Question about 2003 Kia Sedona

1 Answer

I need to replace the front and rear oxygen sensors on my Kia Sadona. Each sensor has a cable coming out of the top. Is there some kind of special socket or tool to extract and install these sensors?

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 91 Answers

You can get a special socket but a normal spanner will suffice

Posted on Dec 31, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Check engine light is on. code P0140 on 2006 Kia Rio


- Faulty Rear Heated Oxygen Sensor Bank 1
- Rear Heated Oxygen Sensor Bank 1 harness is open or shorted
- Rear Heated Oxygen Sensor Bank 1 circuit poor electrical connection
- Inappropriate fuel pressure
- Faulty fuel injectors
- Intake air leaks may be faulty
- Exhaust gas leaks
Replacing the Rear Heated Oxygen Sensor Bank 1 usually takes care of the problem.

Oct 13, 2013 | 2006 Kia Rio

1 Answer

I have a kia sadona and need to replace my rack and pinion. Can I replace it without taking engine out???


To install a camshaft replacement sensor on a 2003 Kia Sedona you will need a screwdriver, a wrench, a break bar and socket, and a camshaft position sensor. To install, make sure the vehicle's ignition switch is turned off and disconnect the negative cable from the battery. Remove the air filter housing from the car by unscrewing the bolts that secure the lid. Rotate the crankshaft. Locate the cylinder head and mount the camshaft sensor onto the cylinder head.---------------------------------------------------------------------------
XPROG-M

Apr 18, 2013 | Cars & Trucks

1 Answer

FOR A 1997 HONDA ACCORD LX WHAT IS THE DIFFERENCE BETWEEN OXYGEN SENSOR BLOCK1 AND BLOCK2, AND HOW CAN I INSTALL THE OXYGEN SENSOR? WHAT WOULD I NEED TO INSTALL IT WITH(ANY SPECIAL TOOL?) AND WHY IS T


The bank 1 is the one before the catalytic converter (that would be in line in the exhaust pipe just after the engine), No 2 is after, in the middle of the car, and if you are lucky a 7/8 wrench would do.

Feb 02, 2013 | Honda Accord Cars & Trucks

1 Answer

Where is the o2 sensor on a 2004 blazer located


Removal & Installation

Raise and support the vehicle.
Support rear of the powertrain frame.
Remove four rear frame bolts.
Lower the frame no more than 73.2 mm (3 inches).
Disconnect the rear oxygen sensor electrical connector.
Remove the rear oxygen sensor from the rear exhaust manifold.

To install:

Install the rear oxygen sensor in the rear exhaust manifold. Tighten the rear heated oxygen sensor (HO2S) sensor to 41 Nm (30 ft. lbs.).
Connect the rear oxygen sensor connector.
Raise the frame.
Install the four rear frame bolts. Tighten the frame bolts to 100 Nm (74 ft. lbs.).
Lower the vehicle.


Heated Oxygen Sensor Bank 1 Sensor 1 (HO2S 1/1)

WARNING: Handle the oxygen sensors carefully in order to prevent damage to the component. Keep the electrical connector and the exhaust inlet end free of contaminants. Do not use cleaning solvents on the sensor. Do not drop or mishandle the sensor.

CAUTION: Remove oxygen sensors with the engine temperature above 48C (120F). Otherwise the oxygen sensors may be difficult to remove.

A special anti-seize compound is used on the oxygen sensor threads. New service sensors should already have the compound applied to the threads. Coat the threads of a reused sensor with anti-seize compound P/N 5613695 or equivalent.

11_14_2011_1_39_03_pm.jpg

Fig. Showing the location of the HO2S Bank 1 Sensor 1

Heated Oxygen Sensor Bank 1 Sensor 2 (HO2S 1/2)

CAUTION
Handle the oxygen sensors carefully in order to prevent damage to the component. Keep the electrical connector and the exhaust inlet end free of contaminants. Do not use cleaning solvents on the sensor. Do not drop or mishandle the sensor.

