Question about 2001 Daewoo Nubira

2 Answers

Stereo does not work, dial reads, cod ? Is there a reset code to make the entire system go on?? I just bought this 2001 Nubia and the display lights up but that`s all.....

Posted by on

  • lucilleferra May 11, 2010

    I WAS HOPING FOR A LITTLE FREE ADVICE, OBVIOUSLY I WAS MISINFORMED1

×

Ad

2 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

Try the last 4 digits of the radio's serial number (s/n or s#)

or try the following general codes:

4316 2152 4513 4362
1156 2145 3451 6361
5624 5241 3346 1165
3241 4524 5436 1165 4362 5813 4513 5241 4316 1651 5346 1341 3241 1652 4524 6361 2145 5436 1857 4353 5632 3451 1638 1156 1636 5324

Posted on Jan 24, 2010

  • mcchamp1 Jul 07, 2011

    I went through the code list you have and one of the numbers worked. Thank You!

×

Ad
  • Level 1:

    An expert who has achieved level 1.

    New Friend:

    An expert that has 1 follower.

  • Contributor
  • 1 Answer

I tried all these codes none of them worked

Posted on Feb 02, 2015

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

How do i reset the esp ecu on my 2006 mercedez cls 500?


Disclaimer:
Please take your car to a professional to reset the ECU.
READ THIS ENTIRE PROCEDURE BEFORE GETTING STARTED

The difererence between having the dealer reset your ECU and you doing it is that the dealer only clears the faults, the ECU has a memory, so when you reset your ECU, it must basically re-calibarte itself and learn about all your car's systems from scratch.

BEGINNING Steps:
1. Center your steering wheel.
2. Make sure your windows are all the way up
3. Make sure your sun roof is completely closed
4. make sure your parking brake is released
6. Turn off your stereo.
7. Make sure you have your stereo's Anti-theft code
8. Turn off your heat/AC blower
9. Turn off your lights
10. Make sure your doors are UNLOCKED.

Reset Steps:
Open your trunk and disconnect the negative side of your battery, wait 60 seconds and re-connect it.

AFTER the RESET

Turn the key to position 2 (DO NOT START YOUR ENGINE)

1. Reseting your windows: Run windows down to the dwn/up full stop, then hold an extra 5 seconds (you might have to run these to the full up/dwn position an inch at a time, just keep going until you hit full open/closed position, then hold an additional 5 seconds). This re-enables the "auto up/dwn". Do the same thing with the sunroof. If it didn't work for the sunroof, then try this: remove the sunroof fuse, then re-insert it. then do the same procedure as above.

2. Turn on your blower and make both sides go to 72 deg. by pressing both up and down buttons at the same time. This should help calibrate the ECU

3. Turn on your stereo and enter your stereo code. if you do not have a code, you'll have to get it from the dealer. or perform endless searches on the web for a fix for that.

5. Turn all of the lights on and off, including your fog lights

6. Turn the key back to position 0.

7. Turn on your engine. You will get 2 malfunctions, your ABS and ESP, These systems must be calibrated. Calibrate your ABS and ESP systems by turning the steering wheel all the way to your RIGHT and then all the way to your LEFT. then bring it back to the center. The errors should go away from your instrument cluster.

8. Let your car run at idle for about 5 minutes and then take it for a spin. Remember your ECU is still getting all the readings from all the sensors, so drive slowly first then faster... and so on.. you are basically your ECU is re-learning your car.

Hope this helps, and remember, you are doing this at your own risk!

Sep 08, 2014 | 2006 Mercedes-Benz CLS 500

1 Answer

I have a 2008 ford ranger xlt 4x4 4.0 truck. we changed the motor and sense the battery was disconnected the anti theft system locked down how do we unlock it.


follow this steps and fix it. God bless you

Turn the vehicle on. The engine does not need to be running but the ignition should be on to power the stereo.


  • 2 Press the "Source" or "Power" button to turn the unit off.


