop the engine and top off the coolant recovery reservoir as necessary.

    0996b43f80233417.jpg

    Fig. Exploded view of the water hose connection and the thermostat assembly-3.0L OHV engines


    0996b43f80233468.jpg

    Fig. Remove the upper radiator hose from the water outlet


    0996b43f80233469.jpg

    Fig. Remove the water outlet retaining bolts and . . .


    0996b43f8023346a.jpg

    Fig. . . . remove the outlet from the engine


    0996b43f8023346b.jpg

    Fig. Remove the thermostat from the water outlet


    Fig. Inspect the water outlet connection for cracks or damage


    0996b43f8023346d.jpg

    Fig. Thoroughly clean the mating surfaces of the water outlet and . . .


    0996b43f8023346e.jpg

    Fig. . . . the engine before installing a new gasket


    0996b43f8023346c.jpg

    Fig. The jiggle valve must be in the up (12 o-clock) position after installation into the water outlet

Jan 19, 2011 | 2001 Mercury Sable

1 Answer

1997 diahatsu charade ltd overheating no water leaks ,no water in oil, hopefully could be thermostat, were is thermostat located?


open the car hood. look at the radiator, and then the top radiator hose. follow that hose to the engine. the hose connects to the thermostat housing cap. under that cap is the thermostat. here's what you need: ratchet, and sockets, flat-tip screwdriver, scraper, pliers, a new thermostat (any auto parts store), a new gasket, and some gasket sealant. Question, how old are hoses? if 3 years or old, let change those also. 2 new hose, 4 hose clamps, and some coolant. If we're changing hoses with this, lets start. drain the radiator, and remove the hard hose first, the bottom. now remove the top.hose, and lets start the thermostat. remove the bolts holding down the cap, and gently pry off the cap. flip the cap over, and scrape it clean to metal(we want NO leaks). now reach down and remove the thermostat, and lets scrape the housing clean to metal. place the new thermostat in the housing, and lets put a thin coat of gasket sealant on the housing. place the gasket on the sealant, and pick up the cap. apply a little gasket to the cap. place on top of the gasket, and bolt it down. now hook the hoses(if your changing them)and let sit 30 minutes for the gasket sealant set. after that, let add the coolant, and water. start the car, let it warm up. when the new thermostat opens, add more coolant as need to top it off. Hope this helps

Jan 03, 2011 | Daihatsu Charade Cars & Trucks

1 Answer

Where is the water pump gasket or the thermostat gasket in a 2002 cadillac escalade?


Thermostat Removal & Installation 4.8L, 5.3L and 6.0L Engines To Remove:
CAUTION
The thermostat is not serviceable separately. The thermostat housing (water pump inlet) and thermostat must be replaced as an assembly.
  1. Remove the radiator outlet hose. chevy_aval15_02-04_inlet.gif

  2. Remove the bolts from water pump inlet.
  3. Remove the water pump inlet from the water pump.
To Install:
  1. Install the water pump inlet to the water pump.
  2. Install the water pump inlet bolts. Torque to: 11 ft-lbs. (15 Nm)
  3. Install the radiator outlet hose.
8.1L Engines To Remove:
  1. Before servicing the vehicle refer to the precautions at the beginning of this section.
  2. Drain the cooling system.
  3. Remove or disconnect the following:
    • Inlet hose from the water outlet Water outlet and thermostat removal chevy_sub25_02-04_60_thermost_rem.gif

    • Water outlet bolts (B)
    • Water outlet (A)
    • Thermostat (C)
To Install:
  1. Install or connect the following:
    • Thermostat
    • Water outlet
    • Water outlet bolts and tighten the bolts, Torque to: 22 ft-lbs (30 Nm)
    • Inlet hose to the water outlet
  2. Fill the cooling system.
  3. Test drive the vehicle to confirm the repairs.
prev.gif next.gif

Nov 09, 2010 | Cadillac Escalade Cars & Trucks

1 Answer

How do I change a water pump on a 2004 kia sorento?


Kia Sorento 2003-05
Water Pump - Removal & Installation
  1. Before servicing the vehicle, refer to the precautions at the beginning of this section.
  2. Drain the cooling system.
  3. Disconnect the negative battery cable.
  4. Remove the drive belt and the water pump pulley.
  5. Remove the timing belt cover, timing belt, auto tensioner and idler pulley.
  6. Remove the water outlet fitting, the thermostat case and the water pump fitting.
  7. Remove the water pump mounting bolts.
  8. Remove the water pump.

  9. dc45c19.jpg

    Fig. Water pump and timing belt assembly-exploded view

To install:

1016213.jpg

Fig. Water pump bolt locations
  1. Clean the gasket surfaces of the water pump body and the cylinder block.
  2. Install the new water pump gasket and pump assembly. Tighten the bolts to 12-16 ft. lbs. (17-22 Nm).
  3. Install the water pump fitting, the thermostat case and the water outlet fitting.
  4. Install the auto tensioner and timing belt. Adjust the timing belt tension, then install the timing belt cover.
  5. Install the drive belt, water pump pulley and then adjust the auto tensioner.
  6. Refill the coolant.
  7. Run the engine and check for leaks.

  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Drain the cooling system.
  3. Disconnect the negative battery cable.
  4. Remove the drive belt and the water pump pulley.
  5. Remove the timing belt cover, timing belt, auto tensioner and idler pulley.
  6. Remove the water outlet fitting, the thermostat case and the water pump fitting.
  7. Remove the water pump mounting bolts.
  8. Remove the water pump.