CAUTION: Remove oxygen sensors with the engine temperature above 48C (120F). Otherwise the oxygen sensors may be difficult to remove.

WARNING: A special anti-seize compound is used on the oxygen sensor threads. New service sensors should already have the compound applied to the threads. Coat the threads of a reused sensor with anti-seize compound P/N 5613695 or equivalent.

11_14_2011_1_40_07_pm.jpg

Fig. Showing the location of the HO2S Bank 1 Sensor 2

Raise and support the vehicle.
Remove the heat shield.
Disconnect the heated oxygen sensor electrical connector.
Remove the heated oxygen sensor.

To install:

Install the heated oxygen sensor. Tighten the heated oxygen sensor (HO2S) to 41 Nm (30 ft. lbs.).
Connect the heated oxygen sensor electrical connector. CAUTION
Ensure connectors are securely installed beneath harness heat shield to prevent damage.
Install the heat shield.
Lower the vehicle.


Heated Oxygen Sensor Bank 2 Sensor 1 (HO2S 2/1)

CAUTION: Handle the oxygen sensors carefully in order to prevent damage to the component. Keep the electrical connector and the exhaust inlet end free of contaminants. Do not use cleaning solvents on the sensor. Do not drop or mishandle the sensor.

CAUTION: Remove oxygen sensors with the engine temperature above 48C (120F). Otherwise the oxygen sensors may be difficult to remove.

WARNING: A special anti-seize compound is used on the oxygen sensor threads. New service sensors should already have the compound applied to the threads. Coat the threads of a reused sensor with anti-seize compound P/N 5613695 or equivalent.

Raise and support the vehicle.
Remove the air deflector.
Disconnect the front oxygen sensor electrical connector.
Remove the front oxygen sensor from the front exhaust manifold.

11_14_2011_1_37_39_pm.jpg

Fig. Showing the location of the HO2S Bank 2 Sensor 1

To install:
Install the front oxygen sensor in the front exhaust manifold. Tighten the front HO2S sensor to 41 Nm (30 ft. lbs.).
Connect the front oxygen sensor electrical connector.
Install the air deflector.
Lower the vehicle.

Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

Oct 14, 2011 | Cars & Trucks

1 Answer

Location of oxygen sensor on 2004 blazer check engine light keeps coming on. Replaced sensor no change. At bank 1 sensor is not connected when tested.


Removal & Installation

Raise and support the vehicle.
Support rear of the powertrain frame.
Remove four rear frame bolts.
Lower the frame no more than 73.2 mm (3 inches).
Disconnect the rear oxygen sensor electrical connector.
Remove the rear oxygen sensor from the rear exhaust manifold.

To install:

Install the rear oxygen sensor in the rear exhaust manifold. Tighten the rear heated oxygen sensor (HO2S) sensor to 41 Nm (30 ft. lbs.).
Connect the rear oxygen sensor connector.
Raise the frame.
Install the four rear frame bolts. Tighten the frame bolts to 100 Nm (74 ft. lbs.).
Lower the vehicle.


Heated Oxygen Sensor Bank 1 Sensor 1 (HO2S 1/1)

WARNING: Handle the oxygen sensors carefully in order to prevent damage to the component. Keep the electrical connector and the exhaust inlet end free of contaminants. Do not use cleaning solvents on the sensor. Do not drop or mishandle the sensor.

CAUTION: Remove oxygen sensors with the engine temperature above 48C (120F). Otherwise the oxygen sensors may be difficult to remove.

A special anti-seize compound is used on the oxygen sensor threads. New service sensors should already have the compound applied to the threads. Coat the threads of a reused sensor with anti-seize compound P/N 5613695 or equivalent.