  • Sponsored Links

  • 3
    Press and hold down the "Minute" button (located to the left of the GM vehicle stereo's display. Some models require pressing and holding the left arrow button if no "Minute" button is present.) Release the button once the display shows "0000."

  • 4
    Press the "Minute" button (or left arrow) to set the value of the third and fourth digits of the anti-theft code. Release the button once the proper value for the last two digits is displayed.

  • 5
    Press the "Hour" button (or right arrow button) to set the first and second digits of the code. Release the button once the four-digit code is accurately displayed.

  • 6
    Press the "Mode" button to lock in the code you set. Turn the stereo deck on by pressing the "Source" or "Power" button to complete the reset.


  • Read more: http://www.ehow.com/how_6924001_reset-anti_theft-code-car-stereo.html#ixzz2gZHpH2aT

    Oct 02, 2013 | 2001 Ford Ranger Regular Cab

    1 Answer

    After AAA replaced the vehicle battery, my car stereo stopped working. The only indication the stereo is still powered is the treble, bass, and balance slide knobs are blinking. I assume there is a...


    go to your vehicle owners manual for reset radio code. if it's a stock radio or stereo system the code will be there.or there is a site on fixya.com for reset radio code.you will need to spend about $2.00 to get the code however.thank you for choosing fixya.com

    Jan 26, 2011 | 2001 Plymouth Neon

    3 Answers

    How do I do a Diagnostic System Check? Is this


    If you can visit one autozone shop, they can read or scanning your OBD codes.

    Codes are displayed on digital odometers on newer models. On many 2001 and newer models, holding in the trip odometer reset button while turning the key to RUN will start a self test, with a readout on the odometer. It will also activate all instrument panels, one at a time. We do not know if this will show computer codes, or whether it only tests the instrument panels. At the end, it may show a few odd codes that are firmware versions and not error codes.

    On most cars, the codes will read out if the engine light is on - all you have to do is put the key into the RUN position.

    Normally, to get codes, you put the key on OFF and then rapidly do OFF-ON-OFF-ON-OFF-ON (on some cars you have to do four or five, not three, OFF-ON cycles). On our test 2002 car, the key did not go back to unlock, so it was ACC-ON-ACC-ON-ACC-ON.

    • You may have to have the parking brake firmly set for the codes to show! (Thanks, Steven Midway)
    • Jon Yoon: The 1998 Caravan does the same check engine light code trick, but it also does an instrument diagnostic check if you hold the trip and reset buttons and turn the key to the run position and wait 5 seconds. This helped me figure out that my input and output speed sensors were broken but the actual speedometer dial could move.
    • For the 1999 Jeep Grand Cherokee and up, you do the switching the key on and off 3 times, but not quickly. You turn it to on so the odometer turns on, turn it off, and then back on, wait for the light to turn on, etc. On the fourth time you'll get a code, or you'll get the word "done." (Monica MacDonald)
    A loose gas cap may light up the Check Engine light! (Thanks, Lyn Clark)
    • When the computer indicates major failure, it can activate Limp In mode, which guesses about data to compensate for sensor failure, allowing you to get the car to a mechanic. One major symptom of this is the transmission sticking in second gear. This is a feature!
    • 2002 Ram, put transmission in neutral, parking brake on, then do the acc-run key sequence 3 times.
    • Dan Stewart wrote about the 1999+ Voyager/Caravan with digital gear selection display:
      • There are 2 functions that can be accomplished with the key-on sequence. Get Diagnostic Trouble Codes by placing the key into the ignition. Push and hold the both the "Trip" and the "Reset" buttons with the left hand and turn the key to the "ACC" position (first position between "LOCK" and "RUN"). Continue to hold both buttons in and count to 5. Release both buttons, display should read trip mileage instead of total mileage. Push the "TRIP" button and the odometer will display DTC'S in rotating sequence instead of displaying total mileage.
      • The second function is an instrumentation diagnostic. Place key into ignition, press and hold both "TRIP" and "RESET" while turning the key to the "RUN" position. Continue to hold both buttons in until odometer displays "CODE". Release buttons. The display will then display "999". Afterward it will display "CHECK 0" and test the analog gauges. It will then display "CHECK 1" and test the digital displays

