Question about 2001 Jeep Grand Cherokee

1 Answer

Exactly where is oil pressure sending unit located on 2001 Jeep Grand cherokee. PLEASE don't tell me it is near the oil pump.

Posted by on

  • Anonymous Mar 16, 2014

    I have a 1997 ford contour with the 2 5liter v6 dual over head cam 24valve motor Can anyone tell me where the oil pressure sending unit sensor is I believe I located it to the rear of the block near the oil pan My gauge does not work any more and I hope that this is the problem

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 5,081 Answers

If you have the 5.2 V8 its located in the rear of the engine near the dist cap area you can see it if you look in that area , if 4.0 6 cyl its located on the side of the engine block near the oil filter area. It has two wires going to it and screws into the block. It's made mainly of plastic and if broken can allow oil under pressure to spew out and give you thoughts of a blown rear main seal due to the amount of oil all over the underside.

Posted on Dec 09, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the oil pressure sending unit located on a 2000 jeep grand cherokee 4.0 liter


Removal & Installation
  1. Disconnect the negative cable from the battery.
  2. Raise vehicle on hoist.
  3. Remove front splash shield.
  4. Disconnect oil pressure sender connector (4).
  5. Remove the pressure sender (2).
6eaedba.gif
Oil pressure sending unit


To install:
  1. Install oil pressure sender.
  2. Connect oil pressure sender wire.
  3. Install front splash shield.
  4. Lower vehicle.
  5. Connect the negative battery cable.

Jan 12, 2010 | 2000 Jeep Grand Cherokee

2 Answers

What causes the oil pressure gauge to fluctuate on my 2004 Jeep Grand Cherokee Laredo?


If the oil pressure is good and there is no engine noises then the oil pressure sending unit is the problem.Just replace it and you should be good.Hope this helps.Good luck.

Jan 07, 2010 | 2004 Jeep Grand Cherokee

1 Answer

I have 2001 jeep grand cherokee 6cyl need


On the top of the bellhousing. From the drivers point of view it is in the 11:00 o'clock position. The harness wraps around the back of the bellhousing and plugs in on the passenger side of the block near the oil sending unit.

Oct 25, 2009 | 2001 Jeep Grand Cherokee

2 Answers

2001 Jeep Oil Pressure


Last week my 2001 Grand Cherokee with a 4.7 was dropping below 10 and my "check gauges" light and chime came on. My sending unit was bad. I could see it was bad because oil was getting through the unit and leaking very slow. It's located above the oil filter. Easy fix, but the unit was over $50 and the 1 1/16 special deep socket for sending units was over $10.

Oct 07, 2009 | 2001 Jeep Grand Cherokee

2 Answers

Where is the location of the oil pressure sending unit on a 2000 jeep grand cherokee 4x4


Someone comments say...

- On my 95 4.0 it's right beside the distributor.
- The sensor is on the passenger side of the engine, back near the firewall.

Good luck!!

Jul 14, 2009 | 2000 Jeep Grand Cherokee

1 Answer

I have a 96 Jeep Grand Cherokee (4 L) with 225,000 miles. When idling and engine hot, oil pressure guage drops to zero. Any way to tell if it is the pressure sensing unit or not?


ook up a external pressure guage where the sending unit is you will know forsure. with the milage i would guess that the oil pump may be the prblem or to much clearance in yhe bearing.

Jun 10, 2009 | 2002 Jeep Grand Cherokee

1 Answer

Low oil pressure


the first i would do is to see if the oil sending unit is ok and if you gage is working right and if they are then checkout the oil pump.

Feb 14, 2009 | 2001 Jeep Grand Cherokee

3 Answers

OIL PRESSURE SENDING UNIT ON MY JEEP CHEROKEE 1993 WHERE IS IT LOCATED AND IS THERE A DIAGRAM OR PICTURE LOCATION FOR IT


OIL PRESSURE SENDING UNIT ON MY JEEP GRAND CHEROKEE LAREDO 1999
WHERE IS IT LOCATED AND IS THERE A DIAGRAM OR PICTURE LOCATION FOR IT

ANY SPECIAL KNOWLEDGE TO PUT IN?

Jul 30, 2008 | 1999 Jeep Cherokee

Not finding what you are looking for?
2001 Jeep Grand Cherokee Logo

1,327 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

80407 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...