11_14_2011_1_39_03_pm.jpg

Fig. Showing the location of the HO2S Bank 1 Sensor 1

Heated Oxygen Sensor Bank 1 Sensor 2 (HO2S 1/2)

CAUTION
Handle the oxygen sensors carefully in order to prevent damage to the component. Keep the electrical connector and the exhaust inlet end free of contaminants. Do not use cleaning solvents on the sensor. Do not drop or mishandle the sensor.

CAUTION: Remove oxygen sensors with the engine temperature above 48C (120F). Otherwise the oxygen sensors may be difficult to remove.

WARNING: A special anti-seize compound is used on the oxygen sensor threads. New service sensors should already have the compound applied to the threads. Coat the threads of a reused sensor with anti-seize compound P/N 5613695 or equivalent.

11_14_2011_1_40_07_pm.jpg

Fig. Showing the location of the HO2S Bank 1 Sensor 2

Raise and support the vehicle.
Remove the heat shield.
Disconnect the heated oxygen sensor electrical connector.
Remove the heated oxygen sensor.

To install:

Install the heated oxygen sensor. Tighten the heated oxygen sensor (HO2S) to 41 Nm (30 ft. lbs.).
Connect the heated oxygen sensor electrical connector. CAUTION
Ensure connectors are securely installed beneath harness heat shield to prevent damage.
Install the heat shield.
Lower the vehicle.


Heated Oxygen Sensor Bank 2 Sensor 1 (HO2S 2/1)

CAUTION: Handle the oxygen sensors carefully in order to prevent damage to the component. Keep the electrical connector and the exhaust inlet end free of contaminants. Do not use cleaning solvents on the sensor. Do not drop or mishandle the sensor.

CAUTION: Remove oxygen sensors with the engine temperature above 48C (120F). Otherwise the oxygen sensors may be difficult to remove.

WARNING: A special anti-seize compound is used on the oxygen sensor threads. New service sensors should already have the compound applied to the threads. Coat the threads of a reused sensor with anti-seize compound P/N 5613695 or equivalent.

Raise and support the vehicle.
Remove the air deflector.
Disconnect the front oxygen sensor electrical connector.
Remove the front oxygen sensor from the front exhaust manifold.

11_14_2011_1_37_39_pm.jpg

Fig. Showing the location of the HO2S Bank 2 Sensor 1

To install:
Install the front oxygen sensor in the front exhaust manifold. Tighten the front HO2S sensor to 41 Nm (30 ft. lbs.).
Connect the front oxygen sensor electrical connector.
Install the air deflector.
Lower the vehicle.

Hope this helps; also keep in mind that your feedback is important and I'll appreciate your time and consideration if you leave some testimonial comment about this answer.

Thank you for using Fixya, and have a nice day.

Oct 12, 2011 | Cars & Trucks

1 Answer

My 2003 Kia Optima check engine light keeps coming on. I was told "Bank 1 Sensor 1" needs to be replaced. Where is Bank 1 Sensor 1?


P0130 Oxygen Sensor Circuit Malfunction - Bank 1 Sensor 1.
P0131 Oxygen Sensor Circuit Low Voltage - Bank 1 Sensor 1.
P0132 Oxygen Sensor Circuit High Voltage - Bank 1 Sensor 1.
P0133 Oxygen Sensor Circuit Slow Response - Bank 1 Sensor 1.
P0134 Oxygen Sensor Circuit No Activity detected - Bank 1 Sensor 1.
P0135 Oxygen Sensor Heater Circuit Malfunction - Bank 1 Sensor 1


Jun 23, 2010 | 2003 Kia Optima

1 Answer

1996 spotage kia p0422


P0422 Main Catalyst Efficlency Below Threshold (Bank 1) The catalyst’s efficiency is demonstrated by its ability to oxidize CO and hydrocarbon emissions. The Engine Control Module (ECM) compares the output signals of the front and rear oxygen sensors to determine whether the output of the rear sensor is beginning to match the output of the front oxygen sensor. Air/fuel mixture compensation keeps the frequency of the front oxygen sensor high due to the changes from rich-to-lean comvustio. The catalyst causes the rear oxygen sensor to have a lower frequency. As the catalyst wears, the rear oxygen sensor’s signal trace begins to match the front oxygen sensor’s signal trace. That is because the catalyst becomes saturated with oxygen and cannot use the oxygen to convert hydrocarbon and CO into H₂O and CO₂ with the same efficiency as when it was new. A completely worn catalyst shows a 100% match between the frequency of the front and rear sensors. The ECM sets P0422 if the average of caculated oscillation size of rear HO2S value is higher than threshold value during predetermined time.

