What are the cylinderhead torque settings for Fiesta 1.4 Duratech

2012 ford fiesta cylinder head torque?

Fiesta Faction https://www.fiestafaction.com > threads > 2012-ford-fi...
May 18, 2018 - Tighten to 15 Nm (133 lb-in.) Tighten to 35 Nm (26 lb-ft.) Tighten an additional 75 degrees. There's a tightening order, but the manual doesn't ...

Need cylinder head torque specs for 2013 ford fiesta 1.6 L.

JustAnswer https://www.justanswer.com > Car Questions
May 29, 2018 - - Stage 1: Tighten to 5 Nm (44 lb-in). - Stage 2: Tighten to 15 Nm (133 lb-in). - Stage 3: Tighten to 35 Nm (26 lb-ft). - Stage 4: Tighten an ...

1 answer · Top answer: yes it is you can always get me back through here even after you rate me.

Pictures of tightening sequence

https://www.google.com/search?q=Ford+Fiesta+2011+torque+settings+cylinder+head

..

Ford Fiesta Fiesta 1.6 16V Duratec (1595ccm) 2002-2008

https://www.carrepairdata.com > eng > fiesta > fyja__fyjb
Ford Fiesta Fiesta 1.6 16V Duratec (1595ccm) 2002-2008 ; Cylinder head tightening torque 1, 15Nm ; Cylinder head tightening torque 2, 30Nm.

Torque Specifcations - MAHLE Aftermarket

https://www.mahle-aftermarket.com > media > torque3
PDF
Rod Torque. Main Torque. Cylinder Head Bolt Torque. ACURA. 1.6 ... 55-60 FT/LBS. FORD. 2.5. 155. DURATEC. 95-02. 26-33 FT/LBS, + 90-120^ USE. NEW BOLTS.

Here are the torque settings for a Ford Fiesta 1.4 2010 for the main bearings, head bolts, and big ends:
Main bearings

• Main bearing caps: 1st stage - 7 Nm, 2nd stage - 16 Nm
• Main bearing bolts: 45 Nm + 90°

Head bolts

• Cylinders 1-3: 2nd stage - 30 Nm + 90°, 3rd stage - 80 Nm + 180°
• Cylinder 4: 2nd stage - 25 Nm + 90°, 3rd stage - 60 Nm + 180°

Big ends

• Connecting rod cap nuts: 1st stage - 22 Nm, 2nd stage - 40 Nm + 90°

Please note that these are just the general torque settings. The exact torque settings may vary depending on the specific engine and vehicle. It is always best to consult your vehicle's service manual for the correct torque settings.
Here are some additional tips for tightening the torque settings:

• Use a torque wrench to ensure that the bolts are tightened to the correct torque.
• Tighten the bolts in a star pattern, working your way from the center out.
• Do not overtighten the bolts, as this can damage the engine.

There's a website that has all this information about all this and manuals everything totally free there are many actually but I personally like few .. let me know if u need help
thanks

Toyota Yaris Main and Big end Torque settings:
Tighten the main and big end bolts in sequential order and in two steps.
Main bearings. Stage 1.
22 ft lbs.
Stage 2.
44 ft lbs

Big end bearings.
Stage 1.
11 ft lbs.
Then Rotate bolt head a further by 90 degrees

Head bolt torque must be done in 3 steps:
1st 22 ft lbs
2nd 43 ft lbs
final 47 ft lbs
use this sequence of tightening:
9 - 3 -1 -6 -8
7 - 5 - 2 -4 - 10

Flywheel spec:
65 ft lbs

Per BMW AG,
Jointing torque: 80 Nm
Loosen all bolts 1/2 turn
Jointing torque 50 Nm

http://www.adrianteo.com/files/cylinder-head-torque.pdf

The head torque settings are 75 nm plus a further 90 degrees (102 ft/lbs)

The torquing sequence is:-

9 5 1 3 7
front
10 6 2 4 8

what year?

you should have got them with the new gasket

According to my haynes manual for Landrover 200tdi, G - S reg,1989-1998 it goes as follows,
Stage 1:- Tighten all bolts to 30lb ft or 40Nm then
Stage 2:- Angle tighten a further 60 degrees then
Stage 3:- Angle tighten a further 60 degrees again.