Question about 2001 Isuzu Rodeo

1 Answer

When lights are on when pressing the brake pedal the brake light goes off; with the light off the brake light works ok.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 486 Answers

YOU HAV A BAD EARTH IN THE CLUSTER AND CAUSING THE POWER TO USE THE OTHER CIRCUITS, U NEED TO REMOVE THE UNIT AND CLEAN UP ALL CONECTERS, AND CHECK THE MAIN EARTH CICUIT IS GROUNDED

Posted on Dec 09, 2009

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brake lights won't work


Check bulbs. If ok, check fuse. If ok. check brake light switch on brake pedal. If ok, the brake light circuit goes through the signal light switch and it may be defective

Jan 21, 2016 | 2000 GMC Safari

1 Answer

2001 Chevy Cavalier no brake lights but turn signals/hazards/backups work just fine. any ideas?


WHEN YOU APPLY BRAKE PEDAL, do you see brake lights come on ? if no then the switch is not working fine ! switch turns lights on when you depress the pedal, releasing the plunger, lights go out when you release the pedal. this switch has a fuse @ fuse block. check it ! if ok, and brake lights do
not come on replace switch, & mount properly in bracket.

Mar 08, 2013 | 2001 Chevrolet Cavalier

2 Answers

Renault megane, 2004 1.4 dynamique, brake lights not working (both sides but high level one ok) have checked bulbs, fuses, connections at cluster, loom in areas for visible damage, all other lights ok


Seems to me that the brake lights switch has a problem there is a way to test this problem, you normally press the clutch pedal and hold down the start button to start the engine, now try pressing the break pedal down and hold the start button, if the car does not start up change the brake pedals switch.

Apr 11, 2010 | 2004 Renault 181

1 Answer

Car brack light on all the time#


hi, this is a common problem what you need to do is get on the floor by the foot pedals and look closely at the brake pedal then follow the brake pedal right to the top of the pedal then just before it goes through the bulk head into the engine you will see a switch atatched to the base of the brake pedal it will have 2 or 3 wires going to it now you may find the brake switch has come away from the pedal if so place it back where it should be no if the brake switch is still atatched then the chances are the switch has wore causing the gap between the switch and the pedal to be to big now you need to either replace the switch or build up the part on the brake pedal that presses the switch with something like sellotape to make the gap smaller so the switch is pressed when you press the brake pedal now this wont be a permanent fix but will get your brake lights working again.

The switch itself is not expensive so your best option would be to replace the brake light switch.

Let me know how you get on or if you need further assistance ok

Feb 07, 2010 | 2005 Peugeot 405

1 Answer

2005 f150 4by4 brakes


Hello

With regards to the brake lights, you need to replace your brake switch located under your brake pedal.

With regards to spongy pedal, sounds like air in the line you need to bleed the brakes via the bleed nipple on each caliper and check your brake fluid.

hope this helps.

Thanks

Mar 17, 2009 | 2005 Ford F-150

1 Answer

Rere light goes out when brake pressed.


HI THIS IS V/COMMON ON THIS CAR, IT IS A BAD EARTH ON ONE OF THE REAR LAMPS IF YOU UNPLUG THE WIREING THAT FITS IN THE LAMP YOU WILL SEE WHITE CORRODING ON THE TABS GIVE THEN A RUB WITH SOME LIGHT SANDPAPER TILL SILVER THEN A SPRAY WITH WD40 TO PROTECT THEM, AND ALL WILL WORK AGAIN THANKS.

Feb 20, 2009 | 2005 Peugeot 405

1 Answer

Rear brake lights wont work on our 2005 chevy aveo ????


It sounds like you should check for power at brake pedal switch. Hook up a test light to the switch and press the brake pedal. If the light does not go on and you have power in the wires to the switch then the switch should be replaced.
I hope this helps you out

Nov 24, 2008 | 2005 Chevrolet Aveo

Not finding what you are looking for?
2001 Isuzu Rodeo Logo

Related Topics:

89 people viewed this question

Ask a Question

Usually answered in minutes!

Top Isuzu Experts

yadayada
yadayada

Level 3 Expert

79186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14406 Answers

Are you an Isuzu Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...