    RESET THE COMPUTER
    Normally the computer will eventually reset itself; you can also use a scan tool. (See our transmission repair page for information on resetting the computer's transmission information.) Disconnecting the battery for a few minutes generally resets the computer, though it also means losing clock settings.
    Sid Willoughby wrote: “To clear the check engine light on a 2002 Dodge Ram once the problem is resolved. Start the engine and drive forward then in reverse (you only have to move the truck a few feet in each direction) the turn the ignition off. Do this sequence three times. When you start the vehicle the fourth time the check engine light should go out.” (This procedure may well work on other vehicles.)

    CODE LIST 2001 which covers some vehicles from the late 1990s as well as newer ones. It shows the longer codes starting with the letter P.

    Hope this help (remember comment and rated this).


    Apr 09, 2010 | 2001 Dodge Caravan

    2 Answers

    How do I reset the service engine soon light on 2001 Olds Silhouette


    A diagnostic scanner that reads OBD1 (the system by which your vehicle processes trouble codes) will be required, many parts stores do this a s a free service. Check with them to see if they charge. Remember though, when they read the car and turn the light off that in order for the light to stay off, the problem must be fixed. Even if it was a one time fluke of a problem, get the code that their scanner gives them so that you know what the issue is.

    Dec 10, 2009 | 2001 Oldsmobile Silhouette

    1 Answer

    The stereo has stopped working and is displaying


    mine was 4513.... or try the list of codes on this site. They work....Thank GOD.

    Nov 29, 2009 | 2004 Suzuki Verona

    1 Answer

    2001 acura TL stereo unlock code


    I have a 2001 Acura TL that I bought a month ago and the stereo volume wont go up past 1. Do i need to replace it or unlock it?

    Sep 18, 2009 | 2001 Acura 3.2TL

    1 Answer

    My readio reads off how do i trun it back on to put the code in. my kid put the worng cod in three times and now it reads off instead of cod. pleas help


    i read a solution online that said just turn car on, but don't actually turn over the engine, then turn the stereo and let it read off for 1 hour. The car has to sit in this idle state for one solid, continuous hour, then the screen should go blank. Turn on the stereo system again and it is once again read for the code to be input.

    Jun 20, 2009 | 2002 Mitsubishi Eclipse Spyder

    1 Answer

    After dead battery, radio won't work. lights...


    you need to call your local dealership and they will give you the code to reset you radio.. good luck keith..p.s. remeber to write down the codes, that way if it happens again you will have the code for the radio..

    Mar 21, 2009 | 2001 Dodge Intrepid

    3 Answers

    Vw golf petrol 2.0 2001


    Hi there,

    There's one more thing you can try. On a Mk4 VW, you can reset the service indicator by doing the following:

    - With the ignition off, press and hold the tripmeter reset button (on the right side of the dash)
    - Turn on your ignition, wait for all the warning lights to come on, then let go of the tripmeter button
    - Where your trip distance is normally shown, the display will read "OIL".
    - To reset the service interval, turn the clock adjust switch (left side) for about 5 seconds. The trip meter display will change to "---" indicating the code has been reset.

    You can verify this by turning the car off and on again. Let me know if that worked out for you.

    Aug 11, 2008 | 2001 Volkswagen Golf

    Not finding what you are looking for?
    2001 Daewoo Nubira Logo

    Related Topics:

    171 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Daewoo Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22382 Answers

    Marvin
    Marvin

    Level 3 Expert

    83083 Answers

    Jeffrey Turcotte
    Jeffrey Turcotte

    Level 3 Expert

    8841 Answers

    Are you a Daewoo Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...