Apr 23, 2010 | 2000 Kia Sportage

1 Answer

Change oxygen sensor


Under hood, center, front engine area, above exhaust pipe flange, mounted in exhaust manifold
Application:
Front
Under hood, center, rear engine area, above exhaust pipe flange, mounted in exhaust manifold
Application:
Rear

The oxygen sensor may be difficult to remove when the engine temperature is below 120°F (48°C). Excessive force may damage the threads in the exhaust manifold of exhaust pipe.
  1. Start the engine and let it warm up to 120°F (48°C), stop the engine and disconnect the negative battery cable.
  2. Detach the electrical connector from the oxygen sensor.
  3. Using a special, oxygen sensor socket, remove the oxygen sensor from the exhaust manifold or exhaust pipe.


NOTE A special anti-seize compound is used on the oxygen sensor threads. The compound consists of liquid graphite and glass beads. The graphite will burn away, but the glass beads will remain, making the sensor easier to remove. New or service sensors will already have the compound applied to the threads. If an oxygen sensor is removed from the engine and if for any reason, it is to be reinstalled, the threads must have this anti-seize compound applied before installation.
  1. Coat the threads of the oxygen sensor with anti-seize compound 5613695 or equivalent.
  2. Install the sensor and tighten it to 30 ft. lbs. (40 Nm).
  3. Reattach the electrical connector to the sensor and the negative battery cable.



0900c1528025ed0c.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Location of the rear O2 sensor


0900c1528025ed0d.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Location of the the front O2 sensor


0900c1528025ed0e.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. Use a wrench or special socket to loosen the O2 sensor


0900c1528025ed0f.jpg enlarge_icon.gifenlarge_tooltip.gif Fig. When replacing or reinstalling an oxygen sensor, be sure to lube the threads sufficiently

Jan 19, 2010 | 1992 Cadillac DeVille

3 Answers

Were on exaust is oxygen sensor in 1999 subaru impreza auto sport


On the SOHC engine the front (A/F) oxygen sensor is located in the front section of the front catalytic converter. The rear oxygen sensor is located in the rear section of the front catalytic converter. On the DOHC engine the front oxygen sensor is located in the front section of the exhaust system, just past the crossover pipe. The rear oxygen sensor is located in the front section of the catalytic converter.

Oxygen sensor location-Baja 2.5L SOHC engine
c3fce0b.jpg

Oxygen sensor location-Baja 2.5L DOHC engine
7aac75e.jpg


On the 2.0L engine the front (A/F) oxygen sensor is located in the front section of the exhaust system, just past the crossover pipe. The rear oxygen sensor is located in the front section of the rear catalytic converter. On the 2.2L engine the front (A/F) oxygen sensor is located in the front section of the front catalytic converter. The rear oxygen sensor is located in the rear section of the rear catalytic converter.

Oxygen sensor location-Impreza 1998-2001 2.2L engine
a5973e4.jpg


moz-screenshot.pngOxygen sensor location-Impreza 1998-2002 2.5L SOHC engine
3a84717.jpg
I hope helped with this; remember rated this help. Good luck.

Nov 20, 2009 | 1999 Subaru Impreza

Not finding what you are looking for?
2003 Kia Sedona Logo

Related Topics:

219 people viewed this question

Ask a Question

Usually answered in minutes!

Top Kia Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22382 Answers

Marvin
Marvin

Level 3 Expert

83036 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Kia Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...