To install:


e9be8c3.jpg

Fig. Water pump bolt locations

596080e.jpg

Fig. Water pump O-ring installation
  1. Clean the gasket surfaces of the water pump body and the cylinder block.
  2. Install the new water pump gasket and pump assembly. Tighten the bolts to 12-16 ft. lbs. (17-22 Nm).
  3. Install the water pump fitting, the thermostat case and the water outlet fitting.
  4. Install the auto tensioner and timing belt. Adjust the timing belt tension, then install the timing belt cover.
  5. Install the drive belt, water pump pulley and then adjust the auto tensioner.
  6. To adjust the drive belt tension, hang the belt on the pulley of the tensioner and install the tensioner.
    NOTE If the tensioner is already installed, loosen its mounting bolts to allow belt installation
  7. Install the drive belt.
  8. Adjust the belt tension to specification by turning the adjusting bolt clockwise or counterclockwise.
  9. Air conditioning belt tension should be 0.28-0.039 inch. Alternator belt tension should be 0.39-0.051 inch. Power steering belt tension should be 0.31-0.051 inch.
  10. Torque the tensioner assembly bolt to 33-36 ft. lbs. (45-50 Nm).
  11. Refill the coolant.
  12. Run the engine and check for leaks.

TY for using Fixya; remember comment and rated this.

Apr 01, 2010 | 2004 Kia Sorento

2 Answers

I have a 1999 Ford SHO that needs a new waterpump. I need to know how to replace it and where I can get a schematic of it. Do I need a special tool kit to do it? I'd also like to know where I can get the...


www.autozone.com

They can get all the parts. They also provide haynes repair manuals, any special tools (probably not required for this vehicle) and any special disassembly instructions.

I hope this helps.

Mar 11, 2010 | 2001 Ford Taurus

1 Answer

How to replace a water pump on a 2003 yukon


Water Pump Replacement (4.8L, 5.3L and 6.0L Engines)
Removal Procedure
1. Drain the cooling system.
2. Loosen the air cleaner outlet duct clamps at these locations:
 Throttle body
 Mass Airflow/Intake Air Temperature (MAF/IAT) sensor
3. Remove the radiator inlet hose clip from the outlet duct.
4. Remove the air cleaner outlet duct.
5. If necessary, remove the engine sight shield.
6. Remove the radiator vent inlet hose from the radiator hose clips.
7. Reposition the inlet hose clamp at the water pump.
8. Remove the inlet hose from the water pump.
9. Remove the fan blade.
11. Reposition the outlet hose clamp at the water pump.
12. Remove the outlet hose from the water pump.
13. Reposition the surge tank outlet hose clamp at the water pump.
14. Remove the surge tank outlet hose from the water pump.
15. Reposition the heater inlet hose clamp at the water pump.
16. Remove the heater inlet hose from the water pump.
17. Remove the water pump bolts.
18. Remove the water pump and gaskets.
19. Discard the water pump gaskets
Installation Procedure Important: All gaskets surfaces are to be free of oil or other foreign material
during assembly.
1. Install the water pump and NEW gaskets
2. Install the water pump bolts.
3. Install the heater inlet hose to the water pump.
Zoom Sized for Print
Notice: Refer to Fastener Notice in Service and Precautions.
2.1. Tighten the bolts a first pass to 15 Nm (11 ft. lbs.).
2.2. Tighten the bolts a final pass to 30 Nm (22 ft. lbs.).
4. Position the heater inlet hose clamp at the water pump.
5. Install the surge tank outlet hose to the water pump.
6. Position the surge tank outlet hose clamp at the water pump.
7. Install the outlet hose to the water pump.
8. Position the outlet hose clamp at the water pump.
9. Install the accessory drive belt.
10. Install the fan blade.
11. Install the inlet hose to the water pump.
12. Position the inlet hose clamp at the water pump.
13. Install the engine vent inlet hose to the radiator hose clips.
14. If necessary, install the engine sight shield.
Important: Align the arrow at the throttle body end of the duct with the throttle
body attaching stud.
15. Install the air cleaner outlet duct
16. Install the radiator inlet hose clip to the outlet duct.
17. Tighten the air cleaner outlet duct clamps at these locations:
 Throttle body
 MAF/IAT sensor Tighten the clamps to 7 Nm (62 inch lbs.).
18. Fill the cooling system.

I hope this helps. The numbering is incorrect in the sequence but the instructions are correct.

Roy

Nov 06, 2009 | 2003 GMC Yukon

1 Answer

1991 bmw 318is 4 door 16 valve motor, runs hot and radiator cold


you may have bad waterpump,the impeller on pump may be borken, just because it doesnt leak doesnt mean its good.also could have exhaust entering cooling system (bad headgasket) if pump is good have a block test done.

Sep 29, 2009 | BMW 318 Cars & Trucks

1 Answer

Specs for 1992 3cyl diahatsu charade ignition timing


Timing set with vacuum hoses disconnected and blocked is 5° advanced when flywheel dimple lines up with notch plate.

centrif wieghts 10.5° @ 2800
vacuum two stage 11° @ -320mmHg.

Feb 19, 2009 | 1992 Daihatsu Charade

Not finding what you are looking for?
1992 Daihatsu Charade Logo

661 people viewed this question

Ask a Question

Usually answered in minutes!

Top Daihatsu Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

yadayada
yadayada

Level 3 Expert

79865 Answers

Donald DCruz
Donald DCruz

Level 3 Expert

17130 Answers

Are you a Daihatsu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...